Can CETOP bracket for pneumatic actuator flange B, model GL support both clockwise and counterclockwise swivel mounting with the included 4 screws and washers?

Yes . the CETOP bracket for pneumatic actuator flange B, model GL supports both clockwise and counterclockwise swivel mounting using the included 4 screws and washers. The bracketâs swivel flange (cast aluminum) plus the 4 galvanized carbon steel screws and washers are provided to secure the actuator in either rotational orientation, so you can mount the actuator to swivel in either direction without needing additional fasteners. Ensure screws are tightened to the manufacturerâs recommended torque and verify alignment for smooth swivel operation.

Can CETOP bracket for pneumatic actuator flange B, model GL be mounted on different surface materials using the included 4 screws and washers?

Yes - the CETOP bracket for pneumatic actuator flange B, model GL Format can be mounted to different surface materials using the included 4 screws and washers, provided the mounting surface and screw engagement meet basic mechanical requirements. The flange is cast aluminum and the fasteners are galvanized carbon steel; this combination suits common substrates (steel, aluminum, wood, plastics) if you ensure: correct hole alignment, adequate thread engagement or use of inserts for soft materials, sufficient substrate thickness to carry the load, and corrosion compatibility for the installation environment. For high loads, vibration, or corrosive conditions, use appropriate anchors, thread inserts, longer or graded fasteners, or consult an engineer.

Can CETOP bracket for pneumatic actuator flange B, model GL resist corrosion in outdoor environments with the included galvanized screws and washers?

Partially, but with limitations. CETOP bracket for pneumatic actuator flange B, model GL uses a cast aluminum flange and galvanized carbon steel screws and washers. Cast aluminum offers good natural corrosion resistance outdoorsâforming a protective oxide layer that withstands weathering and most atmospheric conditions. Galvanized carbon steel fasteners provide sacrificial zinc coating that protects against rust for a time, making them suitable for general outdoor use. However, long-term corrosion resistance depends on exposure severity: - Mild environments (urban, suburban, occasional rain): the materials should perform well for extended periods. - Marine or highly corrosive environments (salt spray, constant humidity, chemical exposure): galvanized coatings can rapidly degrade; aluminum may suffer pitting or galvanic corrosion where it contacts steel if the zinc coating becomes compromised. - Constant wetting/drying cycles, pooling water, or abrasive contamination accelerate deterioration. Recommendations to improve durability: - For coastal or aggressive environments, use stainless steel fasteners (A2/A4) or apply additional protective coatings. - Ensure proper drainage and avoid trapping moisture between flange and mating surfaces. - Regular inspection and maintenance (re-tighten, replace corroded screws) will extend service life. Conclusion: CETOP bracket for pneumatic actuator flange B, model GL is suitable for general outdoor use with galvanized screws/washers, but for marine or very aggressive environments, upgrade fasteners or apply extra protection to ensure long-term corrosion resistance.

A bracket CETOP for flange actuator pneumatic B, model GL

All products, Pneumatic actuators/

Additional information

Material	AL – aluminum
Standard length [m]	10, 2

A bracket CETOP for mounting with a flange swivel. In the set: 4 screws with washers. Material: aluminum cast (flange), steel carbon galvanized (screws and washer).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MW-W0950322008	A bracket MOD.GL-032	-	-	In stock	Enquiry
MW-W0950402008	A bracket mod. GL-040	-	-	In stock	Enquiry
MW-W0950502008	A bracket MOD.GL-050	-	-	In stock	Enquiry
MW-W0950632008	A bracket MOD.GL-063	-	-	In stock	Enquiry
MW-W0950802008	A bracket MOD.GL-080	-	-	In stock	Enquiry
MW-W0951002008	A bracket MOD.GL-100	-	-	In stock	Enquiry
MW-W0951252008	A bracket MOD.GL-125	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

A bracket CETOP for mounting with a flange swivel. In the set: 4 screws with washers. Material: aluminum cast (flange), steel carbon galvanized (screws and washer).