Is the CAMLOCK connector standard gasket, EPDM suitable for continuous use between -30Â°C and +150Â°C?

Yes. The CAMLOCK connector standard gasket, EPDM is specified for continuous use across an operating temperature range from -30Â°C to +150Â°C. EPDM (ethylene propylene diene monomer) is well suited to sustained exposure within that span: it maintains flexibility and sealing properties at low temperatures near -30Â°C and retains resistance to heat, weathering, ozone and many aqueous chemicals up to +150Â°C. Ensure compatibility with the specific media (strong hydrocarbons, oils, ketones and some solvents can degrade EPDM) and verify application-specific factors (pressure, compression set, mechanical wear, and duration at peak temperature). If the fluid or environment includes aggressive hydrocarbons or solvents, select a different elastomer. Otherwise, for typical water, steam, glycol, acids/bases and general industrial fluids, the CAMLOCK connector standard gasket, EPDM is suitable for continuous use within -30Â°C to +150Â°C.

Can the CAMLOCK connector standard gasket, EPDM withstand chemical exposure at temperatures from -30Â°C to +150Â°C?

CAMLOCK connector standard gasket, EPDM Format: EPDM gaskets are suitable for a wide temperature range (â30Â°C to +150Â°C) and show excellent resistance to weathering, ozone, steam, alkalis, and many polar chemicals. However, EPDM has poor resistance to fuels, aromatic and chlorinated hydrocarbons, oils, and many solvents. Therefore, while CAMLOCK connector standard gasket, EPDM Format will perform well thermally across the stated range, its chemical compatibility depends on the specific fluids involved. For service with hydrocarbons, fuels, oils, or aggressive solvents, choose a different elastomer (e.g., NBR, FKM) or verify compatibility with manufacturer chemical charts.

How should I maintain the CAMLOCK connector standard gasket, EPDM for reliable use between -30Â°C and +150Â°C?

To maintain the CAMLOCK connector standard gasket, EPDM for reliable use between -30Â°C and +150Â°C, follow these guidelines: 1. Inspection and replacement - Inspect gasket visually before each use for cuts, cracks, hardening, deformation or signs of chemical attack. - Replace the gasket immediately if you find any damage, excessive compression set, or loss of elasticity. - Keep a replacement schedule based on frequency of use and service conditions (e.g., quarterly for heavy use). 2. Cleaning - Clean gaskets after each use with mild soap and lukewarm water; rinse thoroughly and dry with a soft cloth. - Avoid solvents, petroleum-based cleaners, strong acids or alkalis which can swell or degrade EPDM. - For stubborn residues, use a diluted neutral detergent; rinse well. 3. Storage - Store gaskets flat or on a mandrel to avoid deformation. - Keep in a cool, dry, dark place away from direct sunlight, ozone sources (motors, UV lamps), heat sources, and sharp objects. - Recommended storage temperature: +5Â°C to +25Â°C, relative humidity moderate; avoid long-term storage above +50Â°C. 4. Lubrication and installation - Use only compatible lubricants: water-based or silicone-based greases approved for EPDM; avoid petroleum-based oils/greases. - Inspect mating surfaces of CAMLOCK coupling for burrs or damage before installing gasket. - Seat the gasket evenly without twisting; ensure correct compressionâsufficient to seal but not so tight as to cause permanent deformation. 5. Chemical compatibility and media - Confirm media compatibility with EPDM (good for water, steam, many alcohols, and some acids/alkalis; poor with hydrocarbons, oils, ketones). - If service involves aggressive chemicals or hydrocarbons, consider alternative materials. 6. Temperature cycling - Minimize rapid temperature swings when possible to reduce stress and compression set. - For repeated thermal cycling near limits (-30Â°C or +150Â°C), increase inspection frequency. 7. Documentation and traceability - Keep records of gasket material, installation date, operating conditions, inspections and replacements to predict lifespan and ensure safety. Following these practices will maximize sealing performance and lifespan of the CAMLOCK connector standard gasket, EPDM within the specified -30Â°C to +150Â°C range.

Gasket standard coupling CAMLOCK, EPDM

Additional information

Maximum operating temperature [°C]	150
Minimum operating temperature [°C]	-30

A standard gasket for the female part (socket) of a CAMLOCK coupling. Material: EPDM. Operating temperature: from -30°C to +150°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AC-G-050-E	Gasket EPDM 1/2"	-	-	In stock	Enquiry
AC-G-050-EX	Gasket EPDM 1/2"	-	-	In stock	Enquiry
AC-G-075-E	Gasket EPDM 3/4"	-	-	In stock	Enquiry
AC-G-075-EX	Gasket EPDM 3/4"	-	-	In stock	Enquiry
AC-G-100-E	Gasket EPDM 1"	-	-	In stock	Enquiry
AC-G-100-EX	Gasket EPDM 1"	-	-	In stock	Enquiry
AC-G-125-E	Gasket EPDM 1.1/4"	-	-	In stock	Enquiry
AC-G-125-EX	Gasket EPDM 1.1/4"	-	-	In stock	Enquiry
AC-G-150-E	Gasket EPDM 1.1/2"	-	-	In stock	Enquiry
AC-G-150-EX	Gasket EPDM 1.1/2"	-	-	In stock	Enquiry
AC-G-200-E	Gasket EPDM 2"	-	-	In stock	Enquiry
AC-G-200-EX	Gasket EPDM 2"	-	-	In stock	Enquiry
AC-G-250-E	Gasket EPDM 2.1/2"	-	-	In stock	Enquiry
AC-G-250-EX	Gasket EPDM 2.1/2"	-	-	In stock	Enquiry
AC-G-300-E	Gasket EPDM 3"	-	-	In stock	Enquiry
AC-G-300-EX	Gasket EPDM 3"	-	-	In stock	Enquiry
AC-G-400-E	Gasket EPDM 4"	-	-	In stock	Enquiry
AC-G-400-EX	Gasket EPDM 4"	-	-	In stock	Enquiry
AC-G-500-E	Gasket EPDM 5"	-	-	In stock	Enquiry
AC-G-500-EX	Gasket EPDM 5"	-	-	In stock	Enquiry
AC-G-600-E	Gasket EPDM 6"	-	-	In stock	Enquiry
AC-G-600-EX	Gasket EPDM 6"	-	-	In stock	Enquiry