Can the Ball end for hose - insert under nut, brass, type MU withstand continuous use at 12 bar and temperatures from -20Â°C to +100Â°C in industrial air systems?

Yes. Ball end for hose - insert under nut, brass, type MU is rated for industrial air use with a working pressure up to 12 bar and an operating temperature range of -20Â°C to +100Â°C, so when used within those limits it can withstand continuous service. Because the part is brass and specified for air installations, it is suitable for typical industrial air pressures and temperatures stated. Ensure the assembly (hose, nut, seals) and installation practices also match these ratings; any components downstream with lower pressure or temperature limits, aggressive media, or cyclic pressure/temperature extremes could reduce safe life. Regular inspection and correct tightening/installation will help maintain continuous operation at 12 bar and within -20Â°C to +100Â°C.

Is Ball end for hose - insert under nut, brass, type MU suitable for intermittent high-pressure pulses up to 12 bar in industrial air lines?

Yes. Ball end for hose - insert under nut, brass, type MU is suitable for intermittent high-pressure pulses up to 12 bar in industrial air lines. The product specification states use in industrial installations (e.g., air), brass construction, working pressure up to 12 bar and operating temperature â20Â°C to +100Â°C, which covers intermittent pulses at that pressure. Ensure correct installation, compatible hose and nut, and verify pulse frequency/amplitude and system safety margins for your specific application.

Does Ball end for hose - insert under nut, brass, type MU require special seals for oily or humid compressed air?

Ball end for hose - insert under nut, brass, type MU Format: Based on the provided description (brass material, intended for industrial installations such as air, working pressure up to 12 bar, temperature range â20 Â°C to +100 Â°C), standard units of this type do not inherently include special seals for aggressive oily or very humid compressed air. Brass bodies are compatible with general compressed air, but sealing performance depends on the seal material used (e.g., NBR, EPDM, FKM). - For oily compressed air: use oil-resistant seals such as NBR (nitrile) or FKM (Viton) to avoid swelling or deterioration from oil contact. NBR is common and cost-effective for mineral-oil-based lubricants; FKM offers better chemical and high-temperature resistance. - For humid or wet air: EPDM or NBR are typically suitable; EPDM has superior resistance to water and steam but poor resistance to oils. If both humidity and oil are present, choose a compromise like NBR or a specially formulated compound. - Temperature and pressure limits must be respected; ensure the selected sealâs temperature range fits within â20 Â°C to +100 Â°C and service pressure up to 12 bar. - If the product description did not specify seal material, confirm with the supplier/manufacturer which seal is installed or request oil-/moisture-resistant seals as needed. For critical or long-term oily/humid service, specify appropriate seal material at order or consider protective coatings and regular maintenance. Conclusion: Ball end for hose - insert under nut, brass, type MU Format may require special seals for oily or humid compressed airâselect oil- or water-resistant seal compounds (NBR, FKM, EPDM) based on the specific contamination and operating conditions and verify with the manufacturer.

Ball end for hose – insert under nut, brass, type MU

All products, Low-pressure fittings and adapters/

Additional information

Material	B – brass (bronze)

Ball end for hose – insert under the nut – for use in industrial installations, e.g., for air. Material: brass. Working pressure: up to 12 bar. Operating temperature: from -20°C to +100°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
MU-2895	Ball end - insert for 3/8" nut, 6 mm hose, brass	6	12	In stock	0 zł		Enquiry
MU-2899	Ball end - insert for 1/2" nut, 13 mm hose, brass	12	12	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Ball end for hose – insert under the nut – for use in industrial installations, e.g., for air. Material: brass. Working pressure: up to 12 bar. Operating temperature: from -20°C to +100°C.