Can the 90Â° hose end with BSP GZ, PVDF plastic, 1W+ series type EM be autoclaved or sterilized for use in medical and pharmaceutical applications?

90Â° hose end with BSP GZ, PVDF plastic, 1W+ series type EM: PVDF (polyvinylidene fluoride) as a material is chemically resistant and has good thermal stability; it can generally withstand autoclave temperatures (typically 121â134 Â°C). However, suitability for repeated steam sterilization and for regulated medical/pharmaceutical use depends on more than base material: design, seals, hose compatibility, and construction tolerances matter. From the provided description: - Material: PVDF . compatible with typical autoclave temperatures. - Working pressure: 4 bar . autoclave steam pressure (~2â3 bar at 121â134 Â°C) is below this rating. - Intended hoses: flexible corrugated hoses with smooth inner surface and unreinforced PTFE hoses . these hoses may or may not be autoclave-compatible; PTFE generally is, but corrugated polymers vary. - Series 1W+ does not require smoothing of grooves . groove geometry can affect cleanability and validation for sterile applications. Conclusion / recommendations: 1. Thermally, 90Â° hose end with BSP GZ, PVDF plastic, 1W+ series type EM can tolerate autoclave temperatures in principle, and its pressure rating exceeds typical autoclave pressure. 2. For validated medical/pharmaceutical use you must confirm: manufacturerâs autoclave/sterilization certification, compatibility of the specific hose to be used, integrity of any seals or gaskets under steam, and suitability of the groove/design for cleaning/sterility validation. 3. If manufacturer documentation is unavailable, perform compatibility testing (repeated autoclave cycles, pressure/leak tests, visual inspection, and microbial/pyrogen testing) and consult regulatory/quality assurance requirements before use.

Is the 90Â° hose end with BSP GZ, PVDF plastic, 1W+ series type EM compatible with common chemical cleaning agents used in labs?

90Â° hose end with BSP GZ, PVDF plastic, 1W+ series type EM is generally compatible with a wide range of common chemical cleaning agents used in laboratories. PVDF (polyvinylidene fluoride) offers excellent chemical resistance to acids, bases, solvents and many aggressive reagents, making it suitable for lab, pharmaceutical and chemical environments. Limitations: avoid strong reductants (e.g., molten alkali metals), certain highly oxidizing conditions at elevated temperature, and solvents/conditions known to swell or stress-crack fluoropolymers. Also respect the working pressure (4 bar) and use only intended hose types (flexible corrugated with smooth inner surface and unreinforced PTFE). For critical or unusual chemicals, verify compatibility with supplier chemical-resistance data or perform testing.

Does the 90Â° hose end with BSP GZ, PVDF plastic, 1W+ series type EM require specific cleaning procedures after contact with food products?

90Â° hose end with BSP GZ, PVDF plastic, 1W+ series type EM: After contact with food products, specific cleaning procedures are recommended. Although the 1W+ series does not require smoothing of the grooves on the hose ends and is made of chemically resistant PVDF suitable for food-related environments, proper hygienic cleaning depends on the type of food product, level of soiling, and regulatory hygiene standards. Recommended practices: - Flush immediately after use with potable water to remove residues. - Use food-safe detergents or enzymatic cleaners appropriate for the residues (fats, proteins, sugars), following manufacturer instructions and concentration limits safe for PVDF. - For microbial control, use compatible sanitizers (e.g., peracetic acid, diluted bleach solutions) at concentrations and contact times approved for PVDF and food-contact equipment; rinse thoroughly after sanitization. - Avoid harsh solvents, strong alkalis at high concentrations, or aggressive mechanical scrubbing that could damage mating parts or seals. - Inspect seals, hose connections and inner hose surfaces regularly for residue build-up; disassemble if necessary for manual cleaning according to component compatibility. - Validate cleaning frequency and procedures per food safety regulations (HACCP, local law) and the specific productâs contamination risk. If in doubt, consult the hose and fitting manufacturers for recommended cleaning agents and maximum temperatures/pressures for cleaning cycles to ensure compatibility with PVDF and the 90Â° hose end with BSP GZ, PVDF plastic, 1W+ series type EM.

90° hose end with BSP GZ, PVDF plastic, 1W+ series type EM

All products, Low-pressure fittings and adapters/

Additional information

Material	P – material (plastic)

90° hose fitting with GZ BSP, type EM, finds wide application in laboratories, medicine, pharmaceutical, chemical, and food industries. The design allows for multiple installations without the need for tools. Series 1W+ does not require smoothing of the grooves on the hose ends. It is intended for flexible, corrugated hoses with a smooth inner surface and unreinforced PTFE hoses. Material: PVDF. Working pressure: 4 bar.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
EM-1WP200MG1114PV	90° elbow (series 1W+) with GZ BSP 1/4", corrugated hose 1/4", PVDF	-	4	In stock	Enquiry
EM-1WP200MG1538PV	90° elbow (series 1W+) with GZ BSP 3/8", corrugated hose 3/8", PVDF	-	4	In stock	Enquiry
EM-1WP200MG1812PV	90° elbow (series 1W+) with GZ BSP 1/2", corrugated hose 1/2", PVDF	-	4	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

90° hose fitting with GZ BSP, type EM, finds wide application in laboratories, medicine, pharmaceutical, chemical, and food industries. The design allows for multiple installations without the need for tools. Series 1W+ does not require smoothing of the grooves on the hose ends. It is intended for flexible, corrugated hoses with a smooth inner surface and unreinforced PTFE hoses. Material: PVDF. Working pressure: 4 bar.