Is the SAE 6000 SUPERCAT flange end, type ZSK113, carbon steel, zinc-nickel compatible with crimping sleeves for hydraulic and industrial hoses?

Yes. The SAE 6000 SUPERCAT flange end, type ZSK113, carbon steel, zinc-nickel is designed specifically for crimping in hydraulic and industrial hoses using a crimping sleeve appropriate for the hose type. Its carbon steel construction and zincânickel coating (6â10 Âµm) provide high corrosion resistance, supporting reliable performance after crimping when the correct sleeve and crimping parameters for the hose are used. Ensure you match the crimping sleeve dimensions and crimping specifications to the hose and to the SAE 6000 SUPERCAT flange end, type ZSK113, carbon steel, zinc-nickel to achieve a proper, leakâproof crimp.

Can the SAE 6000 SUPERCAT flange end, type ZSK113, carbon steel, zinc-nickel withstand aggressive chemical environments without degrading?

The SAE 6000 SUPERCAT flange end, type ZSK113, carbon steel, zinc-nickel offers very high corrosion resistance due to its 6â10 Âµm zincânickel coating (tested up to ~720 hours in salt spray), so it resists oxidation and general corrosive atmospheres far better than bare carbon steel. However, zincânickel is primarily a barrier and sacrificial coating optimized for chloride/saline and atmospheric corrosion; it is not chemically inert to strong acids, alkalis, or aggressive solvents. In strongly acidic or alkaline environments, oxidizing media, or exposure to specific industrial chemicals, the coating and underlying carbon steel can degrade over time. For applications involving aggressive or unknown chemicals, consult chemical compatibility data or choose stainless steel or specialty corrosionâresistant materials/coatings.

Can SAE 6000 SUPERCAT flange end, type ZSK113, carbon steel, zinc-nickel be reconditioned after surface damage?

Yes. in many cases the SAE 6000 SUPERCAT flange end, type ZSK113, carbon steel, zinc-nickel can be reconditioned after surface damage, but feasibility depends on the damage extent and required performance. Key points: - Superficial scratches, minor scuffs or localized coating removal: reconditioning is typically possible. Steps include cleaning (degrease, remove corrosion or contaminants), light mechanical smoothing or polishing of burrs, and reapplying a compatible zinc-nickel touch-up coating or passivation to restore corrosion protection. Ensure coating rebuild reaches similar thickness (6â10 Âµm) and adhesion. - Moderate surface damage that exposes base carbon steel over a limited area: possible to repair if substrate is sound (no deep gouges, cracks, or distortion). Repair requires removal of corrosion, surface preparation (abrasive blasting or chemical treatment), and professional re-coating with zinc-nickel or an equivalent corrosion-resistant system followed by inspection. - Severe damage (deep gouges, cracks, deformation, compromised sealing/mating faces, or loss of dimensional tolerances): not recommended to recondition for safety-critical hydraulic use. Flanges with structural damage or altered crimping/sealing surfaces should be replaced to maintain integrity and pressure ratings. - Quality control: after reconditioning, perform dimensional checks, inspect coating thickness and adhesion, and if applicable, pressure/leak tests or non-destructive testing to verify integrity. Use qualified plating/coating processes to match original corrosion resistance (target 6â10 Âµm zinc-nickel). - Compliance and liability: reconditioning should follow manufacturer recommendations, industry standards, and customer safety requirements. When in doubt for hydraulic applications, prefer replacement. Conclusion: Minor surface damage to SAE 6000 SUPERCAT flange end, type ZSK113, carbon steel, zinc-nickel can usually be repaired by proper surface preparation and re-coating to restore corrosion resistance; structural or sealing-surface damage warrants replacement.

Fitting flange SAE 6000 SUPERCAT, type ZSK113, carbon steel, zinc-nickel

All products, Fittings for high-pressure hoses/

Additional information

Material	CS – steel (cast iron)
Standard length [m]	30, 50

Fitting flange SAE 6000 SUPERCAT (SFS). Intended for crimping onto hydraulic and industrial hoses using a ferrule suitable for the hose type. Surface coated with zinc-nickel with a layer thickness of 6-10 µm, which offers very high corrosion resistance (up to 720 hours without corrosion in a salt spray chamber). Material: carbon steel, zinc-nickel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ZSK113-12-12-CN	Flange fitting SAE 3/4", hose 3/4" SUPERCAT, Zn-Ni	20	350	In stock	Enquiry
TI-ZSK113-16-12-CN	Flange fitting SAE 1", hose 3/4" SUPERCAT, Zn-Ni	20	350	In stock	Enquiry
TI-ZSK113-16-16-CN	Flange fitting SAE 1", hose 1" SUPERCAT, Zn-Ni	25	280	In stock	Enquiry
TI-ZSK113-20-16-CN	Flange fitting SAE 1.1/4", hose 1" SUPERCAT, Zn-Ni	25	280	In stock	Enquiry
TI-ZSK113-20-20-CN	Flange fitting SAE 1.1/4", hose 1.1/4" SUPERCAT, Zn-Ni	32	210	In stock	Enquiry
TI-ZSK113-24-20-CN	Flange fitting SAE 1.1/2", hose 1.1/4" SUPERCAT, Zn-Ni	32	210	In stock	Enquiry
TI-ZSK113-24-24-CN	Flange fitting SAE 1.1/2", hose 1.1/2" SUPERCAT, Zn-Ni	38	185	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Fitting flange SAE 6000 SUPERCAT (SFS). Intended for crimping onto hydraulic and industrial hoses using a ferrule suitable for the hose type. Surface coated with zinc-nickel with a layer thickness of 6-10 µm, which offers very high corrosion resistance (up to 720 hours without corrosion in a salt spray chamber). Material: carbon steel, zinc-nickel.