Is the BANJO angle end 90Â°, carbon steel, type RBR compatible with textile-reinforced plastic hoses with an external steel braid?

Yes. The BANJO angle end 90Â°, carbon steel, type RBR is compatible with textile-reinforced plastic hoses with an external steel braid. It is specifically designed for low-pressure rubber and non-reinforced and textile-reinforced plastic hoses with an external steel braid, and is commonly used in flexible lines for sanitary fittings, fuel systems, air systems, etc. The carbon steel, galvanized construction suits these applications.

Can BANJO angle end 90Â°, carbon steel, type RBR be used in potable water or sanitary installations?

BANJO angle end 90Â°, carbon steel, type RBR Format: No - this fitting is not suitable for potable water or sanitary installations. It is designed for low-pressure rubber and non-reinforced/textile-reinforced plastic hoses with external steel braid and is commonly used for sanitary fittings, fuel and air systems, but its carbon steel (galvanized) construction and intended hose types do not meet potable water safety and corrosion resistance requirements. Galvanized carbon steel can leach zinc/iron, corrode in long-term water exposure, and lacks certification for drinking water. For potable/sanitary use choose fittings specified and certified for drinking water (e.g., stainless steel AISI 316 or approved brass with appropriate WRAS/ACS/NSF certifications).

Can BANJO angle end 90Â°, carbon steel, type RBR withstand vibration and movement in automotive fuel lines?

BANJO angle end 90Â°, carbon steel, type RBR Format: Given the described application (low-pressure rubber and non-reinforced/textile-reinforced plastic hoses with an external steel braid) and typical uses (flexible lines for sanitary fittings, fuel systems, air systems), this fitting can tolerate some vibration and movement but with important limitations. Why it can work: - Designed for flexible, low-pressure hoses: the RBR type accommodates hose flexing and minor movement. - Carbon steel, galvanized construction offers good mechanical strength and fatigue resistance for typical automotive low-pressure lines. - External steel braid on hose adds support against abrasion and limits hose expansion under pressure, helping retain seal under motion. Limitations and cautions: - Low-pressure rating: not suitable for high-pressure fuel injection systems. It is intended for low-pressure fuel lines only (gravity feed, return lines, vapor lines). Verify actual pressure rating for your system. - Vibration and continuous dynamic movement: repeated flexing, high-frequency vibration, or large angular movement can accelerate wear at the hose-ferrule interface, cause loosening of connections, or hose abrasion against fittings. Use appropriate clamps, routing, and strain relief. - Corrosion risk: galvanized carbon steel has protection but may corrode in harsh automotive environments (road salt, moisture, fuel additives). Consider corrosion-resistant alternatives (stainless steel) for long-term reliability. - Compatibility with fuels and temperatures: ensure hose and galvanization are compatible with fuel type (especially ethanol blends) and operating temperatures; otherwise degradation can occur. Recommendations: - Confirm system pressure and duty (static vs. dynamic). Use BANJO angle end 90Â°, carbon steel, type RBR Format only within rated pressure and temperature limits. - Use proper clamps and secure routing to minimize relative movement and vibration at the fitting. - For critical or high-pressure fuel applications, or harsh environments, choose fittings/hose assemblies rated for those conditions (stainless steel, reinforced hoses, or specific automotive-rated fittings). Conclusion: BANJO angle end 90Â°, carbon steel, type RBR Format can withstand vibration and movement in low-pressure automotive fuel lines if used within its pressure, temperature, and environmental limits and if installation includes proper routing and clamping; it is not suitable for high-pressure or highly dynamic fuel systems.

Angled BANJO fitting 90°, carbon steel, type RBR

All products, Low-pressure fittings and adapters/

Additional information

Material	CS – steel (cast iron)

Angled BANJO fitting 90° type RBR, intended for low-pressure rubber and plastic hoses, unreinforced and with textile reinforcement, with an external steel braid. Commonly used in flexible lines for sanitary fittings, fuel and air installations, etc. Material: carbon steel, galvanized.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
EC-108008	Fitting BANJO 90° RBR 8 mm (hose 5.5 mm)	5	30	In stock	Enquiry
EC-108010	Fitting BANJO 90° RBR 10 mm (hose 5.5 mm)	6	30	In stock	Enquiry
EC-108012	Fitting BANJO 90° RBR 12 mm (hose 7.5 mm)	8	30	In stock	Enquiry
EC-108014	Fitting BANJO 90° RBR 14 mm (hose 9 mm)	10	30	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Angled BANJO fitting 90° type RBR, intended for low-pressure rubber and plastic hoses, unreinforced and with textile reinforcement, with an external steel braid. Commonly used in flexible lines for sanitary fittings, fuel and air installations, etc. Material: carbon steel, galvanized.