Can the TrÃ³jnik redukcyjny "T" do wÄÅ¼a, kopolimer acetalowy, typ NA handle continuous operation at 10 bar in gas systems?

Yes . the TrÃ³jnik redukcyjny "T" do wÄÅ¼a, kopolimer acetalowy, typ NA can handle continuous operation at 10 bar in gas systems, provided the following conditions are met: - The stated working pressure is âup to 10 bar,â so continuous operation at that pressure is within the published rating. - Ensure the operating temperature, gas type (chemical compatibility) and dynamic loads (pulsation, shock, vibration) do not reduce the effective pressure rating for POM (acetal copolymer). - Verify seals and connected hose/end fittings are also rated for continuous 10 bar service and compatible with the gas. - For safety-critical or regulated gas applications, follow applicable standards and perform pressure testing, leak checks and periodic inspections. If all compatibility and installation checks are satisfied, the TrÃ³jnik redukcyjny "T" do wÄÅ¼a, kopolimer acetalowy, typ NA is suitable for continuous 10 bar gas operation.

Is the TrÃ³jnik redukcyjny "T" do wÄÅ¼a, kopolimer acetalowy, typ NA suitable for pneumatic systems operating near 10 bar?

TrÃ³jnik redukcyjny "T" do wÄÅ¼a, kopolimer acetalowy, typ NA is suitable for pneumatic systems operating near 10 bar only if the systemâs maximum working pressure does not exceed 10 bar and operating conditions match the productâs intended uses (control systems, gas transport, vacuum systems). Ensure temperature, dynamic loads, pressure spikes, and fluid compatibility are within the manufacturerâs specifications for acetal copolymer (POM). For continuous or safetyâcritical applications at or near 10 bar, verify safety margins, applicable standards, and consider higherârated fittings or consult the manufacturer.

Does TrÃ³jnik redukcyjny "T" do wÄÅ¼a, kopolimer acetalowy, typ NA resist chemical exposure in fluid transport systems?

TrÃ³jnik redukcyjny "T" do wÄÅ¼a, kopolimer acetalowy, typ NA: Acetal copolymer (POM) offers good chemical resistance to many common fluids used in control, pneumatic and hydraulic systems. oils, greases, water, air, and many solvents. However, its resistance is limited against strong acids, strong bases, halogenated hydrocarbons, and some aromatic solvents, which can cause swelling, stress cracking or degradation over time. Given the application (transport of gases and liquids, vacuum systems) and working pressure up to 10 bar, TrÃ³jnik redukcyjny "T" do wÄÅ¼a, kopolimer acetalowy, typ NA is suitable for many standard fluids but may not be appropriate for aggressive chemical exposures. For critical or unknown chemicals, consult chemical compatibility charts for POM or contact the manufacturer with the specific fluid, concentration and temperature to confirm compatibility.

Trójnik redukcyjny “T” do węża, kopolimer acetalowy, typ NA

All products, Low-pressure fittings and adapters/

Additional information

Material	P – material (plastic)

Reducing “T” fitting for hose, type NA. Designed for use in control systems, in installations for the transport of gases and liquids, in vacuum systems, etc. Working pressure: up to 10 bar. Material: acetal copolymer (POM).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
NA-7618903004	Reducer connector "T" DN 2.5, hose 3 mm / 4 mm / 3 mm	3	10	In stock	Enquiry
NA-7618904006	Reducer connector "T" DN 2.7, hose 4 mm / 6 mm / 4 mm	4	10	In stock	Enquiry
NA-7618906004	Reducing connector "T" DN 4, hose 6 mm / 4 mm / 6 mm	6	10	In stock	Enquiry
NA-7618908004	Reducer connector "T" DN 5.6, hose 8 mm / 4 mm / 8 mm	8	10	In stock	Enquiry
NA-7618908006	Reducer connector "T" DN 5,6, hose 8 mm / 6 mm / 8 mm	8	10	In stock	Enquiry
NA-7618908012	Reducer connector "T" DN 5,6, hose 8 mm / 12 mm / 8 mm	8	10	In stock	Enquiry
NA-7618910006	Reducer connector "T" DN 7, hose 10 mm / 6 mm / 10 mm	10	10	In stock	Enquiry
NA-7618910008	Reducer connector "T" DN 7, hose 10 mm / 8 mm / 10 mm	10	10	In stock	Enquiry
NA-7618910013	Reducer connector "T" DN 7, hose 10 mm / 13 mm / 10 mm	10	10	In stock	Enquiry
NA-7618912006	Reducer connector "T" DN 8.6, hose 12 mm / 6 mm / 12 mm	12	10	In stock	Enquiry
NA-7618912008	Reducer connector "T" DN 8.6, hose 12 mm / 8 mm / 12 mm	12	10	In stock	Enquiry
NA-7618912010	Reducer connector "T" DN 8.6, hose 12 mm / 10 mm / 12 mm	12	10	In stock	Enquiry
NA-7618915006	Reducer connector "T" DN 11, hose 15 mm / 6 mm / 15 mm	16	10	In stock	Enquiry
NA-7618915008	Reducing connector "T" DN 11, hose 15 mm / 8 mm / 15 mm	16	10	In stock	Enquiry
NA-7618918010	Reducer connector "T" DN 14, hose 18 mm / 10 mm / 18 mm	18	10	In stock	Enquiry
NA-7618918015	Reducer connector "T" DN 14, hose 18 mm / 14 mm / 18 mm	18	10	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Reducing “T” fitting for hose, type NA. Designed for use in control systems, in installations for the transport of gases and liquids, in vacuum systems, etc. Working pressure: up to 10 bar. Material: acetal copolymer (POM).