Is the Two-part hose clamp with catches, US version, cast iron suitable for hoses operating up to 25 bar when installed with compatible fittings and hoses?

Yes. The Two-part hose clamp with catches, US version, cast iron is suitable for hoses operating up to 25 bar when used with compatible fittings and hoses and installed correctly. The product description states it is made of high-quality galvanized ductile cast iron with a locking mechanism for hose mounting and explicitly notes that with proper installation, appropriately selected hose, and fitting, a working pressure up to 25 bar is achievable. Ensure you verify the hose and fittingsâ pressure ratings, follow manufacturer installation instructions, and perform pressure testing as required for your application.

Does the Two-part hose clamp with catches, US version, cast iron resist corrosion after yellow passivation without hexavalent chromium?

Two-part hose clamp with catches, US version, cast iron Format: Yes - the product description indicates corrosion resistance. The clamp is made of galvanized ductile cast iron with yellow passivation explicitly free of hexavalent chromium. Galvanization plus a yellow (trivalent/hexavalentâchromiumâfree) passivation layer provides improved protection against rust compared with bare iron. However, longâterm performance depends on service conditions (humidity, salt exposure, mechanical damage to coating) and correct installation. With proper installation, suitable hose and fitting, and typical environments, the clamp will resist corrosion; in highly aggressive or marine environments additional protection or stainless alternatives may be advisable.

Can the Two-part hose clamp with catches, US version, cast iron be used for high-vibration applications without loosening?

The Two-part hose clamp with catches, US version, cast iron can be suitable for high-vibration applications, but only under certain conditions. Why it can work: - Construction: made of high-quality galvanized ductile cast iron, the clamp is robust and resistant to fatigue compared with brittle cast materials. - Locking mechanism: the connection to the hose part includes a locking mechanism (catches/hooks) that provides positive engagement and helps resist loosening from cyclic loads. - Pressure rating: when properly installed with a correctly matched hose and fitting, it is rated for working pressures up to 25 bar, indicating a secure seal under load. Limitations and required precautions: - Vibration resistance depends heavily on correct installation: ensure the clamp is properly seated, catches fully engaged, and torque/fit is per manufacturer guidance. - Hose and fitting choice is critical: use hoses and fittings designed for high-vibration service (compatible diameter, reinforcement, and sufficient stiffness). A soft or undersized hose can allow relative movement and promote loosening. - Supplementary measures: consider using anti-vibration mounts, safety wires, secondary clamps, or thread-locking/locking devices on adjacent fittings if vibration is severe. - Periodic inspection: in high-vibration environments, regular checks for deformation, wear, or loosening are recommended. Conclusion: The Two-part hose clamp with catches, US version, cast iron can be used in high-vibration applications without loosening if correctly selected and installed with compatible hose and fitting, and if additional vibration-mitigating measures and inspections are applied.

Two-part hose clamp with catches, US version, cast iron

Additional information

Material	CS – steel (cast iron)

Two-part clamp, USA version, with hooks (“claws”), made of high-quality ductile cast iron galvanized (with yellow passivation free of hexavalent chromium). Designed for hose mounting, with a connection to the hose part with a locking mechanism. Material: galvanized ductile cast iron. With proper installation, appropriately selected hose, and fitting, working pressure up to 25 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
LU-LB-10	Cast iron clamp 2-pc., type US, for hose 19 mm, range 38÷43 mm	-	-	In stock	Enquiry
LU-LB-4	Cast iron clamp 2-pc., type US, for hose 13 mm, range 21÷27 mm	-	-	In stock	Enquiry
LU-LB-9	Cast iron clamp 2-pc., type US, for hose 19 mm, range 33÷38 mm	-	-	In stock	Enquiry
LU-LBU-29	Cast iron clamp 2-pc., type US, for hose 50 mm, range 63÷70 mm	-	-	In stock	Enquiry
LU-LBU-9	Cast iron clamp 2-pc., type US, for hose 19 mm, range 30÷33 mm	-	-	In stock	Enquiry
LU-SKA-10	Cast iron clamp 2-pc., type US, for hose 25 mm, range 34÷45 mm	-	-	In stock	Enquiry
LU-SKA-34	Cast iron clamp 2-pc., type US, for hose 19 mm, range 30÷35 mm	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Two-part clamp, USA version, with hooks (“claws”), made of high-quality ductile cast iron galvanized (with yellow passivation free of hexavalent chromium). Designed for hose mounting, with a connection to the hose part with a locking mechanism. Material: galvanized ductile cast iron. With proper installation, appropriately selected hose, and fitting, working pressure up to 25 bar.