Is the TRI-CLAMP coupling clamp stainless steel, series 3C type EM compatible with standard tri-clamp ferrules and what gasket materials are recommended?

Yes. The Obejma zÅÄcza TRI-CLAMP stal nierdzewna, seria 3C typ EM is compatible with standard tri-clamp ferrules: it uses the common tri-clamp clamping geometry and will mate with industry-standard ferrules of matching nominal size. Recommended gasket materials depend on the application: - EPDM: Good for general-purpose use, steam, hot water, and many food & beverage applications (not compatible with oils or hydrocarbons). - PTFE (Teflon): Excellent chemical resistance and wide temperature range; ideal for aggressive chemicals and pharmaceutical use. - Silicone: Good for high-temperature and food contact where flexibility is required; limited chemical resistance. - Viton (FKM): Best for oil, solvent and high-temperature chemical resistance; not recommended for steam. - FDA-compliant materials: Choose EPDM, PTFE or silicone grades that meet FDA 21 CFR for direct food/pharma contact. Select gasket material based on media compatibility, temperature, pressure and regulatory (FDA/USP) requirements. Ensure gasket dimensions match the clamp/ferrule size for a proper seal.

Does the Obejma zÅÄcza TRI-CLAMP stal nierdzewna, seria 3C typ EM require special torque settings during installation?

Obejma zÅÄcza TRI-CLAMP stal nierdzewna, seria 3C typ EM does not typically require special torque settings beyond standard practice. Installation should follow manufacturer recommendations for clamp snugness to ensure proper gasket compression and hygienic seal; overtightening can deform the clamp or gasket, undertightening can leak. If manufacturer documentation for series 3C type EM specifies torque values, use those; otherwise tighten evenly until clamp halves seat and gasket is compressed uniformly, then secure bolts/nuts to a firm, hand- or wrench-tight level. For critical sanitary, pressure, or ASME-validated systems, consult supplier specs or use a calibrated torque wrench per provided torque chart.

Can Obejma zÅÄcza TRI-CLAMP stal nierdzewna, seria 3C typ EM be used in CIP/SIP sterilization cycles?

Yes. The Obejma zÅÄcza TRI-CLAMP stal nierdzewna, seria 3C typ EM can be used in CIP (Cleaning In Place) and SIP (Sterilization In Place) cycles, provided standard conditions and good maintenance practices are observed. Key reasons: - Material compatibility: Made of stainless steel, the clamp resists common CIP/SIP agents (hot water, steam, caustic and acidic detergents) and withstands elevated temperatures used in sterilization. - Design suitability: TRI-CLAMP style clamps provide secure, sanitary connections with smooth surfaces and minimal crevices, reducing fouling and enabling effective cleaning and sterilization. - Durability: Stainless steel clamps of this design tolerate repeated thermal and chemical cycles typical for production environments. Operational caveats: - Verify specific stainless steel grade (e.g., 304 vs 316L): For aggressive chemistries or high-salt environments, 316L is preferred for superior corrosion resistance. - Check gasket material compatibility: The clamp itself is stainless steel, but CIP/SIP success depends on gasket (seal) material; use steam- and chemical-resistant gaskets (e.g., PTFE, EPDM rated for process temperatures). - Inspect clamp condition regularly: Ensure surfaces are free of pitting, cracks, or weld defects that could harbor microbes or corrode under CIP/SIP. - Follow manufacturer limits: Confirm maximum temperature and pressure ratings and any manufacturer maintenance/cleaning recommendations. Conclusion: The Obejma zÅÄcza TRI-CLAMP stal nierdzewna, seria 3C typ EM is suitable for CIP/SIP when used with appropriate gasket materials, proper stainless steel grade, and adherence to manufacturer limits and maintenance.

Clamp for the connection TRI-CLAMP stainless steel, 3C series type EM

All products, Low-pressure fittings and adapters/

Additional information

Material	SS – stainless steel

Clamp for the connection TRI-CLAMP 3C series type EM. Material: stainless steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
EM-3C001SE1	Clamp TRI-CLAMP (3C series) for a flange 25 mm, stainless steel	-	-	In stock	Enquiry
EM-3C001SE2	Clamp TRI-CLAMP (3C series) for a flange 34 mm, stainless steel	-	-	In stock	Enquiry
EM-3C001SE3	Clamp TRI-CLAMP (3C series) for a flange 50.5 mm, stainless steel	-	-	In stock	Enquiry