Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery intended for water cooling in smelters, foundries and we all use, where hose rubber works close source heat. coated fiber glass resistant to temperature up to +530°C caused radiation thermal. used in systems cooling. especially recommended for installation water at furnaces metallurgical. resistant to momentary action splashes red-hot hot metal. Roll length: 60 m or 120 m. Inner layer: black EPDM rubber. Reinforcement: cord synthetic. Outer layer: EPDM rubber coated fiber glass. Working pressure: 10 bar. Operating temperature: od -40°C up to +120°C, outer up to +530°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA general-purpose hydraulic hose o reduced diameter outer and weight and increased flexibility. meets standards: EN 857 2SC, EN45545-2. Inner layer: black synthetic rubber. Reinforcement: a double steel braid. Outer layer: black, flame-retardant synthetic rubber. Working pressure: from 90 bar to 400 bar depending on the diameter hose. Operating temperature: od -40°C up to +100°C. For water and air, the maximum working temperature is +70°C. For air above 17 bar, microperforation of the outer layer is required.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA light, flexible hose with a calibrated outer diameter, intended for pneumatic, hydraulic, oil, fuel, lubrication and chemical systems. Available in colours: natural, black, blue, red, yellow. Hose material: polyamide PA 12 (nylon). Working pressure: from 19 bar to 28 bar, depending on the diameter and wall thickness wall hose. Operating temperature: od -40°C up to +80°C (for media based on water +70°C). standard: SAE J 844 (diameter od 1/8" for 5/16").
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, colorless, clear, flexible hose free of smell and taste, non-toxic, nie containing phthalates DEHP. designed specially for use in pumps peristaltic. used for dispensing and portioning cold and hot products food, for soaps and detergents, for paints and in laboratories. soft Material hose (60° Shore (A)) is very flexible and ensures very good service life over 500 hours use in pump peristaltic. hose is good alternative for used often hoses, PVC or silicone. is flexible even in temperature -40°C and withstands elevated temperature up to +121°C. has good resistance chemical na range substances chemical, np. acids and bases. Nie recommended for fats, high-percentage alcohols and hydrocarbons. resistant na ozone, oxygen and light solar, flame-retardant. is characterized low extractability (penetration components material for medium). meets requirements hygienic and for contact with food: European 10/2011 EU (for conditions and substances acc. to certificate), American FDA, NSF-51. possible sterilization steam, oxide ethylene or radiation. Length of a full hose roll 15 m. pressure working determined relative to pressure bursting at factor safety 1:5. Material: tygoprene® - thermoplastic elastomer styrene (TPE). Maximum operating temperature: up to +121°C. temperature brittleness: -66°C. Hardness: 60° Shore (A). Density: 0.9 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLow-pressure hose suction-delivery with transparent layer inner with resistant chemical PFA and thick layer external with transparent silicone. intended for various applications in industry pharmaceutical, cosmetic, food and chemical, where besides the highest cleanliness, asepsis and resistance chemical required is observation flow medium. Layer inner with polymer perfluoroalkoxy PFA (polymer fluorine o properties close for PTFE), transparent, mirror smooth, free of smell and taste, inert chemical, meeting high requirements hygienic (FDA, USP, European EU). Reinforcement spiral of steel stainless ensures good resistance na vacuum. thick Layer outer with silicone cross-linked compounds platinum o smooth surface features properties nie adhesion (hose nie „adhesives ”) and small a coefficient friction. can be easily purified at use weak detergent. The design hose combines advantages PFA with flexibility silicone and its resistance na temperature. hose has small minimal radius bends, is flexible and flexible in low and elevated temperatures, resistant na cyclic bending in accordance with ASTM D 2176 and na loads dynamic. standards and requirements hygienic: Inner layer: USP Class VI, 3-A Sanitary Standards 18-03 Class I, 10/2011/EU, FDA, ISO 10993-4, -10, -11, non-cytotoxic (ISO 10993 Part 5), ICH Q3D; Outer layer: USP Class VI, 3-A Sanitary Standards 18-03 Class I, D.M. 21/03/73, FDA, BfR, European Pharmacopoeia 3.1.9, ISO 10993-4, -10, -11, non-cytotoxic (ISO 10993 Part 5). hose compliant with 1935/2004/EC, 2023/2006/EC (GMP), made in Cleanroom ISO 14644-1 Class 8, nie contains phthalates, adipates, nitrosamines, substances origin animal, substances subject EC 1907/2006 (REACH). Confirmation of resistance and application conditions requires contact with Tubes International. For confirmation of resistance and conditions of use, please contact Tubes International. assembly: should use fitting with a spigot („tail” for hose) smooth, not having sharp or high notches, which could po crimping cut or damage layer inner with PFA. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. assembly ferrules clamping or hose clamps (clamps). Inner layer: transparent polymer PFA. Reinforcement: spiral of steel stainless AISI 302. Outer layer: transparent silicone. pressure working: from 1 bar to 3 bar, depending on diameter hose. temperature use: from -30°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details
WEICON paste assembly Anti-Seize HIGH-TECH, container 120 g
All products | Cleaning agents, maintenance products, assembly compounds, and protective coatings0 złPaste assembly Weicon Anti-Seize High Tech ensures protection against corrosion, seizing and „cold welding”, especially on steel stainless. recommended especially for use in extreme conditions e.g.: at high temp., agents aggressive, high pressures, as well as for lubrication loaded bearings and surfaces sliding (only in engines low-speed). eliminates squeals and squeaking, has good properties sealing, allows easy assembly and disassembly components. economical in use (1 kg on ok. 40 ÷ 50 m 2 ) and free od metals toxic, consistency NLGI - Class 1. temperature use: od -40°C up to +1400°C. conducts heat. resistant to changes temperatures and loads pressure (230N/mm 2 ). Packaging - container 120 g. - Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe HPA screw-together plug of a hydraulic quick coupling, intended for installations at very high pressures with large mechanical loads. Used in hydraulic presses, rescue equipment, hydraulic lifts, cutters, etc. It can be connected / disconnected when residual pressure is present in the system. Caps should be ordered separately. Material: carbon steel. Sealing: NBR. Flow: 1/4" - 16.4 l/min; (Δp = 4 bar), 3/8" - 21.3 l/min; (Δp=4 bar). Working pressure: 700 bar. Burst pressure: 1/4" - 2100 bar (coupling connected), 3/8" - 1850 bar (coupling connected), 1/4" - 1490 bar (plug disconnected), 3/8" - 1500 bar (plug disconnected). Operating temperature: from -25°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug quick coupling DN11.8 with fitting for hose, without a flange, facilitating fast connection spray gun for water with a hose or with other accessories for washing. Material: steel AISI 303/304L. Working pressure: 200 bar. Operating temperature: up to +100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA high-quality NiTO water quick coupling plug 1/2" with a thread internal. Material: brass chrome-plated. Working pressure: up to 25 bar. Operating temperature: up to +80°C. Sealing: NBR (not suitable for gasolines and oils).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA PERROT lever coupling plug with a weld-on connection with wide application, among others in agriculture, horticulture, industry, construction, road and tunnel building, groundwater drainage, sewage treatment plants, wastewater discharge, and environmental protection. Material: steel carbon, galvanized. Working pressure: up to 10 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug coupling dry-break DRY-MATE with a thread internal of AISI 316 stainless steel. Used in the chemical, pharmaceutical industry, agriculture and transfer systems. Nie is intended for media gas. Installed on the pressure side (tank side). The plug design is based on a ball valve, which ensures a completely unobstructed flow. The plug is supplied complete with polypropylene caps. Coupling material: body - steel AISI 316, latch CAMLOCK - steel AISI 316. Sealing: valve - PTFE. pressure working: up to 7 bar. Operating temperature: up to 150°C. Maximum leakage: 1 ml (1") and 2 ml (1.1/2" and 2").
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCotter pin securing is used to securing against accidental loosening nuts on the plug side of coupling SKV. Assembly between a clip securing a lock nut. Diameter D - outer diameter. Material: red PVC.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA compact, two-piece medium-pressure ball valve intended for demanding general applications. It can be used for precision fittings (instrumentation) for industry chemical, petrochemical, pharmaceutical, power generation, process engineering - for liquids and for gases. Intended for in-line mounting. The valve is characterized by a large size range to ensure an adequately large flow, tightness closing (permissible leakage internal through sealing the ball 0.1 Ncm 3 /min), high durable and low torque swivel. designed for use in position completely open or completely closed. Each valve is pressure-tested with nitrogen. Certified according to ISO 15848-1:2006 (E). Material the body: steel AISI 316. Material the ball and stem: steel AISI 316. Material lever: steel AISI 304, PVC. sealing the ball: modified PTFE. sealing stem: PTFE. Operating temperature: from -42°C to +204°C. pressure working: up to 137 bar (depending od temperature). connection: inch LET-LOK®.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsShut-off valve type V3V L, two-position, three-way, with venting of the pneumatic system, terminated with push-in connections on both sides (hose - hose). Lockable version, prevents opening by unauthorized persons. Supplied complete with a padlock and two keys. Working pressure: 10 bar. Operating temperature: from -20°C to +60°C. Medium: filtered compressed air, oiled or non-oiled.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA set connection GA, serves for connecting individual element installation preparation compressed air series G. W a set finds connector and 2 screw. Available in shape: "L", "T" and "U". pressure supply: up to 10 bar. Operating temperature: up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling HAMMER LUG type 200 o wide range applications (for conveying water, air, gas, oil) meeting requirements greater applications in the scope medium pressures. precision matched surface sealing parts female and male causes reliable sealing pressure. set: part male, female + A nut. color: grey (part male, female), blue (A nut). Material: steel carbon A105. Connection: NPT female. sealing: metal/metal (cone). pressure: 2000 PSI (138 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug coupling reloading TW type VK with a thread internal BSP and with a lining E-CTFE. Intended for mounting on hose ends or pipe installations having a male BSP thread. Made in accordance with the EN ISO 14420-6 standard (formerly DIN 28450). used for most aggressive chemical media, for which resistance corrosion steel acid-resistant AISI 316 is insufficient. E-CTFE is characterized very high chemical resistance in wide the scope temperatures (in approximation from -40°C to +130°C). is resistant na operation all acids, alkalis and other aggressive substances (Range pH 1 ÷ 14). has high properties mechanical, in particularly hardness and resistance na abrasion. Material: steel stainless. sealing thread (type the gasket GD): teflon.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter reducing with a BSPT male thread and with a thread internal BSP intended for use in pipe connections of industrial installations. Material: malleable cast iron. Operating temperature: up to +300°C. Working pressure: 25 bar (up to +120°C), 20 bar (up to +300°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle comb 8 channel, flat-jet, terminated a thread external 1/4" BSP. intended for blowing off with greater surfaces all contamination: liquids, fine chips, filings itp. is characterized high force blowing at low level noise. ideal for construction knives air. works in difficult conditions, np. in very high temperatures. compliant of the standard OSHA 1910.95 (b), STD 1-13.1 and the directive 2003/10/EC. Material: ULTEM1000. pressure working: up to 10 bar. Operating temperature: from -20°C to +200°C. flow: 580 l/min (at a pressure of 8 bar). level noise: 81.5 dB (at a pressure of 8 bar). force blowing: 5.05 N.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCEJN 116 quick-coupling socket with a female thread and with a valve intended for hydraulic installations at very high pressures. Used in hydraulic presses, rescue equipment, hydraulic lifts, cutters, etc. Optionally, the socket can be fitted with a ring to prevent accidental disconnection. Supplied as standard with a cap to protect against contamination. Material: hardened steel, galvanized. Sealing: NBR. Flow: 6 l/min (Δp = 4 bar). Nominal diameter: 2.5 mm. Working pressure: 1500 bar (coupling connected). Burst pressure: 3000 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA high-quality NiTO water quick coupling socket 3/4" with fitting for hose. Material: brass chrome-plated. Working pressure: up to 25 bar. Operating temperature: up to +80°C. Sealing: NBR (not suitable for gasolines and oils).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket coupling CAMLOCK B with a BSPT male thread or NPT made in accordance with the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer coupling, especially in the petrochemical industry. Working pressure: up to 10 bar, depending on the coupling size. Material: aluminum. Levers: steel AISI 304 (in sizes 1.1/4" for 4" - Levers made of brass). Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsEAR CLIP clamping ring with 2 ears for mounting various types of low-pressure hoses, braid-reinforced or without reinforcement. Easy and quick installation using dedicated pincers. Rounded edges inside the ring protect the hose from damage. Material: galvanized carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsElbow with BSP female thread, type A9, intended for connecting pneumatic components (including hoses) to one another. A tight connection usually requires additional sealing: PTFE tape or sealant for a tapered thread, or aluminum or copper washers for a parallel thread. Material: nickel-plated brass. Working pressure: 60 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° butt-weld elbows for pressure applications made of pipes. Model 3D compliant with the standard EN 10253-4 (steel stainless). Equivalent to the design according to DIN 2605-1 type 3. With an EN 10204 3.1 material certificate. Widely used in industry in the construction of installations and pipelines, among others as element of complete welded ends for metal and rubber hoses (welded with threaded and flanged ends) and other couplings and fittings. On request, other sizes and materials are also available, including elbows with metric dimensions and elbows according to ASME. Note: These are standard type A fittings according to EN 10253, with the same wall thickness of the weld ends and the body. Their pressure resistance is lower than that of a straight pipe of the same diameter and wall thickness. Working pressure elbow should determine using coefficient correction pressure the given in standards EN 10253 or DIN 2605-1 (The given values are approximately and are 0.7÷0.8 pressure corresponding dimensionally tubes). Material: steel AISI 321, AISI 316Ti. Working pressure: od 56 up to 208 bar - depending on diameter.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA fitting with a female thread for high-pressure washers. Material: steel carbon.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting socket SKV with tail type INTERLOCK intended for hoses hydraulic type 4SH, R13, R15 (in rozmiarach 3/4" ÷ 1.1/2"). Material: steel galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA hydraulic fitting (type P - with a special "tail" for a thermoplastic hose) with a thread external BSP, sealing on a 60° cone (AGR). Intended for crimping in UHP thermoplastic hoses by means of a clamping ferrule appropriate for the hose type. Material: steel carbon, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrew-together threaded fitting type S2 with BSPT male thread (thread sealing), manufactured in accordance with EN 14424, intended for rubber hoses and certain types of thermoplastic hoses with soft textile reinforcement (without wire spiral). Widely used in the fuel sector in fuel and gas distribution lines (e.g., LPG). The basic version is made entirely of brass; also available in a stainless steel version (fitting) with a chrome-plated brass sleeve. Material: brass (B). Working pressure: 16 bar (up to 25 bar for DN25). Operating temperature: from -20°C to +65°C (from -30°C to +70°C for LPG).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight tube fitting type RST, without a nut, intended for low-pressure rubber and plastic hoses, unreinforced and with textile reinforcement, with an external steel braid. Commonly used in flexible lines for sanitary fittings, fuel and air installations, etc. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBrass Screw-together connector for hoses NiTO type A with a BSP thread with a flat seal. Material: brass. Working pressure: 25 bar. Operating temperature: up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMini actuator double-acting operation ISO 6432 STD, type 110, without magnet, without cushioning. It has been designed to work with filtered air, oiled or non-oiled, and does not require additional maintenance operations. A stainless steel sleeve was used to make the actuator. The dimensions of the external covers of some diameters have been reduced, which allows mounting the actuators in difficult and confined spaces. The service life of actuators with NBR seals is 15 million cycles, with polyurethane ones 30 million cycles. The presented values should not be treated as binding or guaranteed, but only as a reference due to the variability of many factors, including loads radial and axial, speed, temperature, czy losses air (values limit). Piston diameter: Ø 8, 10, 12, 16, 20 and 25 mm. stroke working: od 5 for 500 mm. pressure working: od 0.8 up to 10 bar (Ø 8, 10, 12 mm); od 0.6 up to 10 bar (Ø 16, 20, 25 mm). Sealing: polyurethane, NBR, FKM/FPM. Operating temperature: from -10°C to +150°C depending on used seal.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA nut Intended for connections parts male and female coupling HAMMER LUG, type 1502. Material: steel chromium-molybdenum 4130.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA nut with a thread BSP, type VT124. Material: steel AISI 316. The given dimensions are indicative and may differ slightly depending on the manufacturer.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA DIN 3015 heavy clamp, type 201 (with a top plate) intended for quick, easy, durable and aesthetic mounting of pipes, cables and hoses in various branches of industry, in above-ground and marine installations. Made in accordance with the DIN 3015 standard. The clamp is mounted to the structure by welding the clamp base (it is also possible to bolt it on or mount it on a rail). As standard, the clamp has a profiled (grooved) surface of the pipe hole. In addition to the standard metal element, you can order: extension plates, rails and bolts for mounting clamp sets. The selection of element should be consulted with TUBES INTERNATIONAL®. Material clamp: aluminum. Material bolts: steel galvanized. Material plate: steel galvanized. Material base: steel carbon. Operating temperature: up to +350°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure Water gun SG25 with lance extension for applications industrial. Suitable for warm and cold water. The lever mechanism does not require the operator to use much force, which translates into comfortable and pleasant work. part outlet terminated a thread internal M22x1.5. Gun occurs in version of fixed or swivel connection for installations. Housing material: high-strength plastic. Working pressure: up to 220 bar. pressure The permissible: 250 bar. Flow rate: 30 l/min. Operating temperature: up to +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWater gun for industry food. made with brass and steel stainless, sealing – Viton. Gun coated blue, non-staining, resistant to impact plastic, equipped in rings protective with soft rubber. has adjustable nozzle outlet, smooth adjustment flow and lock trigger. Bow cover trigger protects against uncontrolled opening stream water and against damage. maximum Working pressure: 24 bar. Maximum Operating temperature: +60°C (momentarily +90°C). Flow rate: 68 l/min (5 bar), max. 100 l/min.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCover for an IBC container IBC with an air vent with a thread internal pod air vent BSP. The cover is supplied with a gasket. Material: polypropylene. Sealing: EPDM. Operating temperature: from -10°C to +70°C (momentarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPneumatic extension - ready rubber line for air made with hose MPX20. terminated brass socket and a plug quick coupling Eurostandard DN7.2 (matches for typical connections). Do use general, in particular for tools pneumatic, tam where required is hose rubber o properties antistatic. Inner layer: black EPDM rubber. Reinforcement: textile braid. Outer layer: black EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsIndustrial hose for water and air. Widely used for washing hot water floors and equipment industrial. is suitable also for use external. resistant to conditions atmospheric, ozone and abrasion. Not is resistant to oil, not recommended also for air with mist oil. Inner layer: black EPDM rubber. Reinforcement: a polyester braid. Outer layer: red EPDM rubber. Working pressure: 10 bar. Operating temperature: od -40°C up to +100°C (momentarily up to 120°C).
