Can the Short sheet sleeve for crimping low-pressure hoses, carbon steel, type H be used with steel-braided hoses and what maximum hose diameter (D2) and front hole size (D3) are recommended?

Short sheet sleeve for crimping low-pressure hoses, carbon steel, type H can be used with steel-braided hoses (e.g., type PZ), provided the hose material and braid allow deformation by this clamp and operating pressure is within lowâpressure range (up to â30 bar depending on diameter). Select the sleeve internal diameter (D2) to match the hose external diameter. Ensure the front hole diameter (D3) matches the mating end fitting. Specific recommended values: choose D2 equal to the hose outside diameter; choose D3 equal to the outer diameter of the used end/insert so the fitting passes cleanly through the sleeve front. If exact numeric sizes are needed, supply the hose outside diameter and the end type to determine the correct D2 and D3.

Can Short sheet sleeve for crimping low-pressure hoses, carbon steel, type H be crimped onto steel-braided hoses and what are the max D2 and D3 sizes recommended?

Short sheet sleeve for crimping low-pressure hoses, carbon steel, type H can be crimped onto steel-braided hoses (e.g., PZ type) provided the hose construction and braid allow deformation by the sleeve and the hose is within lowâpressure limits (up to â30 bar depending on diameter). Choose the sleeve internal diameter D2 to match the hose external diameter and ensure the front hole diameter D3 matches the hose end used (NiTO, quick coupling, etc.). Maximum recommended D2 and D3 are not explicitly given in the description - select the largest D2 that equals the hose OD and a D3 that fits the end; verify compatibility with manufacturer limits for steelâbraided hoses and max pressure for the specific diameter.

Can Short sheet sleeve for crimping low-pressure hoses, carbon steel, type H be used on NiTO or quick coupling ends and what D2 and D3 sizes suit these ends?

Yes. Short sheet sleeve for crimping low-pressure hoses, carbon steel, type H can be used on NiTO and quick coupling ends. Choose the sleeve by matching two dimensions: - D2 (internal diameter): select to match the hose external diameter. - D3 (hole diameter): must match the front hole diameter of the NiTO or quick coupling end to be fitted. Typical guidance: - Use sleeves for low-pressure hoses up to ~30 bar (depending on hose diameter) and for hose materials that are sufficiently soft (rubber with textile reinforcement, PVC; steel-braided hoses such as type PZ are also possible). - Material of sleeve: carbon steel, galvanized. Measure the hose O.D. for D2 and the coupling bore for D3; order the sleeve size where D2 â hose O.D. and D3 equals the coupling hole diameter.

Short sheet sleeve for crimping low-pressure hoses, carbon steel, type H

All products, Low-pressure fittings and adapters/

Additional information

Material	CS – steel (cast iron)

H-type crimping sleeve used for clamping hoses on ends without a locking mechanism connecting the sleeve to the end. It can also be used on NiTO ends and quick coupling ends. Low-pressure hoses up to approximately 30 bar (depending on diameter) made from various materials can be used with crimping sleeves, provided that the hose material is sufficiently soft for this type of clamp. Primarily rubber hoses with textile reinforcement and PVC hoses. There is also the possibility of crimping hoses with a steel braid (e.g., type PZ hose). The internal diameter of the sleeve should be selected according to the external diameter of the hose, while ensuring that the diameter of the hole at the front of the sleeve matches the used end. Diameter D2 [mm] – internal diameter. Diameter D3 [mm] – hole diameter. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
EC-104082	Sleeve H 8/12.5	12	-	In stock	Enquiry
EC-104084	Sleeve H 8/14	14	-	In stock	Enquiry
EC-104106	Sleeve H 10/15/16	16	-	In stock	Enquiry
EC-104121	Sleeve H 12/20/20	20	-	In stock	Enquiry
EC-104158	Sleeve H 12/22/20	22	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

H-type crimping sleeve used for clamping hoses on ends without a locking mechanism connecting the sleeve to the end. It can also be used on NiTO ends and quick coupling ends. Low-pressure hoses up to approximately 30 bar (depending on diameter) made from various materials can be used with crimping sleeves, provided that the hose material is sufficiently soft for this type of clamp. Primarily rubber hoses with textile reinforcement and PVC hoses. There is also the possibility of crimping hoses with a steel braid (e.g., type PZ hose). The internal diameter of the sleeve should be selected according to the external diameter of the hose, while ensuring that the diameter of the hole at the front of the sleeve matches the used end. Diameter D2 [mm] – internal diameter. Diameter D3 [mm] – hole diameter. Material: carbon steel, galvanized.