Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsMini double-acting cylinder ISO 6432 STD, type 112 with magnet, without cushioning. It is designed to operate with filtered oil-lubricated or non-oil-lubricated air and does not require additional maintenance activities. The cylinder is made with a stainless steel sleeve. The dimensions of the outer covers for certain diameters have been reduced, allowing for the installation of cylinders in constrained and limited spaces. The lifespan of cylinders with NBR seals is 15 million cycles, with polyurethane seals 30 million cycles. The presented values should not be considered binding or guaranteed, but only as a reference due to the variability of many factors, including radial and axial loads, speed, temperature, or air losses (limit values). Piston diameter: Ø 8, 10, 12, 16, 20, and 25 mm. Stroke length: from 5 to 500 mm. Operating pressure: from 0.8 to 10 bar (Ø 8, 10, 12 mm); from 0.6 to 10 bar (Ø 16, 20, 25 mm). Sealing: polyurethane, NBR, FKM/FPM. Operating temperature: from -10°C to +150°C depending on the seal used.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMini double-acting cylinder ISO 6432 STD, type 113, has been designed to operate with filtered oil-lubricated or non-oil-lubricated air and does not require additional maintenance. The cylinder is made with a stainless steel sleeve. The dimensions of the external covers for certain diameters have been reduced, allowing for the installation of cylinders in confined and restricted spaces. The lifespan of cylinders with NBR seals is 15 million cycles, with polyurethane seals 30 million cycles. The presented values should not be considered binding or guaranteed, but merely as a reference due to the variability of many factors, including radial and axial loads, speed, temperature, or air losses (limit values). Piston diameter: Ø 16, 20, and 25 mm. Stroke length: from 10 to 500 mm. Operating pressure: from 0.6 to 10 bar. Sealing: polyurethane, NBR. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble-acting short-stroke actuator with a retracted piston rod and magnet. The SSCY series is characterized by a compact design and is intended for installation in confined spaces. The operational lifespan of actuators without transverse load with NBR seals is 15 million cycles, and with polyurethane seals, it is 30 million cycles. Due to the variability of many factors affecting lifespan, the presented values should not be considered binding or guaranteed, but only as a reference. Available piston diameters: Ø 12 ÷ 80 mm. Working stroke: from 5 to 120 mm. Seal material of the actuator: NBR or polyurethane. Operating pressure: from 0.4 to 10 bar - depending on the piston diameter. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMicro-actuators of single-acting design (with retracted piston rod) intended for installation in confined spaces. It features a sealing ring (o-ring), allowing direct mounting in the machine body. Oil-free operation is possible. Important! When the actuator operates at high frequency, it is advisable that the piston does not reach the end position. Material: nickel-plated brass (body), AISI 303 steel (piston for Ø6 - Ø10), brass (piston for Ø16), nickel-plated steel (nut), spring steel (spring), brass (plain bearing). Operating pressure: 2÷6 bar. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMini double-acting cylinder ISO 6432 STD, type 110, without magnet, without cushioning. It is designed to operate with filtered oil-lubricated or non-oil-lubricated air and does not require additional maintenance. The cylinder is made with a stainless steel sleeve. The dimensions of the outer covers for certain diameters have been reduced, allowing for installation in confined and restricted spaces. The lifespan of cylinders with NBR seals is 15 million cycles, with polyurethane seals 30 million cycles. The presented values should not be considered binding or guaranteed, but only as a reference due to the variability of many factors, including radial and axial loads, speed, temperature, or air losses (limit values). Piston diameter: Ø 8, 10, 12, 16, 20, and 25 mm. Stroke length: from 5 to 500 mm. Operating pressure: from 0.8 to 10 bar (Ø 8, 10, 12 mm); from 0.6 to 10 bar (Ø 16, 20, 25 mm). Sealing: polyurethane, NBR, FKM/FPM. Operating temperature: from -10°C to +150°C depending on the seal used.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe CMPC series compact actuator, with an externally threaded piston rod, features a lightweight design and short installation length, allowing for mounting in hard-to-reach places. The special profile of the actuator is connected to the outer covers using screws, ensuring optimal axial stiffness and increasing the variety of mounting options. It is equipped with a magnet embedded in the piston, and grooves in the profile allow for the use of magnetic sensors without additional accessories. Manufactured according to ISO 15552 standard. This standard enables easy and quick selection and replacement of the actuator during machine maintenance work. Piston diameter: Ø 32 ÷ Ø 100. Actuator type: double-acting, double-acting with a through piston rod, and single-acting. Piston rod material: C45 chrome-plated steel or stainless steel. Minimum operating pressure: 0.4 ÷ 0.6 bar, depending on the diameter. Maximum operating pressure: up to 10 bar. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSquare-type proximity sensor SQ for actuators features secure and quick mounting using an eccentric screw, the possibility of installation with a screwdriver and a 2.5 mm hex key, stop edges that stabilize the sensor during installation, increased resistance to weather conditions and moisture (IP 67, IP 68, IP 69K). Sensor housing material: polyamide (PA). Supply voltage: 5 ÷ 30V AC/DC (10 ÷ 30V AC/DC - HALL). Operating temperature: from -30°C to +80°C (from -5°C to +80°C - dynamic installations).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFork head for mounting on the piston rod of the actuator. For use in cases of loads not aligned with the axis of the actuator's piston rod. The fork head provides greater mounting options. Thread: M4 ÷ M36x2. Material: galvanized carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsISO bracket for mounting with a swivel flange. Included: 4 screws with washers. Material: cast aluminum (flange), galvanized carbon steel (screws and washers).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsArticulated head for mounting on the piston rod of the actuator. For use in cases of loads not aligned with the axis of the actuator's piston rod. The articulated head provides greater mounting options. Thread: M4 ÷ M36x2. Material: galvanized carbon steel (head), steel (joint).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWobble flange with double ear for mounting on the rear part of the actuator cover, with a pin. Allows for the movement of the pneumatic actuator during operation. Included: 4 screws with washers, 1 pin, 2 retaining rings. Material: cast aluminum (flange), steel + bronze + PTFE (bushing), galvanized carbon steel (screws and washers), galvanized carbon steel (pin), stainless steel (retaining ring).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReplacement seal kit for actuator ISO 15552 version: STD, TYPE A, SERIES 3. Material: NBR. Diameter: 32 ÷ 125.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe bracket is used to mount the proximity sensor on cylindrical actuators. Sensor brackets DXF: with indices W09500001... - intended for actuators with an aluminum sleeve, with indices W09500005... - intended for actuators with a stainless steel sleeve. Material: stainless steel, plastic.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCETOP bracket for mounting with a swivel flange. Included: 4 screws with washers. Material: cast aluminum (flange), galvanized carbon steel (screws and washers).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWobble flange with a single ear for mounting on the rear part of the actuator cover, without a pin. Allows for the movement of the pneumatic actuator during operation. Included: 4 screws. Material: cast aluminum (flange), steel + bronze + PTFE (bushing), galvanized carbon steel (screws and washers).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMounting bracket (angle bracket) intended for ISO 15552 actuator series STD, series 3, "two flat", with a diameter from 32 mm to 125 mm, model A. Included: 2 screws. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWobble flange with ball joint for mounting on the rear part of the actuator cover. Included: 4 screws with washers. Material: cast aluminum (flange), steel (joint), galvanized carbon steel (screws and washers).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet of interchangeable seals for ISO 15552 actuator Ø 160 - 200. Material: NBR. Diameter: Ø 160, Ø 200.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet of interchangeable seals for compact actuator ISO 21287, LINER series. Material: polyurethane. Diameter: 80, 100.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsProximity sensor mounting bracket for ISO 15552 actuators, in version with cylindrical sleeve. Material: aluminum. Diameter: 160 ÷ 200.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSet of interchangeable seals for compact actuator ISO 21287, LINER series. Material: polyurethane. Diameter: 32 ÷ 63.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReplacement seal kit for compact actuator ISO 21287, LINER series. Material: polyurethane. Diameter: 20, 25.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNut for use on the piston rod to secure, e.g., fork/joint heads (for diameters 32 ÷ 125 mm).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsProximity sensor mounting adapter for DST/ST brackets used in actuators of series R1 and ISO 15552. Material: plastic.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMounting bracket model A for mini cylinder ISO 6432. Cylinder sizes: Ø8, Ø10, Ø12, Ø16, Ø20, Ø25. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMounting flange for pneumatic actuator, for attachment to the rear or front cover of the actuator. Allows for permanent mounting of the actuator in machines and devices. Range of actuator diameters: 32 mm ÷ 125 mm. Included: 4 mounting screws. Material: galvanized carbon steel (flange, screws, and washers).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMounting collar for pneumatic actuator, for attachment to the rear or front cover of the actuator. Allows for permanent mounting of the actuator in machines and devices. Actuator size: Ø8 ÷ Ø25. Material: galvanized carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAC mounting bracket for cylindrical actuator - RNDC series. Packaged individually. Actuator sizes: Ø32, Ø40, Ø50. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMini actuators of the TP series, manufactured according to ISO 6432 standards, have covers made of high-strength plastic, while the cylinders are made of anodized aluminum. Available versions: with magnet or without magnet. Piston diameter: Ø 16, 20, and 25 mm. Working stroke: from 1 to 80 mm (with the possibility of ordering up to 500 mm). Working pressure: from 0.6 to 10 bar. Sealing: polyurethane. Operating temperature: from -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMini double-acting cylinder ISO 6432 STD, type 109 with cushioning, without magnet. It is designed to operate with filtered oil-lubricated or non-oil-lubricated air and does not require additional maintenance. The cylinder is made with a stainless steel sleeve. The dimensions of the outer covers for certain diameters have been reduced, allowing for installation in confined and restricted spaces. The lifespan of cylinders with NBR seals is 15 million cycles, with polyurethane seals 30 million cycles. The presented values should not be considered binding or guaranteed, but only as a reference due to the variability of many factors, including radial and axial loads, speed, temperature, or air losses (limit values). Piston diameter: Ø 16, 20, and 25 mm. Stroke: from 10 to 320 mm. Operating pressure: from 0.6 to 10 bar. Sealing: polyurethane, NBR, FKM/FPM. Operating temperature: from -10°C to +150°C depending on the seal used.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble-acting actuator with magnet and damping ISO 15552 series 3. It features a special sleeve with minimized weight, made of anodized, calibrated aluminum, and two grooves for sensor mounting on a common plane with power supply ports. The remaining walls are smooth and easy to clean. The actuator cover is made of high-pressure aluminum casting. Piston diameter: Ø 32 ÷ 100 mm. Stroke length: from 50 to 800 mm. Operating pressure: from 0.4 to 10 bar. Sealing: NBR, polyurethane. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe CMPC series compact actuator, with an internally threaded piston rod, is characterized by its lightweight and short design, allowing for installation in hard-to-reach places. The special profile of the actuator is connected to the outer covers using screws, ensuring optimal axial stiffness and increasing the variety of mounting options. Depending on the version, it may or may not be equipped with a magnet embedded in the piston, and grooves in the profile allow for the use of magnetic sensors without additional equipment. Manufactured according to ISO 15552 standard. This standard allows for easy and quick selection and replacement of the actuator during machine maintenance work. Piston diameter: Ø 32 ÷ Ø 100. Actuator type: double-acting, double-acting with a through piston rod, and single-acting with a retracted piston rod. Piston rod material: C45 chrome-plated steel or stainless steel. Maximum operating pressure: up to 10 bar. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSingle-acting actuator ISO 15552 type A, features a cover made of high-pressure aluminum casting and a profile made of calibrated anodized aluminum, which includes longitudinal grooves on three walls allowing for direct mounting and protection of the piston position sensors. The same grooves are used for direct mounting of valves and other mechanical components. Piston diameter: Ø 32 ÷ 63 mm. Stroke length: from 30 to 200 mm. Operating pressure: from 0.4 to 10 bar. Sealing: polyurethane. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble-acting short-stroke actuator with rotation protection using a magnet. The SSCY series is characterized by a compact design and is intended for installation in confined spaces. The operational lifespan of actuators without transverse load with NBR seals is 15 million cycles, and with polyurethane seals, it is 30 million cycles. Due to the variability of many factors affecting lifespan, the presented values should not be considered binding or guaranteed, but only as a reference. Available piston diameters: Ø 12 ÷ 80 mm. Working stroke: from 10 to 80 mm. Seal material of the actuator: NBR, polyurethane. Operating pressure: from 0.4 to 10 bar - depending on the piston diameter. Operating temperature: from -10°C to +80°C - depending on the type of seal.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe CMPC series compact actuator, with an externally threaded piston rod, is characterized by its lightweight and short construction, allowing for installation in hard-to-reach places. The special profile of the actuator is connected to the outer covers using screws, ensuring optimal axial stiffness and increasing the variety of mounting options. Depending on the version, it may or may not be equipped with a magnet embedded in the piston, and grooves in the profile allow for the use of magnetic sensors without additional accessories. Manufactured according to the NFE 49-004-1 and 2 standards (UNITOP). This standard allows for easy and quick selection and replacement of the actuator during machine maintenance work. Selected actuators have a through hole in the piston rod. Piston diameter: Ø 32 ÷ Ø 100. Actuator type: single-acting and double-acting. Piston rod material: C45 chrome-plated steel or stainless steel. Minimum operating pressure: 0.4 ÷ 0.6 bar, depending on the diameter. Maximum operating pressure: up to 10 bar. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble-acting cylinder with a passing double rod can be used as an actuator in systems where protection against rotation is required. Axial dimensions compliant with ISO 15552 standard. Standard configuration with magnet and cushioning. Piston diameter: Ø 32, 40, 50, 63, 80, 100 mm. Maximum recommended stroke length: from 25 to 500 mm. Operating pressure: up to 10 bar. Sealing: polyurethane. Working medium: filtered compressed air, oiled or non-oiled. Forces generated at 6 bar extend/retract: Ø 32 - 434/350 N, Ø 40 - 678/597 N, Ø 50 - 1060/940 N, Ø 63 - 1683/1471 N, Ø 80 - 2714/2295 N, Ø 100 - 4241/3812 N. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBC bracket for mini cylinder ISO 6432. Includes 1 pin and 2 retaining rings. Cylinder sizes: Ø8, Ø10, Ø12, Ø16, Ø20, Ø25. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSupport bracket model BC for cylindrical actuator series RNDC. Supplied with 2 screws. Actuator size: Ø32, Ø40, Ø50. Material: carbon steel, galvanized.
