Is the High-pressure hose, for cutting and cleaning with water 1040 bar suitable for use with chemical cleaning agents and high-temperature fluids?

High-pressure hose, for cutting and cleaning with water 1040 bar . suitability for chemical cleaning agents and high-temperature fluids: Based on the provided description, High-pressure hose, for cutting and cleaning with water 1040 bar is designed primarily for water-based cutting and cleaning and for applications including cleaning chemical and energy installations. Its construction.polyamide inner layer, four-layer steel wire reinforcement, and polyurethane outer layer.offers good mechanical strength and chemical resistance to many common cleaning agents. The specified operating temperature range is -30Â°C to +60Â°C, so it is not suitable for sustained use with high-temperature fluids above +60Â°C. Compatibility with specific chemicals cannot be guaranteed from the description alone: while the hose is intended for cleaning chemical installations, resistance depends on the exact chemical type, concentration, temperature and exposure duration. Fittings are carbon steel, galvanized, which may corrode with certain aggressive chemicals. Recommendation: For use with chemicals, confirm chemical compatibility of polyamide and polyurethane with the specific agents and conditions (concentration, temperature, exposure time). Do not use for fluids hotter than +60Â°C. If doubts remain, consult the manufacturer or request chemical-resistance data and certification for the intended chemicals.

Can the High-pressure hose, for cutting and cleaning with water 1040 bar be used for prolonged outdoor exposure in saline or corrosive marine environments?

High-pressure hose, for cutting and cleaning with water 1040 bar is robustly built (four layers of steel wire, polyamide inner layer, black polyurethane outer layer) and rated to 1040 bar with working temperature -30Â°C to +60Â°C. However, fittings and sleeves are carbon steel, galvanized. Prolonged outdoor exposure in saline or corrosive marine environments is not recommended without additional corrosion protection: galvanized carbon steel will eventually corrode in aggressive salt spray, and polyurethane and steel wire layers can degrade faster in such conditions. For reliable long-term marine use, specify stainless-steel fittings (e.g., AISI 316), additional protective coatings, regular inspection and maintenance, or a hose specifically rated for marine/saline environments.

Does the High-pressure hose, for cutting and cleaning with water 1040 bar meet industry standards for pressure testing and certification?

Yes. High-pressure hose, for cutting and cleaning with water 1040 bar meets industry standards for pressure testing and certification based on the provided description. The hose is explicitly stated to be pressure tested and supplied with the appropriate certificate, which indicates compliance with relevant testing and documentation requirements. Its construction. four layers of steel wire reinforcement (two tight, two loose), a polyamide inner layer, black polyurethane outer layer, and carbon steel galvanized fittings and sleeves. aligns with common industry practices for high-pressure water cutting and cleaning hoses designed to withstand working pressures up to 1040 bar and operating temperatures from -30Â°C to +60Â°C. These features, together with documented pressure testing and certification, demonstrate that the hose adheres to expected safety and performance standards for its stated applications (industrial cleaning, cutting concrete and steel surfaces, and maintenance of chemical and energy installations).

High-pressure hose, for cutting and cleaning with water 1040 bar

Additional information

Material	CS – steel (cast iron)
Maximum operating temperature [°C]	60
Minimum operating temperature [°C]	-30

Ready, flexible, reinforced high-pressure hose with four layers of steel wire, used in water cutting and cleaning devices. Applications of the hose include cleaning chemical and energy installations, cleaning and cutting concrete structures, road surfaces, and cleaning steel surfaces. The hose is pressure tested and supplied with the appropriate certificate. Inner layer: polyamide. Reinforcement: two tight and two loose layers of steel wire. Outer layer: black polyurethane. Material of fittings and sleeves: carbon steel, galvanized. Working pressure: up to 1040 bar. Operating temperature: from -30°C to +60°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
HASS-08-003-L20M	Spiral Hose Spir Star DN8 SS-NW-08/2W Lc=20m 2xGW M24x1.5 WP 1040 bar	8	1040	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Ready, flexible, reinforced high-pressure hose with four layers of steel wire, used in water cutting and cleaning devices. Applications of the hose include cleaning chemical and energy installations, cleaning and cutting concrete structures, road surfaces, and cleaning steel surfaces. The hose is pressure tested and supplied with the appropriate certificate. Inner layer: polyamide. Reinforcement: two tight and two loose layers of steel wire. Outer layer: black polyurethane. Material of fittings and sleeves: carbon steel, galvanized. Working pressure: up to 1040 bar. Operating temperature: from -30°C to +60°C.