What are the recommended sealing materials and torque values for the T-piece "T" 1xGZ BSPT/2xGW BSP, stainless steel, type 62440, at pressures up to 140 bar and temperatures -20Â°C to +225Â°C?

For the T-piece "T" 1xGZ BSPT/2xGW BSP, stainless steel, type 62440 (AISI 316L) designed for -20Â°C to +225Â°C and up to 140 bar, recommended sealing materials and torque values are: Sealing materials: - PTFE tape (suitable for BSPT male thread): use virgin PTFE tape rated for high temperature/pressure (â200Â°C to +260Â°C). Use proper wrap technique to avoid overfilling the thread. - PTFE thread sealant paste (low-friction, anaerobic-free): compatible with AISI 316L and the media; temperature range to at least +225Â°C. - For metal-to-metal or high-pressure sealing on BSP female ports, consider using bonded PTFE or spiral-wound/metallic gasket inserts if specified by mating fittings. - O-rings (if fittings use O-ring face seals): FKM/Viton for up to +225Â°C (limited near upper end), or perfluoroelastomer (FFKM) for best chemical and temperature resistance up to +260Â°C. Torque values (typical guidance for assembly of stainless steel BSP/BSPT connections; verify with mating fitting manufacturer): - 1/4" BSPT male into BSP female: 20â30 Nm - 3/8" BSPT: 30â45 Nm - 1/2" BSPT: 45â70 Nm - 3/4" BSPT: 70â100 Nm - 1" BSPT: 100â140 Nm Notes: - These torque ranges are general recommendations; final torque depends on thread size, lubrication/sealant used, and material condition. Apply torque incrementally and verify leak-tightness with appropriate pressure testing at working conditions. - Avoid over-torquing stainless steel fittings to prevent galling; use anti-seize or suitable lubricant on threads where recommended.

How should the T-piece "T" 1xGZ BSPT/2xGW BSP, stainless steel, type 62440 be installed to ensure leak-free performance at up to 140 bar and -20Â°C to +225Â°C?

Install the T-piece "T" 1xGZ BSPT/2xGW BSP, stainless steel, type 62440 as follows to ensure leak-free performance up to 140 bar and -20Â°C to +225Â°C: 1. Inspect threads and sealing faces for damage and cleanliness. Use compatible AISI 316L fittings only. 2. For the 1x external BSPT (tapered) thread, apply appropriate PTFE tape or approved thread sealant for high-pressure service; tighten to recommended torque for BSPT taper engagement until proper seal is achieved. 3. For the 2x internal BSP (parallel) threads, fit mating BSP parallel male fittings with correct flat gasket, Oâring or bonded washer as specified by the mating part; do not rely on thread sealing alone. 4. Assemble using correct torque values to avoid overstressing the part; support piping to prevent bending loads on the tee. 5. Test assembly at working pressure (hydrostatic or pneumatic per applicable standard) and inspect at operating temperature extremes if possible. 6. Use compatible fluids and avoid corrosive media outside AISI 316L resistance.

Can the T-piece "T" 1xGZ BSPT/2xGW BSP, stainless steel, type 62440 be used with aggressive media at -20Â°C to +225Â°C and 140 bar?

Based on the provided description, the T-piece "T" 1xGZ BSPT/2xGW BSP, stainless steel, type 62440 is made of AISI 316L stainless steel, has an operating temperature range of -20Â°C to +225Â°C and a working pressure of 140 bar. These specifications indicate that the component is mechanically rated for the stated temperature and pressure limits. However, suitability for aggressive media cannot be guaranteed solely from these general data. AISI 316L offers good corrosion resistance to many chemicals and chloride-bearing environments, but compatibility depends on the specific aggressive media (chemical composition, concentration), temperature, pressure, and exposure duration. Some strong acids, alkalis, oxidizers (e.g., concentrated hydrochloric acid, sulfuric acid at elevated temperatures, hot chlorides, molten salts, or certain halogenated solvents) and halogen-containing or fluoride-containing media can attack 316L. Also consider potential for stress corrosion cracking, pitting, crevice corrosion, and corrosion under pressure/temperature conditions. Recommendation: Verify chemical compatibility of AISI 316L with the exact aggressive media at the operating temperature and pressure using chemical compatibility charts or corrosion data, or consult the material supplier/manufacturer for compatibility confirmation. If uncertainty remains, consider higher-alloy materials (e.g., duplex stainless steels, Hastelloy) or lining/coating solutions.

T-piece “T” 1xGZ BSPT/2xGW BSP, stainless steel, type 62440

All products, Threaded pneumatic fittings/

Additional information

Material	SS – stainless steel

T-shaped stainless steel tee type 62440, 1x external BSPT thread and 2x internal BSP thread. Material: AISI 316L steel. Operating temperature: from -20°C to +225°C. Working pressure: 140 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AI-62440-02	T-shaped screw fitting GZ 1/8" BSPT / 2 x GW 1/8" BSP, AISI 316L	-	140	In stock	Enquiry
AI-62440-04	T-shaped screw fitting GZ 1/4" BSPT / 2 x GW 1/4" BSP, AISI 316L	-	140	In stock	Enquiry
AI-62440-06	T-shaped screw fitting GZ 3/8" BSPT / 2 x GW 3/8" BSP, AISI 316L	-	140	In stock	Enquiry
AI-62440-08	T-shaped screw fitting GZ 1/2" BSPT / 2 x GW 1/2" BSP, AISI 316L	-	140	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

T-shaped stainless steel tee type 62440, 1x external BSPT thread and 2x internal BSP thread. Material: AISI 316L steel. Operating temperature: from -20°C to +225°C. Working pressure: 140 bar.