Can the SPEEDFIT screw-on spigot with female thread, brass be used with both plastic and metal (copper, brass, aluminum) compressed air pipes at 10 bar and up to 70Â°C?

Yes. The SPEEDFIT screw-on spigot with female thread, brass is designed for compressed air systems and can be used with both plastic and metal pipes (copper, brass, aluminum). Its working limits are 10 bar at +23Â°C and 7 bar at +70Â°C, with an operating temperature range of -20Â°C to +70Â°C. Therefore it is suitable for use at 10 bar provided the operating temperature is around ambient (â+23Â°C); at higher temperatures (approaching +70Â°C) the maximum allowable pressure falls to 7 bar, so it should not be used at 10 bar when system temperature reaches +70Â°C.

Is the SPEEDFIT screw-on spigot with female thread, brass compatible with different thread sealants for compressed air systems?

Yes. The SPEEDFIT screw-on spigot with female thread, brass is compatible with common thread sealants used in compressed air systems, provided they are suitable for brass and the stated operating conditions (working pressure up to 10 bar at +23Â°C, 7 bar at +70Â°C; temperature range â20Â°C to +70Â°C). Use sealants that are approved for compressed air (PTFE tape or anaerobic pipe thread sealants rated for metal fittings) and avoid sealants that can degrade brass or leave compressible residues that might leak under pressure. Apply sealant only to the male thread, assemble per manufacturer torque recommendations, and test the joint at working pressure before service.

Does the SPEEDFIT screw-on spigot with female thread, brass require specific pipe insertion depth for a secure compressed air connection?

Yes. the SPEEDFIT screw-on spigot with female thread, brass does require correct pipe insertion depth for a secure compressed air connection. Although the product description emphasizes push-in coupling operation and compatibility with plastic and metal pipes, secure sealing and mechanical retention in any push-fit system depend on fully inserting the pipe to the correct depth so the pipe engages the internal Oâring and gripping mechanism. Practical points: - Insert the pipe until it bottoms out against the internal shoulder; partial insertion can cause leaks or pullâout under pressure (working pressure up to 10 bar at +23Â°C). - For metal pipes (copper, brass, aluminum), ensure the cut is square, deburred and free of deformation so it reaches the correct depth. - For plastic pipes, ensure they are pushed home without collapsing the end; use a marker to indicate insertion depth if needed. - After insertion, give a firm pull to verify the pipe is retained. If you need exact insertion depths or a dimensioned diagram, consult the manufacturerâs technical datasheet or installation guide for the specific SPEEDFIT screw-on spigot with female thread, brass model.

SPEEDFIT screw-on spigot with female thread, brass

All products, Pneumatic piping systems/

Additional information

Material	B – brass (bronze)

Internal threaded fitting for the SPEEDFIT system used in compressed air installations. The installation can be made using plastic or metal pipes (copper, brass, aluminum). By pushing the fitting into the coupling, we obtain the possibility of connecting to the installation with an internal thread. Material: brass. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: from -20°C to +70°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
JG-MM501514N	Screwed stub 15 mm x 1/2" BSP	-	10	In stock	0 zł		Enquiry
JG-MM502216N	Screwed stub 22 mm x 3/4" BSP	-	10	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Internal threaded fitting for the SPEEDFIT system used in compressed air installations. The installation can be made using plastic or metal pipes (copper, brass, aluminum). By pushing the fitting into the coupling, we obtain the possibility of connecting to the installation with an internal thread. Material: brass. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: from -20°C to +70°C.