Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFPRI type check valve used in hydraulic systems as a component for closing the flow of hydraulic fluid in one direction and allowing free flow of fluid in the opposite direction. Designed to be screwed into a suitably deep threaded hole. Supplied with an O-ring, which serves as a seal between the valve and the threaded hole. The O-ring can be installed on either side of the valve (depending on the flow direction desired). Standard opening pressure: 0.5 bar. Permissible flow direction A → A1. Material: galvanized steel (body), hardened steel (stem). Sealing: NBR. Operating temperature: from -20°C to +100°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReduction socket connector of the STECKO system for use in hydraulic systems for mining. Material: automatic steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCEJN 115 quick coupling socket with external thread and valve designed for hydraulic installations at very high pressures. Used in hydraulic presses, rescue equipment, hydraulic lifts, cutters, etc. Optionally, the socket can be equipped with a safety ring to prevent accidental disconnection. Supplied standard with a cap for protection against contamination. Material: hardened, galvanized steel. Sealing: NBR. Flow: 6 l/min (Δp = 4 bar). Nominal diameter: 2.5 mm. Working pressure: 1000 bar (connected coupling). Burst pressure: 2600 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe R-4000 type check valve is designed and manufactured in accordance with the PED Directive 2014/68/EU. It is intended for high-pressure hydraulic and industrial installations. It closes the flow of medium in one direction and opens free flow of medium in the opposite direction. Standard opening pressure: 0.5 bar (also available in 1, 2, 3, and 5 bar). Permissible flow direction: A → A1. Material: galvanized steel, nickel-plated brass, stainless steel AISI 316L. Sealing: NBR - standard RA, RL; viton (FKM) - standard RZ; EPDM - option. Operating temperature: from -20°C to +100°C (NBR); from -20°C to +200°C (viton); from -40°C to +150°C (EPDM).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSTECKO socket elbow for use in hydraulic systems for mining. Material: automatic steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° Non-Skive Flare Fitting SAE 6000 (SFS 90), heavy series, designed for crimping in hoses type 4SP, 4SH, R13, and R15 using TI-N crimping sleeve... Installation: without cutting the hose rubber. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight INTERLOCK end with internal BSP thread, 60° cone with o-ring, for hose type 4SH, R13, and R15. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° flange connection with a compact design, featuring a flange with a pitch diameter of holes from 35 mm to 55 mm, with an external metric connection thread, socket 24° DIN 2353. Used in hydraulic pump connections. Standardly equipped with a set of screws, washers, and an O-ring. Material: carbon steel, galvanized. Operating temperature: from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-part insert for clamp DIN 3015 type 301 made according to standard DIN 3015. Standardly features a profiled (grooved) surface for the pipe opening. Insert material: self-extinguishing polyamide. Operating temperature: from -40°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWEO plug with hose end for use in hydraulic systems where there is not enough space to install the hose in the traditional way. Once connected, the plug has freedom of movement in the socket, which prevents the hoses from twisting during installation. Designed for hoses type 1SN, 2SN, 1SC, 2SC. Working pressure: 350 bar (for hose size up to 3/4"), 250 bar (for hose size 1"). Material: hardened steel. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality three-way ball valve "L" type BK3L with internal BSP thread, designed for high-pressure hydraulic installations. Material: steel (body, ball, stem). Seals: POM (ball), NBR (stem). Operating temperature: from -40°C to +100°C (POM); from -20°C to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdaptor with external BSP thread (sealing DIN 3852 type E - elastomeric seal with rectangular cross-section) and WEO socket for use in hydraulic systems; designed for easy connection of hydraulic hose terminated with WEO plug. Once connected, the plug has freedom of movement in the socket, preventing twisting of hoses during installation. Working pressure: 350 bar (for sizes up to 3/4"), 250 bar (for size 1"). Material: hardened steel. Operating temperature: from -30°C to +100°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / Details45° NON SKIVE end with internal BSP thread, with sealing on a 60° cone with an O-ring (DKOR 45), intended for crimping in hoses type 4SP, 4SH, R13, and R15 using crimping sleeve TI-N... . Installation: without cutting the hose rubber. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° INTERLOCK fitting with internal metric thread, 24° cone with o-ring, heavy series, for hose type 4SH, R13, and R15. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlanged connection 90° with a compact design, featuring a flange with a pitch diameter of holes from 26 mm to 72 mm, with internal BSP connection thread. Used in hydraulic pump connections. Standardly equipped with a set of screws, washers, and an O-ring. Material: carbon steel, galvanized. Operating temperature: from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic hose with an extended temperature working range compared to standard hoses. Standards: exceeds EN 853 1SN, ISO 1436-1SN, SAE 100R1-AT. Inner layer: black, oil-resistant synthetic rubber. Reinforcement: single steel braid. Outer layer: blue, oil-resistant synthetic rubber resistant to ozone and aging. Working pressure: from 40 bar to 225 bar depending on hose diameter. Operating temperature: from -50°C to +135°C (temporarily +150°C). For water and air, maximum operating temperature +70°C. For air above 17 bar, micro-perforation of the outer layer is required.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-part insert for clamp DIN 3015 type 201 made according to standard DIN 3015. Standardly features a profiled (grooved) surface for the pipe opening. Insert material: self-extinguishing polyamide. Operating temperature: from -40°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBlind plug for quick coupling coupling DNP series PVS. Material: steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality two-way ball valve type BKH with internal NPT thread, designed for high-pressure hydraulic and industrial installations. To properly select the valve for media other than hydraulic oil and for high operating temperatures, consultation with Tubes International is required. Working pressure depends on the sealing material of the valve. Material: steel (body, ball, stem). Seals: PA (ball), NBR (stem). Operating temperature: from -40°C to +100°C (PA); from -20°C to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReduction plug connector of the STECKO system for use in hydraulic systems for mining. Material: automatic steel, galvanized. Sealing: NBR (o-ring), Teflon (back-up ring).
- Select options This product has multiple variants. The options may be chosen on the product page / Details45° INTERLOCK SUPERCAT flange end, O-ring seal or other gasket in the flange groove, for hose types 4SH, R13, and R15. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlanged connection with a compact design featuring a flange with a pitch diameter of holes from 35 mm to 55 mm, with an external metric connection thread, socket 24° DIN 2353. Used in hydraulic pump connections. Standardly equipped with a set of screws, washers, and an O-ring. Material: carbon steel, galvanized. Operating temperature: from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality sapphire nozzle for high-pressure devices. Maximum working pressure: 3000 bar. Operating temperature: up to +150°C. Tightening torque [Nm]: max. 25.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPSAF clamping sleeve for UHP thermoplastic hoses. Diameter D1 [mm] - outer diameter. Diameter D2 [mm] - inner diameter. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGeneral-purpose hydraulic hose. Enhanced hose lifespan compared to the standard confirmed by a test of 1,000,000 impulse cycles. Outer layer is flame-resistant (MSHA). Standards: EN 856 4SP, ISO 3862-1 4SP. Inner layer: black, oil-resistant synthetic rubber. Reinforcement: four layers of steel wire. Outer layer: black, oil-resistant synthetic rubber. Working pressure: from 180 bar to 460 bar (depending on hose diameter). Operating temperature: from -40°C to +100°C (temporarily +120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-part insert clamp DIN 3015 type 101 manufactured according to DIN 3015 standard. For size group 0, there is one hole for a screw; for size groups 1 to 6, there are two holes for screws. It standardly features a profiled (grooved) surface for the pipe hole. Insert material: self-extinguishing polyamide. Operating temperature: from -40°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° WEO plug with hose end for use in hydraulic systems where there is not enough space to install the hose in the traditional way. After connection, the plug has freedom of movement in the socket, which prevents the hoses from twisting during installation. Designed for hoses type 1SN, 2SN, 1SC, 2SC. Working pressure: 350 bar (for hose size up to 3/4"), 250 bar (for hose size 1"). Material: hardened steel. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCEJN 116 quick coupling plug with external thread without valve intended for hydraulic installations at very high pressures. Used in hydraulic presses, rescue equipment, hydraulic lifts, cutters, etc. Supplied standard with a cap for protection against contamination. Material: hardened, galvanized steel. Flow: 6 l/min (Δp = 4 bar). Nominal diameter: 2.5 mm. Working pressure: 1500 bar (connected coupling). Burst pressure: 3000 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality two-way ball valve type SKH with BSP internal thread, designed for high-pressure hydraulic and industrial installations. To properly select the valve for media other than hydraulic oil and for high temperatures, please consult Tubes International. Working pressure depends on the sealing material of the valve. Material: steel (body, ball, stem). Seals: POM or PTFE (ball), NBR or FKM (stem). Operating temperature: from -40°C to +100°C (POM); from -200°C to +250°C (PTFE); from -20°C to +100°C (NBR); from -20°C to +200°C (FKM).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSTECKO socket-plug connector for use in hydraulic systems for mining. Material: automatic steel, galvanized. Sealing: NBR (o-ring), Teflon (back-up ring).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic end fitting (type P - with a special "tail" for thermoplastic hose) with external NPTF thread, sealing on the thread using Teflon tape or liquid sealant (AGN). Designed for crimping in UHP thermoplastic hoses using a crimping sleeve suitable for the hose type. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight ORFS INTERLOCK fitting with internal UNF thread, flat sealing, for hose type 4SH, R13, and R15. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug connector with locking nuts SKV for use in hydraulic systems. Material: galvanized steel. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLong bottom plate for mounting DIN 3015 standard clamp type 100/101. For size group 0, there is one hole for a screw. For size group 1 to 6, there are two holes for screws. Material: carbon steel, galvanized or AISI 316L steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket tee of the STECKO system for use in hydraulic systems for mining. Material: automatic steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic hose with an extended operating temperature range compared to standard hydraulic hoses. Confirmed hose lifespan of 300,000 impulse cycles. Standards: exceeds EN 853 1SN, ISO 1436-1SN, SAE 100R1S-AT. Inner layer: black, oil-resistant synthetic rubber. Reinforcement: single steel braid. Outer layer: blue, oil-resistant synthetic rubber resistant to ozone and aging. Working pressure: from 40 bar to 225 bar depending on hose diameter. Operating temperature: from -40°C to +135°C (temporarily +150°C). For water and air, maximum operating temperature +70°C. For air above 17 bar, micro-perforation of the outer layer is required.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBlind plug for quick coupling socket DNP series PVS. Material: aluminum.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-way ball valve type BKH L/S with external metric thread, DIN 2353, intended for high-pressure hydraulic installations. Available as: L (light series), S (heavy series). Material: steel (body, ball, stem). Seals: POM (ball), NBR (stem). Operating temperature: from -40°C to +100°C (POM); from -20°C to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic end fitting (type P - with a special "tail" for thermoplastic hose) with internal metric thread, sealing with an O-ring on a 24° cone (DKOS), heavy-duty series. Designed for crimping in UHP thermoplastic hoses using a crimping sleeve suitable for the hose type. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / Details45° INTERLOCK SAE 6000 flange end, O-ring seal or other gasket in the flange groove, for hose type 4SH, R13, and R15. Material: carbon steel, galvanized.
