Strong suction and discharge hose with an inner layer made of chemically resistant polyethylene with ultra-high molecular weight (UPE, UHMWPE), black and white MARBLE type, smooth, antistatic (R<10⁶ Ω). The inner layer is resistant to most acids and bases as well as many other aggressive chemicals (at elevated but not very high temperatures), making the hose widely used in the chemical and petrochemical industries. The MARBLE type UPE inner layer also complies with food hose requirements, features a low friction coefficient during flow, and prevents medium deposition on the walls. This significantly facilitates cleaning and allows for use in the cosmetic, pharmaceutical, and food industries as well. Reinforced with synthetic cord and steel spiral. The outer layer is made of chemically resistant EPDM rubber, antistatic (R < 10⁶ Ω), abrasion-resistant, ozone-resistant, and weather-resistant. Compliant with EN 12115:11 requirements (type Ω/T, fully antistatic (R < 10⁹ Ω) - ensures the dissipation of electrostatic charges through the hose walls, allowing use in all explosion hazard zones. Standards and requirements: Chemical hoses: EN 12115:2011 (type Ω/T). Food industry, contact with food (inner layer): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU, FDA 21 CFR 177.1520 (c), D.M. 21/03/73. Explosive atmospheres: ATEX directive (zones: 0, 1, 2, 20, 21, 22), EN 50014/ IEC 60079-0. Installation: use smooth fittings with a spigot ("tail" to the hose) without sharp or high ribs that could cut or damage the UPE inner layer when tightened. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Installation with clamp sleeves or band clamps. Inner layer: white-black UPE polyethylene. Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50°C. Inner layer: white-black UPE polyethylene. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: from 12 bar to 16 bar - depending on the hose diameter. Operating temperature: from -35°C to +100°C.

High-quality suction and pressure hose "FULL OHM" completely antistatic (Ω/T), designed for the transfer of highly flammable and chemically aggressive substances. The inner layer is made of perfluoroalkoxy polymer PFA (fluoropolymer with properties similar to Teflon), antistatic (R<10⁶ Ω), mirror-smooth, meeting high hygiene requirements (FDA, USP, European EU). Intermediate layers made of synthetic rubber, reinforced with synthetic cord and a steel wire spiral. The outer layer is MARBLE type (marbled), smooth, coated with polyethylene (UPE), antistatic (R<10⁶ Ω), meeting FDA requirements, odorless and tasteless, resistant to abrasion, ozone and aging, chemicals, and short-term action of aggressive acids. An advantage of the MARBLE layer is its low friction coefficient - the hose glides and does not soil the surfaces it contacts, making it easy to clean. Excellent chemical resistance of PFA and antistatic properties of both the inner and outer layers (R<10⁶ Ω) as well as across the wall of the hose (R<10⁹ Ω) make the hose a costly but technically ideal solution for applications requiring the highest safety in all explosion hazard zones (ATEX). Used in the chemical, petrochemical, pharmaceutical, and cosmetic industries, as well as in biotechnology. Not intended for sterilization in an autoclave. A version with additional built-in copper wires (M/T) is available on special order. Standards and requirements: Chemical hoses: EN 12115:2011. Food industry, contact with food: 1935/2004/EC, 2023/2006/EC (GMP); inner layer: 10/2011/EU, USP Class VI, FDA 21 CFR 177.1550; ISO 10993-4,-10,-11, non-cytotoxic (ISO 10993 Part 5); outer layer: FDA 21 CFR 177.1520. Contains no plasticizers, phthalates, or animal-derived substances. Explosive atmospheres: ATEX Directive (zones: 0, 1, 2, 20, 21, 22), EN 50014/IEC 60079-0. Confirmation of resistance and application conditions requires contact with Tubes International. Assembly: Use smooth fittings with a spigot ("tail" for the hose) that do not have sharp or high ribs that could cut or damage the inner layer of PFA when tightened. The diameter of the spigot should be precisely matched to the diameter of the hose to ensure tightness. Assembly with clamp sleeves or shell clamps. Inner layer: black PFA polymer. Reinforcement: synthetic cord, steel spiral. Outer layer: white-black UPE polyethylene, synthetic rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -35°C to +130°C.

Strong suction and discharge hose with an inner layer made of chemically resistant polyethylene with ultra-high molecular weight (UPE, UHMWPE). The inner layer is resistant to most acids and bases as well as many other aggressive chemicals (at elevated but not very high temperatures), making the hose widely used in the chemical and petrochemical industries. The UPE inner layer also complies with food-grade hose requirements, is free from phthalates and polycyclic aromatic hydrocarbons (PAH), and features a low friction coefficient during flow, preventing medium deposition on the walls. This significantly facilitates cleaning and allows for use in the cosmetic, pharmaceutical, and food industries as well. Reinforced with synthetic cord and steel spiral, with built-in copper wires for electrostatic discharge. The outer layer is made of chemically resistant EPDM rubber, resistant to abrasion, ozone, and weather conditions. Compliant with EN 12115:11 requirements (type M, resistance between hose ends R ≤ 100 Ω, guaranteed for hoses up to 40 m in length). Standards and requirements: Chemical hoses: EN 12115:2011. Food industry, contact with food (inner layer): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU (simulant fluids A, B, D2), FDA 21 CFR 177.1520, BfR III. Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50°C. Inner layer: white creamy UPE polyethylene. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 16 bar. Operating temperature: from -40°C to +100°C.

Very lightweight, flexible suction and discharge hose designed for the transfer of chemical substances. Made from thermoplastic vulcanizate TPV – a material that combines the processing advantages of thermoplastic polymers (PP – polypropylene) with the properties of vulcanized rubber (EPDM). Good chemical resistance - similar to EPDM rubber allows for use with many substances, including acids (hydrochloric, sulfuric), bases, salts, alcohols, glycols, and ketones, concentrated detergents. Not recommended for fuels, oils, aromatic solvents. Resistant to weather conditions, aging, and ozone. Low weight and small bending radius of the hose ensure ease of handling, which can be an advantage when transferring from tankers and containers. Note: All hose sizes have branding indicating approximate working pressure (WP 10 bar). Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: thermoplastic rubber TPV. Reinforcement: polyester braid, steel spiral. Outer layer: thermoplastic rubber TPV. Working pressure for temperature +23°C: from 12 to 14 bar - depending on hose diameter. Operating temperature: from -30°C to +80°C (working pressure dependent on temperature).

Hose for the transmission of almost all aggressive chemical substances. Specifically designed for the petrochemical industry for fuels with high concentrations of aromatic hydrocarbons, hot oil, and solvents. Due to the high overall chemical resistance of FPM rubber, it can be used for aggressive chemicals, in many cases also at elevated temperatures. The inner layer is made of smooth black FKM fluorine rubber. Reinforcement with synthetic cord. The outer layer is made of CR chloroprene rubber, resistant to weather conditions, ozone, abrasion, and oils. Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50ºC. Inner layer: black FKM rubber (FPM, viton). Reinforcement: synthetic cord. Outer layer: black CR rubber. Working pressure: 10 bar. Operating temperature: from -25°C to +100°C.

High-quality suction and discharge hose designed for the transfer of a wide range of aggressive chemical substances. The hose's broad application, primarily in the chemical industry, is conditioned by the excellent resistance of fluoropolymer FEP to aggressive solvents and concentrated alkalis and acids such as hydrochloric, sulfuric, phosphoric, nitric acids, as well as sodium and potassium hydroxides. The hose can also be used in the food and pharmaceutical industries. It is commonly used in cleanroom environments. The inner layer is made of white tetrafluoroethylene/fluoropropylene copolymer FEP (a thermoplastic fluoropolymer with properties similar to Teflon), mirror-smooth (prevents medium deposition on the walls and is easy to maintain cleanliness), odorless and tasteless, meeting high hygiene standards (FDA, USP Class VI). Intermediate layers made of white synthetic rubber include reinforcement with synthetic cord, a steel wire spiral, and two copper wires for discharging electrostatic charges. The outer layer is made of orange EPDM rubber, resistant to abrasion, ozone, and weather conditions. The hose features excellent chemical resistance and cleanliness of FEP, as well as exceptional temperature resistance. Specifically designed for Cleaning-in-Place (CIP) cleaning methods, including steam sterilization at 150ºC. Standards and requirements: Chemical hoses: EN 12115:2011 (type M). Food industry, contact with food (inner layer): USP Class VI, FDA 21 CFR 177.1550. Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: white, smooth FEP. Reinforcement: synthetic cord, steel spiral. Outer layer: orange smooth EPDM rubber. Working pressure: 16 bar. Vacuum: 0.9 bar. Operating temperature: from -40°C to +150°C.