Is the 90Â° angle tube end, carbon steel, type RBS compatible with low-pressure rubber and textile-reinforced plastic hoses with external steel braid?

Yes. The 90Â° angle tube end, carbon steel, type RBS Format is compatible with low-pressure rubber and textile-reinforced plastic hoses with an external steel braid. It is specifically designed for low-pressure rubber and non-reinforced or textile-reinforced plastic hoses that have an external steel braid, and is commonly used in flexible conduits for sanitary fittings, fuel systems, air systems, etc. The carbon steel, galvanized construction provides suitable strength and corrosion protection for these applications.

Can the 90Â° angle tube end, carbon steel, type RBS be used in sanitary, fuel and air flexible conduit applications?

Yes. The 90Â° angle tube end, carbon steel, type RBS Format can be used in sanitary, fuel and air flexible conduit applications. It is designed for low-pressure rubber, non-reinforced and textile-reinforced plastic hoses with an external steel braid, and is commonly used in flexible conduits for sanitary fittings, fuel systems and air systems. Material: carbon steel, galvanized - suitable for those typical low-pressure service conditions; confirm compatibility with fluid, pressure, temperature and any sanitary standards for your specific application before installation.

Does the 90Â° angle tube end, carbon steel, type RBS require specific hose inner diameter tolerances for a secure fit?

Yes. The 90Â° angle tube end, carbon steel, type RBS requires appropriate hose inner diameter (ID) tolerances to ensure a secure, leak-free fit. especially because it is a no-nut fitting intended for low-pressure rubber and non-reinforced or textile-reinforced plastic hoses with an external steel braid. Key points: - Matching ID: The hose inner diameter must closely match the tube barb/shaft diameter of the RBS fitting. Too large an ID will slip and leak; too small an ID can tear the hose or prevent proper assembly. - Interference fit: A light interference (hose ID slightly smaller than the barb) is typically needed so the hose stretches over the fitting and grips the barb grooves or knurling. The exact interference tolerance depends on hose material and wall thickness; rubber hoses normally tolerate greater stretch than stiffer plastics. - Material considerations: Rubber and textile-reinforced plastic hoses require different tolerances. rubber can accept higher interference, non-reinforced plastics need closer control. The external steel braid does not secure the hose to the fitting internally, so ID fit is critical. - Low-pressure application: Because the RBS is for low-pressure systems, reliance on hose elasticity and possibly clamps is common. Even with correct ID, using an appropriate clamp or crimp (if compatible) improves safety and prevents blow-off under transient pressure. - Assembly practice: Heat or lubricant may be used to ease installation if the interference is tight. Ensure the hose covers the full barb length and seats against the fitting shoulder. - Recommendation: Follow the hose manufacturerâs recommended ID tolerance for barbed fittings and verify the tube endâs barb diameter. If in doubt, select hose ID equal to the nominal barb size or slightly undersized per manufacturer guidelines, and use a clamp suitable for the service to ensure a secure joint. In summary: correct hose ID tolerance relative to the RBS barb is essential for a secure fit; choose tolerances based on hose material and use a clamp for added security in low-pressure systems.

Angled tube fitting 90°, carbon steel, type RBS

All products, Low-pressure fittings and adapters/

Additional information

Material	CS – steel (cast iron)

Angled tube fitting 90° type RBS, without a nut, intended for low-pressure rubber and plastic hoses, unreinforced and with textile reinforcement, with an external steel braid. Commonly used in flexible lines for sanitary fittings, fuel and air installations, etc. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
EC-108304	Fitting tube 90° RBS 4 mm (hose 4.5 mm)	4	30	In stock	Enquiry
EC-108305	Fitting tube 90° RBS 5 mm (hose 5.5 mm)	5	30	In stock	Enquiry
EC-108306	Fitting tube 90° RBS 6 mm (hose 5.5 mm)	6	30	In stock	Enquiry
EC-108308	Fitting tube 90° RBS 8 mm (hose 7.5 mm)	8	30	In stock	Enquiry
EC-108310	Fitting tube 90° RBS 10 mm (hose 9 mm)	10	30	In stock	Enquiry
EC-108312	Fitting tube 90° RBS 12 mm (hose 11.5 mm)	12	30	In stock	Enquiry
EC-108315	Fitting tube 90° RBS 15 mm (hose 14.5 mm)	14	30	In stock	Enquiry
EC-108318	Fitting tube 90° RBS 18 mm (hose 17 mm)	18	30	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Angled tube fitting 90° type RBS, without a nut, intended for low-pressure rubber and plastic hoses, unreinforced and with textile reinforcement, with an external steel braid. Commonly used in flexible lines for sanitary fittings, fuel and air installations, etc. Material: carbon steel, galvanized.