Can the T-piece with SPEEDFIT water separator, plastic for 22 mm pipe withstand continuous operation at 10 bar and +23Â°C, and 7 bar at +70Â°C?

Yes. The T-piece with SPEEDFIT water separator, plastic for 22 mm pipe is rated for continuous operation at a working pressure of 10 bar at +23Â°C and 7 bar at +70Â°C. Its specified operating temperature range is -20Â°C to +70Â°C, so running at +23Â°C and +70Â°C within those pressures falls within the productâs stated limits. Ensure installation and system conditions (e.g., pressure spikes, chemical exposure, and correct fittings) also comply with manufacturer guidelines to maintain safety and longevity.

Is the T-piece with SPEEDFIT water separator, plastic for 22 mm pipe suitable for intermittent pressure spikes above 10 bar?

No. The T-piece with SPEEDFIT water separator, plastic is rated for a maximum continuous working pressure of 10 bar at +23Â°C (7 bar at +70Â°C). Intermittent pressure spikes above 10 bar exceed its specified working pressure and risk damage or failure. Do not use it where pressures can intermittently exceed 10 bar; select a fitting with an appropriate higher pressure rating or install pressure-limiting measures.

Does the T-piece with SPEEDFIT water separator, plastic for 22 mm pipe require periodic maintenance to ensure 10 bar performance?

Yes. periodic maintenance is recommended to ensure the T-piece with SPEEDFIT water separator, plastic for 22 mm pipe continues to perform reliably at 10 bar. Reasoning and practical steps: - Purpose: The water separator removes condensate and particulates that can accumulate and reduce flow or cause internal wear. Left unchecked, blockages or saturation can compromise performance, especially under higher pressures and temperatures. - Inspection frequency: Inspect visually and functionally at regular intervals based on system usage. For typical compressed air systems a good starting point is monthly visual checks and quarterly functional checks; increase frequency in dirty or high-condensate environments. - What to check: - External condition of the T-piece and SPEEDFIT connections for cracks, deformation or leaks. - Tightness and integrity of the push-fit connections. - Drainage effectiveness of the separator; ensure condensate is being removed and not accumulating. - Signs of internal contamination or blockage (reduced flow, pressure drops downstream). - Maintenance actions: - Drain condensate and clean separator catchment according to system downtime windows. - Flush the line if particulate buildup is suspected. - Replace the separator element or the entire T-piece if damaged, cracked, or if performance cannot be restored by cleaning. - Re-test system pressure and check for leaks after reassembly. - Temperature considerations: Note the specified working pressures: 10 bar at +23Â°C and reduced to 7 bar at +70Â°C. Ensure the operating temperature does not approach the upper limit for prolonged periods, as higher temperatures reduce allowable pressure margin and may increase need for inspections. Following a routine inspection and maintenance schedule tailored to your operating conditions will help maintain the T-piece with SPEEDFIT water separator, plastic for 22 mm pipe at safe and reliable 10 bar performance.

T-piece with SPEEDFIT water separator, plastic

All products, Pneumatic piping systems/

Additional information

Material	P – material (plastic)

Tee with water separator for the SPEEDFIT system used in compressed air installations, for an outer pipe diameter of 22 mm. Material: plastic. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: from -20°C to +70°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
JG-PMTT22E	Water separator 22 mm	-	10	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Tee with water separator for the SPEEDFIT system used in compressed air installations, for an outer pipe diameter of 22 mm. Material: plastic. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: from -20°C to +70°C.