Is SAE 6000 45Â° flange end, type ZSK312, heavy series, carbon steel suitable for crimping with a sleeve matched to my hydraulic hose type?

Yes. The SAE 6000 45Â° flange end, type ZSK312, heavy series, carbon steel is designed for crimping in hydraulic and industrial hose assemblies and is suitable for use with a crimping sleeve matched to your hydraulic hose type. Key points: - Design compatibility: The flange (SFL), 45Â° angled, heavy series construction is intended specifically for crimped terminations. - Sleeve requirement: Use a crimping sleeve specified for your hose construction (single wire, spiral, textile, etc.) and hose size to ensure correct grip and sealing. - Material: Carbon steel, galvanized finish provides adequate strength and corrosion resistance for typical hydraulic applications; ensure compatibility with your fluid and working environment. - Crimper and procedure: Use the correct crimping machine, die set, and crimping parameters recommended by the hose, sleeve, and fitting manufacturers to achieve specified crimp dimensions and pressure ratings. - Verification: After assembly, perform pressure and leak tests per industry/hose manufacturer standards to confirm integrity. If you provide the exact hose model and sleeve type, I can confirm exact sleeve dimensions and crimp settings.

Can SAE 6000 45Â° flange end, type ZSK312, heavy series, carbon steel be used with which crimping sleeve dimensions and dies for my hose?

SAE 6000 45Â° flange end, type ZSK312, heavy series, carbon steel requires a crimping sleeve sized to match the hose outer diameter and reinforcement type. Use a heavy-duty full-profile (Uâ or Câtype) steel sleeve whose inner diameter equals the hose OD and whose length matches the flangeâs collar length (typically 1.2â1.5Ã hose OD for heavy series). Wall thickness depends on hose pressure class-common values 2.5â4.0 mm for reinforced hydraulic hoses. Die set: heavy-series hydraulic crimping dies sized to the sleeve/hose OD (matched die kit for the sleeve manufacturer), capable of producing the specified crimp diameter and profile for SAE 6000 fittings. Verify exact sleeve inner length/thickness and die part number with hose and sleeve manufacturers before crimping.

What maintenance is required after crimping SAE 6000 45Â° flange end, type ZSK312, heavy series, carbon steel?

After crimping SAE 6000 45Â° flange end, type ZSK312, heavy series, carbon steel, perform the following maintenance to ensure seal integrity and service life: - Visual inspection: check the flange face, bolthole area and crimped sleeve for cracks, deformations, burrs, paint or galvanizing damage, and any signs of uneven crimping or gaps between sleeve and hose. - Dimensional check: verify crimp diameter and axial position against assembly specification for the hose and sleeve to confirm adequate compression. - Leak test: pressure-test the assembly at working and, if required, test pressures to detect leaks, seepage or bulging in the hose near the crimp. - Fastener and mating surface care: clean flange face and bolt holes; remove debris or corrosion; ensure bolts and nuts are undamaged and torqued to correct values when installed. - Corrosion protection: touch up damaged galvanizing or coating on the flange and sleeve with appropriate corrosion-inhibiting paint or galvanic repair compound to prevent rust on carbon steel. - Re-torque and retest after initial service: after first service run, recheck torque on flange bolts and repeat leak/pressure test to ensure stability of the crimped joint. - Monitor in service: periodically inspect for vibration damage, mechanical abrasion, oil or chemical exposure, and temperature cycling effects; replace assembly if permanent deformation, repeated leaks, or hose degradation appear. - Recordkeeping: log crimp dimensions, crimper ID and die set used, pressure test results and inspection dates to track quality and predict maintenance intervals. Do not re-crimp a damaged SAE 6000 45Â° flange end, type ZSK312, heavy series, carbon steel; replace the fitting and sleeve if crimp integrity is compromised.

Fitting flange SAE 6000 45°, type ZSK312, series heavy, carbon steel

All products, Fittings for high-pressure hoses/

Additional information

Material	CS – steel (cast iron)

Fitting flange SAE 6000 (SFL), angled 45°, series heavy. Intended for crimping onto hydraulic and industrial hoses using a ferrule suitable for the hose type. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-ZSK312-08-08	Flange fitting 45° SAE 1/2", hose 1/2", heavy	12	-	In stock	Enquiry
TI-ZSK312-08-10	Flange fitting 45° SAE 1/2", hose 5/8", heavy	16	-	In stock	Enquiry
TI-ZSK312-08-12	Flange fitting 45° SAE 1/2", hose 3/4", heavy	20	-	In stock	Enquiry
TI-ZSK312-12-08	Flange fitting 45° SAE 3/4", hose 1/2", heavy	12	-	In stock	Enquiry
TI-ZSK312-12-10	Flange fitting 45° SAE 3/4", hose 5/8", heavy	16	-	In stock	Enquiry
TI-ZSK312-12-12	Flange fitting 45° SAE 3/4", hose 3/4", heavy	20	-	In stock	Enquiry
TI-ZSK312-12-16	Flange fitting 45° SAE 3/4", hose 1", heavy	25	-	In stock	Enquiry
TI-ZSK312-16-12	Flange fitting 45° SAE 1", hose 3/4", heavy	20	-	In stock	Enquiry
TI-ZSK312-16-16	Flange fitting 45° SAE 1", hose 1", heavy	25	-	In stock	Enquiry
TI-ZSK312-20-16	Flange fitting 45° SAE 1.1/4", hose 1", heavy	25	-	In stock	Enquiry
TI-ZSK312-20-20	Flange fitting 45° SAE 1.1/4", hose 1.1/4", heavy	32	-	In stock	Enquiry
TI-ZSK312-24-20	Flange fitting 45° SAE 1.1/2", hose 1.1/4", heavy	32	-	In stock	Enquiry
TI-ZSK312-24-24	Flange fitting 45° SAE 1.1/2", hose 1.1/2", heavy	38	-	In stock	Enquiry
TI-ZSK312-32-24	Flange fitting 45° SAE 2", hose 1.1/2", heavy	38	-	In stock	Enquiry
TI-ZSK312-32-32	Flange fitting 45° SAE 2", hose 2", heavy	50	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Fitting flange SAE 6000 (SFL), angled 45°, series heavy. Intended for crimping onto hydraulic and industrial hoses using a ferrule suitable for the hose type. Material: carbon steel, galvanized.