Is the WE-MT angle screw connection, carbon steel, zinc-nickel compatible with anaerobic thread sealants instead of PTFE tape?

Yes . the WE-MT angle screw connection, carbon steel, zinc-nickel is compatible with anaerobic thread sealants as an alternative to PTFE tape. The product description explicitly states that the seal can be achieved âon the thread â with Teflon tape or anaerobic sealant.â Practical notes: - Compatibility: Use an anaerobic sealant formulated for metal fittings and steel threads. Ensure the sealant is suitable for the fluid media, pressure and temperature conditions of your system. - Application: Clean threads of oil, grease and debris before applying. Apply sealant according to manufacturer instructions, allow proper cure time before pressurizing. - Performance: Anaerobic sealants typically provide reliable, vibration-resistant, leak-proof seals and can prevent thread galling; PTFE tape remains a valid alternative for ease of use and reusability. - Surface coating: The zinc-nickel coating (6â10 Âµm, high corrosion resistance) on the fitting is not a barrier to using anaerobic sealants on the threads, but avoid sealants that could chemically attack the coating or plating under your operating conditions. Always verify the chosen sealantâs chemical compatibility and temperature/pressure ratings for your specific application.

Can the WE-MT angle screw connection, carbon steel, zinc-nickel be safely used with PTFE tape instead of anaerobic sealant?

Yes - the WE-MT angle screw connection, carbon steel, zinc-nickel can be used with PTFE (Teflon) tape instead of anaerobic sealant, provided the sealing instruction in the description is followed: the DIN 2353 WE-MT fitting specifies thread sealing on the thread with either Teflon tape or anaerobic sealant. Ensure correct application of PTFE tape (wrap in thread direction, 2â3 wraps, avoid tape entering the port) and tighten to recommended torque for the LL/L/S series to maintain mechanical integrity and leak-free performance. For high-pressure, dynamic, or critical applications, verify manufacturer torque/specs and consider anaerobic sealant if additional sealing reliability is required.

Can the WE-MT angle screw connection, carbon steel, zinc-nickel withstand repeated assembly/disassembly without sealant degradation?

Generally no. repeated assembly/disassembly of the WE-MT angle screw connection, carbon steel, zinc-nickel will tend to degrade threaded seals if they rely on Teflon tape or typical anaerobic sealants, unless specific precautions and correct products/procedures are used. Explanation and practical guidance: - Seal type: The WE-MT design specifies sealing on the external metric thread and allows Teflon tape or anaerobic sealant. Both work well for initial assemblies but behave differently under repeated cycles. - Teflon tape: Mechanical wear and loss of tape during disassembly mean you must reapply tape each time; reused tape will not reliably seal and can shred, contaminate the threads or create leaks. - Anaerobic sealants: Many permanent anaerobic adhesives cure to a hard film that is difficult to remove; repeated disassembly typically destroys the cured seal at the interface and requires full cleaning and reapplication. Some low-strength or removable threadlockers exist but still require reapplication after each breakdown. - Coating and threads: The zinc-nickel coating (6â10 Âµm) gives very high corrosion resistance, helping protect the underlying carbon steel during multiple cycles. However, mechanical wear from repeated assembly can damage the coating on threads, increasing risk of corrosion or galling over many cycles. - Series and materials: LL/L/S series (very light to heavy) influence mechanical robustness; heavier series tolerate more mechanical stress, but sealing behavior remains governed by the chosen sealant. - Best practice: If frequent disassembly is required, use a removable/replaceable sealing method: use fresh PTFE tape or a removable anaerobic sealant each time; ensure proper cleaning of threads and mating surfaces; avoid over-torquing to reduce coating damage; consider reusable mechanical seals (O-rings or gasket-style fittings) or fittings designed for repeated service rather than thread-sealed connections. - Conclusion: The WE-MT angle screw connection, carbon steel, zinc-nickel can survive many mechanical cycles thanks to its robust coating and material, but sealing performance will degrade unless seals are renewed or a service-friendly sealing method is used.

WE-MT angle screw connection, carbon steel, zinc-nickel

Additional information

Material	CS – steel (cast iron)

DIN 2353 angular screw fitting, type WE-MT: 24° DIN 2353 socket with external metric thread and external metric thread (seal on the thread – with Teflon tape or anaerobic sealant). Available as: LL (very light series), L (light series), S (heavy series). Surface coated with zinc-nickel with a layer thickness of 6-10 µm, characterized by very high corrosion resistance (up to 720 hours without corrosion in a salt spray chamber). Material: carbon steel, zinc-nickel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HD-WE-04LL-MT-08-CN	DIN 2353 fitting WE 4LL M8x1, Zn-Ni	-	100	In stock	Enquiry
HD-WE-06L-MT-10-CN	DIN 2353 fitting WE 6L M10x1, Zn-Ni	-	315	In stock	Enquiry
HD-WE-06LL-MT-06-CN	DIN 2353 fitting WE 6LL M6x1, Zn-Ni	-	100	In stock	Enquiry
HD-WE-06LL-MT-08-CN	DIN 2353 fitting WE 6LL M8x1, Zn-Ni	-	100	In stock	Enquiry
HD-WE-06LL-MT-10-CN	DIN 2353 fitting WE 6LL M10x1, Zn-Ni	-	100	In stock	Enquiry
HD-WE-06S-MT-12-CN	DIN 2353 fitting WE 6S M12x1.5, Zn-Ni	-	630	In stock	Enquiry
HD-WE-08L-MT-12-CN	DIN 2353 fitting WE 8L M12x1.5, Zn-Ni	-	315	In stock	Enquiry
HD-WE-08LL-MT-10-CN	DIN 2353 fitting WE 8LL M10x1, Zn-Ni	-	100	In stock	Enquiry
HD-WE-08S-MT-14-CN	DIN 2353 fitting WE 8S M14x1.5, Zn-Ni	-	630	In stock	Enquiry
HD-WE-10L-MT-14-CN	DIN 2353 fitting WE 10L M14x1.5, Zn-Ni	-	315	In stock	Enquiry
HD-WE-10S-MT-16-CN	DIN 2353 fitting WE 10S M16x1.5, Zn-Ni	-	630	In stock	Enquiry
HD-WE-12L-MT-16-CN	DIN 2353 fitting WE 12L M16x1.5, Zn-Ni	-	315	In stock	Enquiry
HD-WE-12L-MT-18-CN	DIN 2353 fitting WE 12L M18x1.5, Zn-Ni	-	315	In stock	Enquiry
HD-WE-12S-MT-18-CN	DIN 2353 fitting WE 12S M18x1.5, Zn-Ni	-	630	In stock	Enquiry
HD-WE-14S-MT-20-CN	DIN 2353 fitting WE 14S M20x1.5, Zn-Ni	-	630	In stock	Enquiry
HD-WE-15L-MT-18-CN	DIN 2353 fitting WE 15L M18x1.5, Zn-Ni	-	315	In stock	Enquiry
HD-WE-16S-MT-22-CN	DIN 2353 fitting WE 16S M22x1.5, Zn-Ni	-	400	In stock	Enquiry
HD-WE-18L-MT-22-CN	DIN 2353 fitting WE 18L M22x1.5, Zn-Ni	-	315	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

DIN 2353 angular screw fitting, type WE-MT: 24° DIN 2353 socket with external metric thread and external metric thread (seal on the thread – with Teflon tape or anaerobic sealant). Available as: LL (very light series), L (light series), S (heavy series). Surface coated with zinc-nickel with a layer thickness of 6-10 µm, characterized by very high corrosion resistance (up to 720 hours without corrosion in a salt spray chamber). Material: carbon steel, zinc-nickel.