Is the Thermoplastic double hose with aramid braid F2220 compatible with hydraulic oil, gases, air, fuels and water-based fluids across its full temperature and pressure range?

Thermoplastic double hose with aramid braid F2220 is designed for hydraulic oil installations, gases, air, fuels and water-based fluids and.within the limits specified.is compatible with those media. Its construction: polyester inner tube, double aramid braid reinforcement and microâperforated polyurethane outer layer meets standards SAE 100R8 / ISO 3949âR8. Working pressure ranges from 250 to 362 bar depending on diameter. Operating temperature range is â40Â°C to +93Â°C generally; for water and air the upper limit is +65Â°C. Important: compatibility depends on specific fluid formulations, concentrations and full operating conditions (pressure, temperature, additives). For critical applications confirm chemical compatibility and safety margins with the hose manufacturer or provide fluid details for verification.

Does Thermoplastic double hose with aramid braid F2220 require special fittings for high-pressure hydraulic oil and gas applications?

Thermoplastic double hose with aramid braid F2220 does not inherently require special fittings beyond those appropriate for highâpressure hydraulic and gas service. Because itâs rated to 250â362 bar and uses aramid braid reinforcement with thermoplastic inner/outer layers, use fittings that: - are rated for the hoseâs maximum working pressure and matched to the specific hose diameter, - are compatible with thermoplastic/polyurethane materials (to avoid chemical or abrasion issues), - provide secure crimping or mechanical attachment suitable for doubleâhose constructions or welded outer layers, - meet relevant standards for hydraulic/gas systems and sealing (e.g., SAE/ISO as applicable). For gas applications and critical highâpressure systems, consult the hose manufacturerâs recommended fittings and assembly procedure to ensure safety, correct swaging/crimp profiles, and compliance with regulations.

Can Thermoplastic double hose with aramid braid F2220 be used for potable water or only non-potable water-based fluids?

Thermoplastic double hose with aramid braid F2220 is designed for hydraulic oil, gases, air, fuels and water-based fluids, but the provided description does not explicitly state suitability for potable (drinking) water. Key points affecting potable use: - Materials: inner layer is polyester and reinforcement is aramid braid. Polyester is not typically certified food-contact by default; aramid fibers are not intended as food-contact materials and could present contamination risks if not encapsulated or specifically certified. - Outer layer: micro-perforated polyurethane. perforation suggests possible exchange with environment and is not compatible with potable-water hygiene requirements. - Standards listed (SAE 100R8, ISO 3949-R8) are hydraulic hose standards, not potable water or drinking-water approvals (e.g., NSF/ANSI 61, WRAS, KTW). - Temperature note: âfor water and air up to +65Â°Câ addresses performance but not sanitary safety. Conclusion: Thermoplastic double hose with aramid braid F2220 should be considered suitable only for non-potable water-based fluids unless the manufacturer provides explicit potable-water certifications (NSF/ANSI, WRAS, KTW or equivalent) and documentation that all materials and construction meet drinking-water safety. Request manufacturer certification if potable use is required.

Thermoplastic double hose with aramid braid F2220

All products, Thermoplastic hoses/

Additional information

Material	PEE – polyester
Maximum operating temperature [°C]	93
Minimum operating temperature [°C]	-40
Vacuum resistance	check

Lightweight, flexible hose in a double version (two hoses with a welded outer layer) designed for hydraulic oil installations, gases, air, fuels, water-based fluids. Standards: SAE 100R8, ISO 3949-R8. Inner layer: polyester. Reinforcement: double aramid braid. Outer layer: micro-perforated polyurethane. Working pressure: from 250 bar to 362 bar, depending on the hose diameter. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MC-F2220C-06	Thermoplastic hose F2220C 2x1/4"	6	362	In stock	Enquiry
MC-F2220D-08	Thermoplastic hose F2220D 2x5/16"	8	350	In stock	Enquiry
MC-F2220E-10	Thermoplastic hose F2220E 2x3/8"	10	300	In stock	Enquiry
MC-F2220F-13	Thermoplastic hose F2220F 2x1/2"	12	250	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Lightweight, flexible hose in a double version (two hoses with a welded outer layer) designed for hydraulic oil installations, gases, air, fuels, water-based fluids. Standards: SAE 100R8, ISO 3949-R8. Inner layer: polyester. Reinforcement: double aramid braid. Outer layer: micro-perforated polyurethane. Working pressure: from 250 bar to 362 bar, depending on the hose diameter. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).