Can the Clamp with double wire and screw, spring steel be reused after loosening for another hose without losing clamping strength?

Clamp with double wire and screw, spring steel can generally be reused after loosening, but with caveats. Because itâs made of galvanized spring steel, the material has good elasticity and a tendency to retain shape, so the clamp will often provide adequate clamping strength when reused on a hose of similar diameter and condition. Smooth round wire also reduces permanent deformation of the hose. However reuse reliability depends on factors: - Degree of prior tightening and any plastic deformation: if the clamp was overtightened or bent, spring tension may be reduced and clamping force compromised. - Number of reuse cycles: repeated loosening/tightening can fatigue spring steel and reduce bite. - Fit to the new hose and connector shape: a different hose diameter or a stepped/irregular connecting part can reduce sealing even if clamp tension seems adequate. - Application pressure and criticality: for low-pressure ventilation and household appliances reuse is usually acceptable; for higher or safety-critical pressures, replacement is advised. Recommendation: inspect the Clamp with double wire and screw, spring steel for visible deformation, corrosion, or loss of springiness; if it appears intact and used on a similar hose/connector in a low-pressure application it can be reused. For high-pressure, safety-critical, or ill-fitting uses, replace it.

Is the Clamp with double wire and screw, spring steel suitable for use on spiral-external lightweight ventilation hoses?

Yes. The Clamp with double wire and screw, spring steel is suitable for spiral-external lightweight ventilation hoses. Itâs designed specifically for quick fastening of lightweight, low-pressure hoses with an external spiral, with smooth round-wire edges to minimize hose damage. Commonly used in ventilation systems and household appliances; ideal for industrial and domestic use. Note: maximum allowable medium pressure depends on the hose type and the shape of the connecting part.

What is the recommended torque for tightening the Clamp with double wire and screw, spring steel to avoid hose damage?

Clamp with double wire and screw, spring steel: recommended tightening torque is low. typically 1.0â2.5 Nm. Start at ~1.0 Nm and increase gradually, not exceeding 2.5 Nm, to secure the clamp without deforming or cutting the hose. For very thin or fragile hoses, limit torque to ~0.8â1.2 Nm and check for compression marks. Always inspect the hose and connection after tightening and, when in doubt, use a torque-limiting screwdriver or test clamp performance at the lowest effective torque.

Clamp with double wire and screw, spring steel

All products, Clamps for mounting ends/

Additional information

Material	CS – steel (cast iron)

Easy to install and adjust clamp with double wire and screw tightening system designed for quick fastening of lightweight and low-pressure hoses with an external spiral. Smooth edges of the round wire minimize hose damage. The clamp is generally used in ventilation systems or in household appliances. Ideal for industrial and domestic use. Maximum medium pressure depends on the type of hose and the shape of the connecting part. Material: galvanized spring steel (screw made of galvanized steel).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
AB-WCS-10-12-W1	WIRE CLIP-S 9.5÷12, W1	-	-	In stock	Enquiry
AB-WCS-11-13-W1	WIRE CLIP-S 10.5÷13, W1	-	-	In stock	Enquiry
AB-WCS-12-14-W1	WIRE CLIP-S 11.5÷14, W1	-	-	In stock	Enquiry
AB-WCS-13-15-W1	WIRE CLIP-S 12.5÷15, W1	-	-	In stock	Enquiry
AB-WCS-13-16-W1	WIRE CLIP-S 13÷16, W1	-	-	In stock	Enquiry
AB-WCS-14-17-W1	WIRE CLIP-S 13.5÷17, W1	-	-	In stock	Enquiry
AB-WCS-15-18-W1	WIRE CLIP-S 15÷18, W1	-	-	In stock	Enquiry
AB-WCS-16-19-W1	WIRE CLIP-S 15.5÷19, W1	-	-	In stock	Enquiry
AB-WCS-17-20-W1	WIRE CLIP-S 17÷20, W1	-	-	In stock	Enquiry
AB-WCS-18-21-W1	WIRE CLIP-S 17.5÷21, W1	-	-	In stock	Enquiry
AB-WCS-19-22-W1	WIRE CLIP-S 18.5÷22, W1	-	-	In stock	Enquiry
AB-WCS-19-23-W1	WIRE CLIP-S 19÷23, W1	-	-	In stock	Enquiry
AB-WCS-21-24-W1	WIRE CLIP-S 21÷24, W1	-	-	In stock	Enquiry
AB-WCS-22-25-W1	WIRE CLIP-S 21.5÷25, W1	-	-	In stock	Enquiry
AB-WCS-24-27-W1	WIRE CLIP-S clamp 23.5÷27, W1	-	-	In stock	Enquiry
AB-WCS-25-29-W1	WIRE CLIP-S 25÷29, W1	-	-	In stock	Enquiry
AB-WCS-27-31-W1	WIRE CLIP-S 27÷31, W1	-	-	In stock	Enquiry
AB-WCS-29-33-W1	WIRE CLIP-S 29÷33, W1	-	-	In stock	Enquiry
AB-WCS-31-35-W1	WIRE CLIP-S 30.5÷35, W1	-	-	In stock	Enquiry
AB-WCS-33-37-W1	WIRE CLIP-S 33÷37, W1	-	-	In stock	Enquiry
AB-WCS-36-40-W1	WIRE CLIP-S 35.5÷40, W1	-	-	In stock	Enquiry
AB-WCS-39-43-W1	WIRE CLIP-S 38.5÷43, W1	-	-	In stock	Enquiry
AB-WCS-41-46-W1	WIRE CLIP-S 41÷46, W1	-	-	In stock	Enquiry
AB-WCS-44-49-W1	WIRE CLIP-S 43.5÷49, W1	-	-	In stock	Enquiry
AB-WCS-47-53-W1	WIRE CLIP-S 46.5÷53, W1	-	-	In stock	Enquiry
AB-WCS-51-56-W1	WIRE CLIP-S 50.5÷56, W1	-	-	In stock	Enquiry
AB-WCS-54-60-W1	WIRE CLIP-S clamp 53.5÷60, W1	-	-	In stock	Enquiry
AB-WCS-57-64-W1	WIRE CLIP-S 56.5÷64, W1	-	-	In stock	Enquiry
AB-WCS-60-68-W1	WIRE CLIP-S 60÷68, W1	-	-	In stock	Enquiry
AB-WCS-64-72-W1	WIRE CLIP-S 64÷72, W1	-	-	In stock	Enquiry
AB-WCS-69-76-W1	WIRE CLIP-S 68.5÷76, W1	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Easy to install and adjust clamp with double wire and screw tightening system designed for quick fastening of lightweight and low-pressure hoses with an external spiral. Smooth edges of the round wire minimize hose damage. The clamp is generally used in ventilation systems or in household appliances. Ideal for industrial and domestic use. Maximum medium pressure depends on the type of hose and the shape of the connecting part. Material: galvanized spring steel (screw made of galvanized steel).