Our products
Select options This product has multiple variants. The options may be chosen on the product page / Details90° angled tube connection, for connection using a ring and DIN 2353 nut, with an end designed for a measuring hose. The connection is available as: L (light series) and S (heavy series), while the end is intended for hoses DN2 or DN4 and supplied complete with a compression sleeve. Working pressure depends on the connection mounted on the tube and the working pressure of the hose. Material: steel with a zinc-nickel coating.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight tube connection for assembly using a ring and DIN 2353 nut, with an end designed for a measuring hose. The connection is available as: L (light series) and S (heavy series), while the end is intended for hoses DN2 or DN4 and supplied complete with a clamping sleeve. Working pressure depends on the connection mounted on the tube and the working pressure of the hose. Material: steel with a zinc-nickel coating.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight coupling with external BSP, NPTF thread and hose measurement end, supplied with a clamping sleeve. Available in three variants: with external BSP thread (60° cone), with external BSP thread (flat seal) or with external NPTF thread (tapered). Material: steel with zinc-nickel coating. Working pressure: 400 bar and 630 bar - depending on the size. Operating temperature: from -30°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsInternal and external threaded nipple for pressure gauges with standard pressure connection according to EN 837-1. Allows the installation of a pressure gauge to a larger size socket. The pressure gauge is mounted to the internal thread d1. This connection is self-sealing – the cone at the bottom of the hole d1 presses into the centering hole of the pressure gauge connection. Threads d1 and d2 are secured against loosening of the connection by a special adhesive. Designed for non-aggressive liquids and gases, for the installation of pressure gauges, taps, and pressure valves, as well as other accessories equipped with this type of connection. Material: AISI 316Ti steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBanjo screw DIN 7643, size M8, M10, and 1/8" BSP. Material: carbon steel, galvanized. Material: steel with zinc-nickel coating. Working pressure: 200 bar. Operating temperature: from -30°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBimetallic thermometer with a rear sensor made according to the EN 13190 standard for measuring the temperature of liquids, vapors, and gases in industrial devices, particularly in heating systems. It features a quick response to temperature changes and ease of reading due to a clear scale. The thermometer is mounted to the device using a screwed protective cover with an external thread, which protects the sensor and allows for the replacement of the thermometer without disrupting the process – the thermometer is pressed into the sensor cover. At least 50% of the sensor length should be exposed to the measured temperature medium. Also available in a stainless steel version - SS version (dust-tight housing - IP65). Material: galvanized steel (housing), glass (window), brass (sensor and cover). Nominal diameter: 63 mm, 100 mm. Degree of protection of the housing: IP41. Accuracy class: 2. Sensor length: 50 mm, 80 mm, 100 mm. Cover strength: 160 bar. Cover connection: GW BSP 1/2". Measurement range: from -30°C to +400°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCollet sleeve designed for crimping thermoplastic micro hoses DN2 and DN4, used in hydraulic measurement and control systems. Material: steel with a zinc-nickel coating.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMeasurement handle for activation at low pressure. It has a connection for a manometer, a quick coupling with a shut-off valve, and a vent (for TA-M-101-21A - valve).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very flexible and elastic, resistant to kinking hose designed for hydraulic oil, water-based fluids, and other media. Used in measurement systems, control systems, hydraulic brake systems in bicycles, and micro-hydraulics (car roof opening systems). The outer layer is made of abrasion-resistant polyurethane or polyamide and is micro-perforated, allowing the hose to be used for gas media. The hose has vacuum resistance up to 0.93 bar. Temperatures above 80°C may reduce the hose's lifespan. The DN2 hose made of polyamide (ZC-TEST8-5021PA) has successfully passed impulse tests of 1 million cycles. Inner layer: polyester or polyamide. Reinforcement: single aramid braid. Outer layer: black polyurethane or polyamide. Working pressure: from 412 bar to 500 bar, depending on the diameter and type of hose. Operating temperature: from -40°C to +100°C (for water and air up to +70°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMiniature quick-connect measurement plug DN1.2, with plastic or metal cap and external thread, manufactured in Sweden, designed for measuring static, dynamic pressure, and vacuum in hydraulic systems. The plug is equipped with a valve ensuring leak-free connection, disconnection, and sealing, even at 90% vacuum. Measurement plugs made of hardened steel, durable and maintenance-free. Connections with external thread sealed using an O-ring recessed in the front surface (type A) or an O-ring at the front surface (type B). Material: galvanized steel. Sealing: NBR. Working pressure: 600 bar (for plugs TA-M-120: 400 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMeasurement plug equipped with a PVC cap, intended for connection with TEMA 100 socket, additionally connected with thermoplastic hose. Material: galvanized steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick-connect plug for measurement SNAP-CHECK, manufactured in Sweden, designed for pressure measurement in hydraulic systems. The quick-connect sockets are connected by a hose to a pressure gauge, while the hardened steel quick-connect plugs are typically permanently installed in the hydraulic system and equipped with shut-off valves. Connection of the socket to the plug is possible under pressure up to 300 bar. The working pressure for the unplugged plug is 600 bar, and the minimum burst pressure is 2400 bar. The working pressure for the connected socket and plug is also 600 bar, while the minimum burst pressure is 1300 bar. The precise construction of the quick-connects ensures the tightness and reliability of the measurement points in the hydraulic system. The connection range for measurement plugs allows for easy configuration of the connection. Quick-connect plugs are supplied as standard with red plastic caps. Working pressure: 600 bar. Switching pressure: up to 300 bar. Body material: galvanized steel. Sealing: NBR. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug with shut-off valve for diagnostic quick coupling, with internal NPT thread, used for pressure measurement in hydraulic systems. Manufactured according to ISO 15171-1 and SAE J1502 standards, interchangeable with connectors from other manufacturers. Quick coupling plugs made of hardened steel are typically permanently installed in the hydraulic system, while the quick coupling sockets remain connected by a hose to the pressure gauge. The connection of the socket to the plug should only occur when the system is not operating, with no pressure or very low pressure of a few bars. The working pressure for the plug not connected to the socket is 400 bar, and the minimum burst pressure is 1600 bar. The working pressure for the connected socket and plug is also 400 bar, while the minimum burst pressure is 1300 bar. The socket and plug are equipped with valves that ensure leak-free connection and disconnection as well as sealing. Their flat surfaces minimize residual oil leakage and air inclusion into the system (leakage approx. 0.1 ml during disconnection, air inclusion approx. 0.02 ml during connection). For proper operation, it is essential to maintain the cleanliness of the valve surfaces. Working pressure: 400 bar. Burst pressure: 1300 bar. Vacuum: up to 0.9 bar. Hydraulic oil flow at Δp = 3 bar: 4.2 [l/min]. Material: galvanized steel. Sealing: NBR. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug with shut-off valve for diagnostic quick coupling, with external NPT thread, used for pressure measurement in hydraulic power systems. Manufactured according to ISO 15171-1 and SAE J1502 standards, interchangeable with couplings from other manufacturers. Quick coupling plugs made of hardened steel are typically permanently installed in the hydraulic system, while the quick coupling sockets remain connected via a hose to the pressure gauge. The connection of the socket to the plug should only occur when the system is not operating, with no pressure or very low pressure of a few bars. The working pressure for the disconnected plug is 400 bar, and the minimum burst pressure is 1600 bar. The working pressure for the connected socket and plug is also 400 bar, while the minimum burst pressure is 1300 bar. The socket and plug are equipped with valves that ensure leak-free connection and disconnection as well as sealing. Their flat surfaces minimize residual oil leakage and air inclusion into the system (leakage approx. 0.1 ml during disconnection, air inclusion approx. 0.02 ml during connection). For proper operation, it is essential to maintain the cleanliness of the valve surfaces. Working pressure: 400 bar. Burst pressure: 1300 bar. Vacuum: up to 0.9 bar. Hydraulic oil flow at Δp = 3 bar: 4.2 [l/min]. Material: galvanized steel. Sealing: NBR. Operating temperature: from -40°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, very flexible and elastic, resistant to kinks hose designed for hydraulic oil, water-based fluids, and other media. Used in measurement systems, control systems, and hydraulic brake systems in bicycles. On special order, the outer layer is micro-perforated. Inner layer: polyester. Reinforcement: single aramid braid. Outer layer: black polyurethane. Working pressure: 625 bar or 660 bar, depending on the hose diameter. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBlind plug for quick coupling connector PD, standard ISO 15171-1. Material: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug cap TEMA 100 protecting against dirt and damage. Material: PVC or carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBrass needle valve with manometer connection, used in hydraulic systems as an isolating element for the manometer from the installation. The valve protects the manometer from overload and pressure spikes during opening and allows for its replacement. It is available in two versions: straight – in-line (FPE) and angular 90° (FPEA). It has a thread under the knob, allowing for panel mounting. An adapter with index DC-FPE-FPEA must be used for the valve, tightened to the connection with internal thread (ordered separately). Material: nickel-plated brass (body), carbon steel (needle), galvanized steel (connection - nut), plastic (knob). Sealing: NBR. Connection: 2 x 1/4" BSP female (manometric). Operating temperature: from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe set is equipped with miniature measuring quick couplings DN1.2 manufactured in Sweden, designed for measuring static, dynamic pressure, and vacuum in hydraulic systems. Based on a classic "push to connect" quick coupling design with a locking mechanism consisting of balls, a spring, and a locking sleeve. The socket and plug are equipped with valves ensuring leak-free connection and disconnection and tightness, even at a vacuum of 90%. Measuring plugs made of hardened steel, durable and maintenance-free. Connections with external threads sealed using an O-ring recessed in the front surface (type A) or an O-ring at the front surface (type B). This ensures simple and quick configuration of connections. The remaining elements of the measuring set include manometers (not included in the set) mounted in measuring holders, adapters, and measuring hoses. The vent valve in the measuring holder allows for the removal of air bubbles from the system, which increases the accuracy of dynamic pressure measurement. The set can be used for pressure measurements on machines equipped with TEMA SYSTEM 100 measuring plugs (some working machines e.g., VOLVO, HIAB, SAMSUNG) or by installing plugs in the system during measurement. The flexible adapter TA-M-139 allows the set to be used for measurements on widely used connections with M16x2 threads. Any suitable type of manometer (not included in the set) with a typical manometric connection with a 1/4” BSP external thread can be used for measurements with the set. Recommended manometer version: 63 mm manometer type FM-631 - bottom connection. Sealing of the manometer in the holder socket using a thread washer and an O-ring 10.8x2.2, or a manometric washer inside the socket. The set is delivered in a plastic case and includes the following elements: 1. Measuring holder for low-pressure connection (manometer connection 1/4” BSP, quick coupling socket, vent). 2. Measuring plug, GZ 1/8" BSP, type A, plastic cap. 3. Measuring hose (DN2, 630 bar), L=2.5 m with quick coupling plug TA-M-120 and socket TA-M-150. 4. Adapter, GW 1/4" BSP / GZ 1/8" BSP, type A. 5. Adapter, GW 1/8" BSP / GZ 1/4" BSP, type B. Sealing: NBR rubber. Working pressure: up to 600 bar, for plugs TA-M-120 - 400 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe basic measurement set is intended for the diagnostics of hydraulic and pneumatic systems through the measurement of static, dynamic, and vacuum pressure. The set includes a plastic case with designated spaces for two 63 mm pressure gauges and a DN2 (630 bar) hose with fittings: measuring GW M16x2 and for the gauge GW 1/4” BSP, with a length of 2000 mm. The set does not include pressure gauges, which must be selected and ordered separately. Material of the hose fittings: steel with a zinc-nickel coating. Working pressure: up to 630 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe measurement set is designed for the diagnostics of hydraulic and pneumatic systems through the measurement of static, dynamic, and vacuum pressure. The set includes a plastic case with designated spaces for two 63 mm pressure gauges, a DN2 hose (630 bar) with two measuring ends GW M16x2, 2000 mm in length, as well as couplings and adapters: 1. M16x2 measuring coupling with a metal cap, with GZ 1/4” BSP, type E - 2 pcs. 2. M16x2 measuring coupling with a metal cap, with GZ M8x1, type F - 1 pc. 3. M16x2 measuring coupling with a metal cap, with GZ M10x1, type F - 1 pc. 4. Connection with GW 1/4” BSP to the pressure gauge, partitioned, with GZ M16x2 - 2 pcs. 5. Connection with GW 1/4” BSP to the pressure gauge, with GW M16x2 - 1 pc. 6. Reducing adapter GZ 3/8” BSP / GW M10x1, type E - 1 pc. 7. Reducing adapter GZ 1/2” BSP / GW M10x1, type E - 1 pc. The set does not include pressure gauges, which must be selected and ordered separately. Material of couplings: steel with a zinc-nickel coating. Sealing: NBR. Working pressure: up to 630 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMeasurement set designed for diagnosing hydraulic systems through pressure measurement. The set is supplied in a plastic case with the following configuration: 1. Glycerin pressure gauge 63 mm, lower connection 1/4” BSP, 0 ÷ 100 bar, glycerin pressure gauge 63 mm, lower connection 1/4” BSP, 0 ÷ 250 bar, glycerin pressure gauge 63 mm, lower connection 1/4” BSP, 0 ÷ 400 bar. 2. Measurement connector M16x2 with plastic cap, with GZ 1/4” BSP, type E, measurement connector M16x2 with plastic cap, with GZ 3/8” BSP, type E. 3. Measurement connector M16x2 with plastic cap, with GZ 1/4” NPT, type C, measurement connector M16x2 with plastic cap, with GZ 3/8” NPT, type C. 4. Measurement connector M16x2 with plastic cap, with GZ M10x1, type F, measurement connector M16x2 with plastic cap, with GZ 7/16”-20 UNF, type F, measurement connector M16x2 with plastic cap, with GZ 9/16”-18 UNF, type F. 5. Measurement connector M16x2 with metal cap, with DIN 2353 connection with GW M18x1.5, 12L. 6. Metal cap M16x2. 7. Connection with GW 1/4” BSP to pressure gauge, with GW M16x2, connection with GW 1/2” BSP to pressure gauge, with GW M16x2. 9. Connection with GW 1/4” BSP to pressure gauge, partitioned, with GZ M16x2. 10. Hose DN2 (630 bar) with two measurement ends GW M16x2 L = 1 m, hose DN2 (630 bar) with two measurement ends GW M16x2 L = 2 m. Material of connectors: galvanized steel. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMeasurement set designed for diagnosing hydraulic systems through pressure measurement. The set is supplied in a plastic case with the following configuration: 1. Glycerin manometer 63 mm, lower connection 1/4” BSP, 0 ÷ 160 bar, glycerin manometer 63 mm, lower connection 1/4” BSP, 0 ÷ 315 bar. 2. Measurement connector M16x2 with plastic cap, with GZ 1/4” BSP, type E, measurement connector M16x2 with plastic cap, with GZ 3/8” BSP, type E. 3. Measurement connector M16x2 with plastic cap, with GZ 1/4” NPT, type C. 4. Measurement connector M16x2 with plastic cap, with GZ M10x1, type F. 6. Metal cap M16x2. 7. Connection with GW 1/4” BSP to manometer, with GW M16x2. 8. 90° angled connection with GW 1/4” BSP to manometer, with GZ M16x2. 10. Hose DN2 (630 bar) with two measurement ends GW M16x2 L = 1.5 m. Connector material: galvanized steel. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBANJO straight fitting DIN 7642 with an end designed for micro hoses, complete with a crimping sleeve. Material: steel with a zinc-nickel coating. Working pressure: 200 bar. Operating temperature: from -30°C to +120°C.
