How do I install the Straight drain valve with GZ BSP, EWO to effectively remove condensate and equalize pressure without leaking?

To install the Straight drain valve with GZ BSP, EWO correctly and avoid leaks while effectively removing condensate and equalizing pressure, follow these steps: 1. Preparation - Depressurize and drain the system before work. - Clean the BSP male thread and the mating port; remove debris, old sealant and oil. 2. Thread sealing - Use a suitable thread sealant for metal-metal connections and NBR sealing (e.g., PTFE tape or anaerobic pipe sealant rated for compressed air and up to 25 bar). Wrap PTFE tape clockwise 2â3 turns on the GZ BSP male thread, avoiding tape on the first thread to prevent contamination of the valve seat. 3. Installation orientation - Straight drain valve with GZ BSP, EWO can be mounted in any position . choose the most accessible location for operation and maintenance, near the low point of the line or receiver where condensate collects. 4. Fitting - Hand-start the valve into the female BSP port to avoid cross-threading. Tighten with a wrench to a firm stop; do not over-torque to prevent distorting the nickel-plated brass body or damaging the NBR seal. Follow typical torque guidance for the BSP thread size if available. 5. Function check and bleed - Re-pressurize the system slowly and inspect the connection for leaks using soapy water or leak detector. Operate the valve to ensure it releases air/condensate and that the metal-metal disc seats without seepage. - If minor leaks occur at the thread, depressurize and retighten or reapply sealant. 6. Maintenance tips - Periodically operate the valve to prevent sticking and check the NBR seal condition. Replace the valve if the seal hardens or the metal seating shows wear. By following these steps you ensure Straight drain valve with GZ BSP, EWO vents air, removes condensate and equalizes pressure reliably up to 25 bar and 0â+90Â°C without leaking.

Can the Straight drain valve with GZ BSP, EWO be used at any mounting position without affecting condensate drainage or sealing performance?

Yes. Straight drain valve with GZ BSP, EWO can be used in any mounting position without affecting condensate drainage or sealing performance. It is designed for mounting in any orientation, with a nickel-plated brass body, brass disc, NBR sealing, operating temperature 0Â°C to +90Â°C and working pressure up to 25 bar, suitable for releasing air and removing condensate.

What maintenance is required for the Straight drain valve with GZ BSP, EWO to ensure reliable sealing and long service life?

To ensure reliable sealing and long service life of the Straight drain valve with GZ BSP, EWO, follow these maintenance guidelines: - Regular inspection: Visually check the valve for external damage, corrosion on the nickel-plated brass body, and wear on the brass disc at least monthly in typical industrial use; increase frequency in harsh environments. - Leak checks: Periodically verify sealing integrity (e.g., during pressure tests or system start-ups). Replace the valve or service the seal if any air or condensate leakage is detected. - Seal replacement: The valve uses an NBR (nitrile) seal. Inspect the NBR seat for hardening, cracking or swelling caused by oils, heat or contaminants. Replace the NBR seal when signs of deterioration appear or proactively every 1â3 years depending on duty cycle and operating conditions. - Clean internals: Remove particulate, sludge or condensate deposits that can prevent tight metalâmetal and NBR sealing. Flush or disassemble and clean the disc and seat if buildup is found; ensure all parts are dry and free of debris before reassembly. - Preventive flushing/draining: Regularly drain condensate from the system to reduce exposure of the valve to aggressive mixtures of water and oil that accelerate wear. - Proper operation: Avoid cycling the valve excessively; operate within rated limits (0Â°C to +90Â°C, max 25 bar). Do not expose the NBR seal to temperatures or chemicals beyond specifications. - Thread and mounting care: Check BSP external thread for damage and ensure correct installation torque to avoid thread distortion. Use compatible sealing methods that do not intrude into the valve bore. - Lubrication: No additional lubrication of metalâmetal sealing is normally required; if reassembly requires lubrication, use materials compatible with NBR and compressed air systems. - Spare parts and documentation: Keep replacement NBR seals and, if available, manufacturerâs kit on hand. Record maintenance actions and observations to plan replacements before failures occur. Following these steps will preserve the metalâmetal sealing function, protect the NBR seat, and ensure long reliable service of the Straight drain valve with GZ BSP, EWO.

Straight drain valve with GZ BSP, EWO

All products, Other valves/

Additional information

Material	B – brass (bronze)

Straight drain valve with metal-metal sealing and BSP external thread is used to release air, for example, to equalize pressure in the system. It can also be used to remove condensate from it. Compressed air may contain water vapor, which upon condensation turns into a mixture of water and oil called condensate. If not removed, it can cause failures in both system components and compressed air receivers. Mounting position – any. Body material: nickel-plated brass. Disc material: brass. Sealing: NBR. Operating temperature: from 0°C to +90°C. Working pressure: 25 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Price	Quantity	Actions	Catalogue
EW-16811	Straight drain valve DN 5 with GZ 1/4" BSP	5	25	In stock	0 zł		Enquiry
EW-21201	Straight drain valve DN 5 with GZ 1/8" BSP	5	25	In stock	0 zł		Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Straight drain valve with metal-metal sealing and BSP external thread is used to release air, for example, to equalize pressure in the system. It can also be used to remove condensate from it. Compressed air may contain water vapor, which upon condensation turns into a mixture of water and oil called condensate. If not removed, it can cause failures in both system components and compressed air receivers. Mounting position – any. Body material: nickel-plated brass. Disc material: brass. Sealing: NBR. Operating temperature: from 0°C to +90°C. Working pressure: 25 bar.