Is the XFIGHT 5000 R13 MSHA hydraulic hose compatible with standard EN 856 R13 fittings and recommended for temperatures up to +125Â°C temporarily?

Yes. XFIGHT 5000 R13 MSHA hydraulic hose conforms to EN 856 R13 (also SAE 100 R13 and ISO 3862-1 R13), so it is compatible with standard EN 856 R13 fittings. Its specified operating temperature range is â40Â°C to +121Â°C with a temporary allowance up to +125Â°C, so short-term use at +125Â°C is within the manufacturerâs stated limits. Ensure fittings and assembly materials (seals, ferrules) used also tolerate the temporary higher temperature and that installation follows applicable safety and pressure guidelines.

Does the XFIGHT 5000 R13 MSHA hydraulic hose maintain full performance after 1,000,000 impulse cycles?

Yes. The XFIGHT 5000 R13 MSHA hydraulic hose demonstrated an enhanced lifespan confirmed by a 1,000,000 impulse cycle test, indicating it maintains required performance under that demanding endurance test. Its construction (oil-resistant inner/outer rubber, four-layer steel-wire reinforcement - six layers for DN32âDN38), MSHA flame-resistant outer layer, and compliance with EN 856 R13 / SAE 100 R13 / ISO 3862-1 R13 support continued reliable operation at specified working pressures (350â380 bar) and temperatures (â40Â°C to +121Â°C, momentarily +125Â°C).

Can the XFIGHT 5000 R13 MSHA hydraulic hose be used safely in applications requiring a 50% smaller bending radius than standard?

Yes. XFIGHT 5000 R13 MSHA hydraulic hose can be used safely in applications requiring a 50% smaller bending radius than standard. The product description explicitly states it is a general-purpose hydraulic hose with increased flexibility, offering a bending radius 50% better than standard. Key points supporting safe use: - Designed for reduced bending radius: Manufacturer specifies 50% improved bending radius versus standard R13 hoses, so it meets the dimensional/flexibility requirement. - Construction suited for demanding service: Four reinforcement steel wire layers (six layers for DN 32âDN 38) and oil-resistant synthetic rubber inner/outer layers provide strength and fluid compatibility. - Pressure and temperature ratings: Working pressures from 350 to 380 bar (depending on diameter) and operating temperature range â40Â°C to +121Â°C (temporarily +125Â°C) indicate suitability for high-pressure hydraulic systems under typical thermal conditions. - Durability confirmed: Life expectancy enhanced vs. standard, validated by 1,000,000 impulse cycle testing, reducing risk of premature failure when flexed repeatedly. - Safety standard compliance: Meets EN 856 R13, SAE 100 R13, ISO 3862-1 R13 and has an MSHA flame-resistant outer layer for added safety in hazardous environments. Caveat: Verify specific hose diameter (DN) bending radius value in manufacturer datasheet and ensure system installation respects minimum bend radius, pressure, temperature, and end-fitting compatibility. If fittings or routing impose tighter bends than the hoseâs rated minimum for a given DN, consult the manufacturer or technical data for confirmation.

XFIGHT 5000 R13 MSHA hydraulic hose

All products, Hydraulic rubber hoses/

Additional information

Material	synthetic rubber
Maximum operating temperature [°C]	121
Minimum operating temperature [°C]	-40

General-purpose hydraulic hose with increased flexibility (bending radius 50% better than standard). Enhanced hose lifespan compared to standard confirmed by a test of 1,000,000 impulse cycles. Outer layer flame-resistant (MSHA). Standards: EN 856 R13, SAE 100 R13, ISO 3862-1 R13. Inner layer: black, oil-resistant synthetic rubber. Reinforcement: four layers of steel wire (six for DN 32 ÷ DN 38). Outer layer: black, oil-resistant synthetic rubber. Working pressure: from 350 bar to 380 bar depending on hose diameter. Operating temperature: from -40°C to +121°C (temporarily +125°C).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
HW-R13-XFGT-19	Hydraulic hose XFIGHT 5000 R13 3/4" MSHA	20	380	In stock	Enquiry
HW-R13-XFGT-25	Hydraulic hose XFIGHT 5000 R13 1" MSHA	25	350	In stock	Enquiry
HW-R13-XFGT-32	Hydraulic hose XFIGHT 5000 R13 1.1/4" MSHA	32	350	In stock	Enquiry
HW-R13-XFGT-38	Hydraulic hose XFIGHT 5000 R13 1.1/2" MSHA	38	350	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

General-purpose hydraulic hose with increased flexibility (bending radius 50% better than standard). Enhanced hose lifespan compared to standard confirmed by a test of 1,000,000 impulse cycles. Outer layer flame-resistant (MSHA). Standards: EN 856 R13, SAE 100 R13, ISO 3862-1 R13. Inner layer: black, oil-resistant synthetic rubber. Reinforcement: four layers of steel wire (six for DN 32 ÷ DN 38). Outer layer: black, oil-resistant synthetic rubber. Working pressure: from 350 bar to 380 bar depending on hose diameter. Operating temperature: from -40°C to +121°C (temporarily +125°C).