Can Hose for food substances requiring the highest purity PHARMAFLON be sterilized (steam, autoclave, or chemical) without degrading the MFA inner layer or compromising compliance with FDA and USP Class VI?

Hose for food substances requiring the highest purity PHARMAFLON Format can be sterilized, but with conditions to preserve the MFA inner layer and regulatory compliance. Steam/autoclave: MFA (fluoropolymer) is broadly resistant to high temperatures (operating up to +170Â°C) and compatible with steam sterilization in many applications; however, repeated autoclaving at excessive temperature/pressure or improper fitting/clamping that abrades or deforms the inner layer can damage the MFA and compromise USP Class VI suitability. Use validated autoclave cycles within the hose temperature rating, avoid sharp-edged fittings, and ensure electrical continuity and mechanical integrity after sterilization. Chemical sterilization: compatible chemical agents (e.g., hydrogen peroxide vapor, peracetic acid, ethylene oxide) are generally acceptable for fluoropolymers, but each sterilant must be validated for compatibility with MFA, EPDM outer layer, bonding points, and certification retention (FDA/EC/USP). Follow manufacturer validation: use smooth spigot fittings matched to hose ID, clamp sleeves or shell clamps as specified, and avoid oversized or ribbed fittings that could cut the inner layer. In summary: sterilization is possible (steam/autoclave and appropriate chemical methods) if done within the hoseâs thermal/mechanical limits, with correct installation and validated cycles to ensure the MFA inner layer and compliance with FDA and USP Class VI remain intact.

Can Hose for food substances requiring the highest purity PHARMAFLON be used with CIP/SIP procedures without damaging the MFA inner layer or losing regulatory compliance?

Hose for food substances requiring the highest purity PHARMAFLON Format can be used with CIP/SIP procedures without damaging the MFA (PTFE-like) inner layer or losing regulatory compliance, provided correct conditions are met. Its inner smooth fluoropolymer MFA is chemically and thermally resistant (operating â50Â°C to +170Â°C) and complies with FDA 21 CFR 177.1550, EU 10/2011 and USP Class VI, supporting pharmaceutical and food GMP. To avoid damage and maintain compliance, use smooth spigot fittings precisely matched to the hose ID, avoid sharp ribs, and install with clamp sleeves/shell clamps as specified. Ensure CIP/SIP temperatures and chemicals remain within the hoseâs rated limits and follow manufacturer cleaning cycle recommendations. Regular inspection of fittings, continuity (copper wires), and seals is required to preserve integrity and traceability.

Is Hose for food substances requiring the highest purity PHARMAFLON compatible with common pharmaceutical sterilants (e.g., hydrogen peroxide, peracetic acid)?

Hose for food substances requiring the highest purity PHARMAFLON Format is generally compatible with common pharmaceutical sterilants such as hydrogen peroxide and peracetic acid, with important caveats. Why compatible: - Inner layer is smooth MFA (fluoropolymer), which offers excellent chemical resistance to strong oxidizers including hydrogen peroxide and peracetic acid in typical concentrations used for pharmaceutical sterilization. - Construction and materials meet stringent food and pharmaceutical standards (10/2011/EC, FDA 21 CFR 177.1550, USP Class VI), indicating suitability for high-purity and aseptic applications. - Wide temperature range (-50Â°C to +170Â°C) covers thermal conditions used during many sterilization cycles. Caveats and recommendations: - Verify sterilant concentration, temperature and exposure time against MFA chemical resistance data and your process conditions before use. Very high concentrations, prolonged exposure, elevated temperatures or catalysts can accelerate degradation of polymers. - Check compatibilty of other components (sealants, fittings, clamp sleeves, copper wires) with chosen sterilant. - Follow installation guidance (smooth fittings, correct spigot diameter, clamp sleeves) to avoid mechanical damage that could compromise sterilant resistance. - Perform validation and periodic inspection (visual, integrity and extractables testing) after sterilization cycles to confirm no damage, leaching or performance loss. Conclusion: PHARMAFLON Formatâs MFA inner layer is appropriate for common pharmaceutical sterilants in normal use, but confirm specific sterilization parameters and validate in your process prior to routine use.

Hose for substances food demanding maintaining the highest cleanliness PHARMAFLON

All products, Food and beverage hoses/

Additional information

Material	PFA/MFA/FEP – fluoropolymer
Maximum operating temperature [°C]	170
Minimum operating temperature [°C]	-50
Vacuum resistance	yes
Standard length [m]	20, 30, 5, 60
Reinforcement	steel spiral, synthetic cover

Hose suction-delivery intended for conveying products pharmaceutical, cosmetic, substances food, chemical (selection in accordance with rules acc. to chapter “hoses chemical”). Contains no plasticisers, phthalates or substances of animal origin. is characterized high strength thermal and mechanical. is excellent solution for industries processing demanding highest safety during transfer products o high cleanliness. Layer outer resistant to abrasion, ozone and conditions atmospheric. has two copper cable ensuring continuity electrical between fitting hose. standards and requirements : 1) general EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) industry food, contact with food 1935/2004/EC and 2023/2006/EU (GMP). Layer inner compliant with 10/2011/EC, D.M. 21/03/73, FDA 21 CFR 177.1550. Layer outer compliant with FDA 21 CFR 177.2600, D.M. 21/03/73. 3) Pharmaceutical industry: USP CLASS VI (Layer inner). assembly : smooth ends with a spigot (“tail” into the hose) must be used, without sharp or high barbs that could cut or damage the MFA inner layer after clamping. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Assembly with clamping ferrules or shell clamps. Inner layer: smooth polymer fluorine MFA. Reinforcement: cord synthetic, steel spiral. Outer layer: smooth EPDM rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -50°C up to +170°C (for greater chemicals).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MT-PHARMA-100	Hose PHARMAFLON 100x116 mm	100	10	In stock	Enquiry
MT-PHARMA-13	Hose PHARMAFLON 13x25 mm	12	10	In stock	Enquiry
MT-PHARMA-19	Hose PHARMAFLON 19x31 mm	20	10	In stock	Enquiry
MT-PHARMA-25	Hose PHARMAFLON 25x37 mm	25	10	In stock	Enquiry
MT-PHARMA-32	Hose PHARMAFLON 32x45 mm	32	10	In stock	Enquiry
MT-PHARMA-38	Hose PHARMAFLON 38x51 mm	38	10	In stock	Enquiry
MT-PHARMA-51	Hose PHARMAFLON 51x65.5 mm	50	10	In stock	Enquiry
MT-PHARMA-63	Hose PHARMAFLON 63.5x79.5 mm	65	10	In stock	Enquiry
MT-PHARMA-76	Hose PHARMAFLON 76x92 mm	75	10	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Hose suction-delivery intended for conveying products pharmaceutical, cosmetic, substances food, chemical (selection in accordance with rules acc. to chapter “hoses chemical”). Contains no plasticisers, phthalates or substances of animal origin. is characterized high strength thermal and mechanical. is excellent solution for industries processing demanding highest safety during transfer products o high cleanliness. Layer outer resistant to abrasion, ozone and conditions atmospheric. has two copper cable ensuring continuity electrical between fitting hose. standards and requirements : 1) general EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) industry food, contact with food 1935/2004/EC and 2023/2006/EU (GMP). Layer inner compliant with 10/2011/EC, D.M. 21/03/73, FDA 21 CFR 177.1550. Layer outer compliant with FDA 21 CFR 177.2600, D.M. 21/03/73. 3) Pharmaceutical industry: USP CLASS VI (Layer inner). assembly : smooth ends with a spigot (“tail” into the hose) must be used, without sharp or high barbs that could cut or damage the MFA inner layer after clamping. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Assembly with clamping ferrules or shell clamps. Inner layer: smooth polymer fluorine MFA. Reinforcement: cord synthetic, steel spiral. Outer layer: smooth EPDM rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -50°C up to +170°C (for greater chemicals).

Additional information

Material	PFA/MFA/FEP – fluoropolymer
Maximum operating temperature [°C]	170
Minimum operating temperature [°C]	-50
Vacuum resistance	yes
Standard length [m]	20, 30, 5, 60
Reinforcement	steel spiral, synthetic cover