Is the Hose for acids and alkalis, anti-static MANICHEM MARBLE safe for food contact and compliant with EU and FDA regulations at temperatures up to 50Â°C?

Hose for acids and alkalis, anti-static MANICHEM MARBLE Format . Based on the provided description, the inner MARBLE UPE layer is stated to "comply with food hose requirements" and the hose is declared compliant with relevant standards for food contact: EU regulations 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU and FDA 21 CFR 177.1520 (c), plus national D.M. 21/03/73. The hoseâs operating temperature range is -35Â°C to +100Â°C, so use at 50Â°C falls within that range. However the text also explicitly advises that confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50Â°C. Therefore: technically the construction and declared standards indicate suitability for food contact and regulatory compliance and the temperature 50Â°C is within the hoseâs rated range, but final confirmation for specific food-contact use and chemical resistance at or near 50Â°C must be obtained from Tubes International before use.

Can Hose for acids and alkalis, anti-static MANICHEM MARBLE be used in explosion-hazard zones (ATEX) and dissipate electrostatic charges safely?

Hose for acids and alkalis, anti-static MANICHEM MARBLE Format: Yes. The hose features antistatic inner UPE and outer EPDM layers (R < 10^6 Î©) and is manufactured to EN 12115:2011 (type Î©/T, fully antistatic R < 10^9 Î©), which ensures dissipation of electrostatic charges through the hose wall and permits use in all ATEX explosion-hazard zones (0, 1, 2, 20, 21, 22) when installed correctly. For safe ATEX application, follow required installation: use smooth spigot fittings matched to hose diameter, clamp sleeves or band clamps, and avoid damaging the UPE inner layer. Confirm chemical compatibility and conditions (especially above 50Â°C) with Tubes International before use.

Can Hose for acids and alkalis, anti-static MANICHEM MARBLE be cleaned and sterilized for pharmaceutical/cosmetic use without damaging the UPE inner layer?

Hose for acids and alkalis, anti-static MANICHEM MARBLE Format. yes, the hose can be cleaned and sterilized for pharmaceutical and cosmetic use in most standard procedures without damaging the UPE (UHMWPE) inner layer, with the following important caveats: - The MARBLE UPE inner layer is chemically resistant to most acids, bases and many aggressive chemicals and is specifically stated as suitable for food, cosmetic and pharmaceutical contact (compliance: 1935/2004/EC; 2023/2006/EC GMP; 10/2011/EU; FDA 21 CFR 177.1520 (c); D.M. 21/03/73). Its low friction surface and resistance to medium deposition facilitate cleaning. - Compatible cleaning/sterilization methods: typical chemical cleans (acid/alkaline detergents within the materialâs resistance range), aqueous sanitizers, and standard CIP procedures at moderate temperatures are acceptable. Mechanical cleaning is aided by the smooth UPE surface. - Temperature limit: do not exceed recommended operating/chemical resistance temperatures. Manufacturer notes require consultation for use above 50Â°C. clearance from Tubes International is needed for higher-temperature sterilization (e.g., prolonged steam at high temperatures). - Mechanical care: avoid sharp-edged fittings or over-tightening that can cut or damage the UPE layer. Use smooth spigots precisely matched to hose ID and clamp sleeves/band clamps as specified. - Antistatic and safety properties: antistatic inner/outer layers and EN 12115:2011 / ATEX compliance remain effective if cleaning does not alter conductive paths; follow recommended agents that do not leave insulating residues. Recommendation: proceed with standard pharmaceutical/cosmetic cleaning and sterilization within the hoseâs chemical and temperature limits, and contact Tubes International for written confirmation and guidance if processes involve temperatures above 50Â°C, aggressive agents outside the specified resistance, or validated sterilization cycles.

Hose for acids and bases, antistatic MANICHEM MARBLE

All products, Chemical hoses/

Additional information

Material	UPE – polyethylene UPE
Maximum operating temperature [°C]	100
Minimum operating temperature [°C]	-35
Vacuum resistance	yes
Standard length [m]	10, 20, 40, 60/ 120
Reinforcement	steel spiral, synthetic cover

Strong hose suction – delivery with layer inner with resistant chemical polyethylene o ultra-high weight molecular (UPE, UHMWPE), black – white type MARBLE (marbled), smooth, antistatic (R 6 Ω). The inner layer is resistant to most acids and bases and many other aggressive chemicals (in elevated, ale nie very high temperatures), co makes, that hose is wide used in industry chemical and petrochemical. Layer inner with UPE type MARBLE is also compliant with requirements for hoses food, is characterized also low a coefficient friction during flow and prevents deposition medium na walls. This significantly facilitates cleaning and allows use also in the cosmetic, pharmaceutical and food industry. Reinforcement cord synthetic and spiral steel. Layer outer with resistant chemical rubber EPDM, antistatic (R 6 Ω), resistant na abrasion, ozone and conditions atmospheric. compliant with requirements EN 12115:11 (type Ω/T, completely antistatic (R 9 Ω) – ensures discharge charges electrostatic also through wall hose, co allows na use we all zones hazard explosion. standards and requirements: hoses chemical: EN 12115:2011(type Ω/T). industry food, contact with food (Layer inner): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU, FDA 21 CFR 177.1520 (c), D.M. 21/03/73. atmospheres explosive: directive ATEX (zones: 0, 1, 2, 20, 21, 22), EN 50014/ IEC 60079-0. assembly: should use fitting with a spigot („tail” for hose) smooth, not having sharp or high notches, which could po crimping cut or damage layer inner with UPE. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Assembly with clamping ferrules or shell clamps. Inner layer: white-black polyethylene UPE. Confirmation of resistance and application conditions requires contact with Tubes International, in particular for temperatures above 50°C. Inner layer: white-black polyethylene UPE. Reinforcement: synthetic cord, steel spiral. Outer layer: black rubber EPDM. pressure working: from 12 bar to 16 bar – depending on diameter hose. temperature use: from -35°C to +100°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MT-MANICHEM-M-006	Hose MANICHEM MARBLE 6x16 mm	6	16	In stock	Enquiry
MT-MANICHEM-M-008	Hose MANICHEM MARBLE 8x20 mm	8	16	In stock	Enquiry
MT-MANICHEM-M-010	Hose MANICHEM MARBLE 10x20 mm	10	16	In stock	Enquiry
MT-MANICHEM-M-013	Hose MANICHEM MARBLE 13x23 mm	12	16	In stock	Enquiry
MT-MANICHEM-M-016	Hose MANICHEM MARBLE 16x28 mm	16	16	In stock	Enquiry
MT-MANICHEM-M-019	Hose MANICHEM MARBLE 19x31 mm	20	16	In stock	Enquiry
MT-MANICHEM-M-025	Hose MANICHEM MARBLE 25x37 mm	25	16	In stock	Enquiry
MT-MANICHEM-M-032	Hose MANICHEM MARBLE 32x44 mm	32	16	In stock	Enquiry
MT-MANICHEM-M-038	Hose MANICHEM MARBLE 38x51 mm	38	16	In stock	Enquiry
MT-MANICHEM-M-050	Hose MANICHEM MARBLE 50x66 mm	50	16	In stock	Enquiry
MT-MANICHEM-M-065	Hose MANICHEM MARBLE 63.5x79.5 mm	65	16	In stock	Enquiry
MT-MANICHEM-M-075	Hose MANICHEM MARBLE 75x91 mm	75	16	In stock	Enquiry
MT-MANICHEM-M-100	Hose MANICHEM MARBLE 100x118 mm	100	16	In stock	Enquiry
MT-MANICHEM-M-125	Hose MANICHEM MARBLE 125x146 mm	125	12	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Strong hose suction – delivery with layer inner with resistant chemical polyethylene o ultra-high weight molecular (UPE, UHMWPE), black – white type MARBLE (marbled), smooth, antistatic (R 6 Ω). The inner layer is resistant to most acids and bases and many other aggressive chemicals (in elevated, ale nie very high temperatures), co makes, that hose is wide used in industry chemical and petrochemical. Layer inner with UPE type MARBLE is also compliant with requirements for hoses food, is characterized also low a coefficient friction during flow and prevents deposition medium na walls. This significantly facilitates cleaning and allows use also in the cosmetic, pharmaceutical and food industry. Reinforcement cord synthetic and spiral steel. Layer outer with resistant chemical rubber EPDM, antistatic (R 6 Ω), resistant na abrasion, ozone and conditions atmospheric. compliant with requirements EN 12115:11 (type Ω/T, completely antistatic (R 9 Ω) – ensures discharge charges electrostatic also through wall hose, co allows na use we all zones hazard explosion. standards and requirements: hoses chemical: EN 12115:2011(type Ω/T). industry food, contact with food (Layer inner): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU, FDA 21 CFR 177.1520 (c), D.M. 21/03/73. atmospheres explosive: directive ATEX (zones: 0, 1, 2, 20, 21, 22), EN 50014/ IEC 60079-0. assembly: should use fitting with a spigot („tail” for hose) smooth, not having sharp or high notches, which could po crimping cut or damage layer inner with UPE. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Assembly with clamping ferrules or shell clamps. Inner layer: white-black polyethylene UPE. Confirmation of resistance and application conditions requires contact with Tubes International, in particular for temperatures above 50°C. Inner layer: white-black polyethylene UPE. Reinforcement: synthetic cord, steel spiral. Outer layer: black rubber EPDM. pressure working: from 12 bar to 16 bar – depending on diameter hose. temperature use: from -35°C to +100°C.

Additional information

Material	UPE – polyethylene UPE
Maximum operating temperature [°C]	100
Minimum operating temperature [°C]	-35
Vacuum resistance	yes
Standard length [m]	10, 20, 40, 60/ 120
Reinforcement	steel spiral, synthetic cover