How do I choose the right ULTRACLEAN metric pipe cleaning nozzle size for pipes with outer diameters from 3 mm to 50 mm?

Choose the correct ULTRACLEAN metric pipe cleaning nozzle Format by matching the nozzleâs internal limiter and front-seal design to your pipeâs external diameter and wall thickness. Because sealing occurs between the pipeâs front edge and the internal limiter, you must ensure the nozzle variant corresponds to the pipe OD so the front face meets the limiter squarely and the wall thickness sits within the nozzleâs accepted range. Steps: 1. Measure the pipe outer diameter (OD) precisely (3 mmâ50 mm range). 2. Check the ULTRACLEAN metric pipe cleaning nozzle Format chart/specs for the nozzle model that covers your measured OD. Each Format nozzle is sized to form a seal at a specific OD interval. 3. Verify wall thickness compatibility . the nozzle accepts a range of wall thicknesses for each OD size; confirm your pipeâs wall thickness falls inside that range so the front face contacts the limiter properly. 4. If your OD sits at a boundary between sizes, choose the nozzle specified for that exact OD rather than a neighboring size to ensure reliable sealing. 5. For unusual profiles, deformations, or tubing with flared ends, pre-process the end to a clean, square cut so the front surface can seat against the limiter. Result: a correctly matched ULTRACLEAN metric pipe cleaning nozzle Format will seal at the pipe front against the limiter, enabling effective cleaning for pipes from 3 mm to 50 mm OD.

Can the ULTRACLEAN metric pipe cleaning nozzle seal pipes with varying wall thicknesses within the 3â50 mm OD range?

Yes. The ULTRACLEAN metric pipe cleaning nozzle seals pipes by pressing the pipeâs front face against an internal limiter inside the nozzle. It is specifically designed for metric pipe external diameters and wall thicknesses within the stated range and accommodates pipes with wall thicknesses that fall inside the 3â50 mm OD size range.

Does the ULTRACLEAN metric pipe cleaning nozzle require special maintenance for different pipe OD sizes?

No, the ULTRACLEAN metric pipe cleaning nozzle Format does not require special maintenance tied to different pipe outer diameters (ODs). The nozzle is designed to seal against the pipe between the pipeâs front surface and the internal limiter, accommodating metric pipe ODs and wall thicknesses from 3 mm to 50 mm. Because sealing and alignment are handled by this builtâin limiter, routine maintenance is the same regardless of the specific pipe OD used within that range. Recommended routine maintenance (applies to all supported pipe sizes): - Inspect the limiter and front sealing surface for wear, nicks or deformation before and after use. - Clean debris and deposits from the sealing surface and internal cavity to ensure reliable sealing. - Replace worn or damaged limiters/seals to maintain proper fit and prevent leaks. - Verify that the nozzle mates properly with the pipe end; adjust mounting or alignment if needed. - Follow general ULTRACLEAN device maintenance and cleaning schedules for safe, efficient operation. If you plan to use pipes at the extremes of the 3â50 mm range frequently, increase inspection frequency for wear but no special, sizeâspecific maintenance procedures are required.

ULTRACLEAN metric pipe cleaning nozzle

All products, Other devices/

Additional information

Standard length [m]	15

Cleaning nozzle for metric pipes, for use with ULTRACLEAN devices. The sealing of the pipe with the nozzle occurs between the front surface of the pipe and the limiter located inside the nozzle. Designed for external diameters and wall thicknesses of metric pipes. Pipe size range: from 3 mm to 50 mm.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
UC-NP06X1,5	Nozzle for pipe 6x1.5 mm	-	-	In stock	Enquiry
UC-NP08X1,5	Nozzle for pipe 8x1.5 mm	-	-	In stock	Enquiry
UC-NP10X1,5	Nozzle for pipe 10x1.5 mm	-	-	In stock	Enquiry
UC-NP12X2,0	Nozzle for pipe 12x2.0 mm	-	-	In stock	Enquiry
UC-NP14X2,0	Nozzle for pipe 14x2.0 mm	-	-	In stock	Enquiry
UC-NP15X2,0	Nozzle for pipe 15x2.0 mm	-	-	In stock	Enquiry
UC-NP16X2,5	Nozzle for pipe 16x2.5 mm	-	-	In stock	Enquiry
UC-NP18X2,5	Nozzle for pipe 18x2.5 mm	-	-	In stock	Enquiry
UC-NP20X3,0	Nozzle for pipe 20x3.0 mm	-	-	In stock	Enquiry
UC-NP22X2,0	Nozzle for pipe 22x2.0 mm	-	-	In stock	Enquiry
UC-NP25X3,0	Nozzle for pipe 25x3.0 mm	-	-	In stock	Enquiry
UC-NP28X2,5	Nozzle for pipe 28x2.5 mm	-	-	In stock	Enquiry
UC-NP30X4,0	Nozzle for pipe 30x4.0 mm	-	-	In stock	Enquiry
UC-NP35X3,0	Nozzle for pipe 35x3.0 mm	-	-	In stock	Enquiry
UC-NP38X5,0	Nozzle for pipe 38x5.0 mm	-	-	In stock	Enquiry
UC-NP42X3,0	Nozzle for pipe 42x3.0 mm	-	-	In stock	Enquiry
UC-NP50X6,0	Nozzle for pipe 50x6.0 mm	-	-	In stock	Enquiry
UC-NT03	NT03 nozzle	-	-	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Cleaning nozzle for metric pipes, for use with ULTRACLEAN devices. The sealing of the pipe with the nozzle occurs between the front surface of the pipe and the limiter located inside the nozzle. Designed for external diameters and wall thicknesses of metric pipes. Pipe size range: from 3 mm to 50 mm.