Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrength hose delivery intended for conveying water industrial, sewage, sludge, etc. Inner layer: black smooth rubber SBR. Reinforcement: cord synthetic o high strength. Outer layer: black rubber SBR. Working pressure: 10 bar. Operating temperature: od -30°C up to +70°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery Light, flexible, having resistance to creasing hose intended for discharge air, fumes, dusts fibres, dust and other light substances. used in vacuum cleaners industrial. made with conductive polyethylene (PE) and elastomer, o low resistance material, excellent for applications in which required is avoiding accumulation charges electric (should then effectively earth hose). shaped in profile hose outer spiral reinforcing, left-handed, allows screwing on appropriate ends for vacuum cleaners with a left-hand thread e.g. ends plastic for hose EVA: DN32, 38 and 50 or appropriate ends conductive. Assembly of the hose with clamps on suitable ends, pipe spigots etc. is also possible. hose o diameter DN38 and DN50 has declaration conformity with requirements ATEX and standards TRGS 727 and It can be used in zones hazard explosion, under a condition effective earthing hose and carrying out through user analysis risk. Hose material: black special polyethylene (PE) and elastomer. Reinforcement: spiral reinforcing shaped in material hose. Operating temperature: od -20°C up to +60°C (podworking pressure depends on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose delivery, o thick wall, intended for conveying substances food requiring the use of rubber free of odour and taste. Contains no phthalates or bisphenol A. hose specially designed for conveying oils and fats. Widely used in industry oil and fat. Layer outer in fully resistant to fat and aging. standards and requirements : industry food, contact with food 1935/2004/EC and 2023/2006/EC (GMP). Layer inner compliant with FDA 21 CFR 177.2600, D.M. 21/03/73. Inner layer: white NBR rubber/PVC. Reinforcement: two layer cord synthetic. Outer layer: blue rubber CR. Working pressure: 10 bar. Operating temperature: -15°C up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose non-conductive charges electrical - leakage in conditions testing acc. to standards SAE 100 R8 smaller od 50 µA for voltage 246 kV/m through 5 min., used in the vicinity installation electrical. Inner layer: polyester. Reinforcement: two aramid braids. Outer layer: orange polyurethane. pressure working: 700 bar. temperature use: from -40°C to +100°C (for water and liquids na base water max. up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for oil hydraulic systems, gases, air, fuels, water-based fluids. standards: SAE 100R8, ISO 3949-R8 (except DN8). Inner layer: polyester. Reinforcement: a double aramid braid. Outer layer: micro-perforated polyurethane. Working pressure: from 140 bar to 362 bar, depending on the hose diameter. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / Details
WEICON paste assembly Anti-Seize HIGH-TECH, type pen 30 g
All products | Cleaning agents, maintenance products, assembly compounds, and protective coatings0 złPaste assembly Weicon Anti-Seize High Tech ensures protection against corrosion, seizing and „cold welding”, especially on steel stainless. recommended especially for use in extreme conditions e.g.: at high temp., agents aggressive, high pressures, as well as for lubrication loaded bearings and surfaces sliding (only in engines low-speed). eliminates squeals and squeaking, has good properties sealing, allows easy assembly and disassembly components. economical in use and free od metals toxic, consistency NLGI - Class 1. Operating temperature: od -40°C up to +1400°C. conducts heat. resistant to changes temperatures and loads pressure (230N/mm 2 ). Packaging - pen type 30 g. - Select options This product has multiple variants. The options may be chosen on the product page / DetailsA two-part insert of a DIN 3015 type 101 clamp, made in accordance with the DIN 3015 standard. As standard, it has a profiled (grooved) surface of the pipe hole. Material insert: rubber. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium size plug quick coupling without valve with fitting for hose intended for installations washing, filtration water deionized, machines industrial, detection leakage, itp. Length L - total length. Material: polypropylene. Sealing: O-ring EPDM. Working pressure: for 8.3 bar. Operating temperature: from 0°C to +71°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA high-quality NiTO water quick coupling plug 1" with a thread internal. Material: brass chrome-plated. Working pressure: up to 25 bar. Operating temperature: up to +80°C. Sealing: NBR (not suitable for gasolines and oils).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap SAFLOK® DC is a variant of the CAMLOCK coupling with protection against accidental opening of the coupling. The protection consists of resilient latches placed in the levers of the socket. When the lever is closed, the latches lock automatically. Unlocking during opening requires pulling back the latches. cap SAFLOK® DC is compatible with other CAMLOCK couplings made in accordance with the MIL-C-27487 standard. Spare parts are available: levers with latches and pins. Material: steel AISI 316. Sealing: NBR. Working pressure: 20 bar (3/4" ÷ 2"), 10 bar (2.1/2" ÷ 4"). Operating temperature: from -40°C to +93°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal ball valve type 5311, configuration L, intended for installations industrial. can be used for air, gases, water, chemicals, products petrochemical, itp., taking into account chemical resistance material valve and sealing. Meets the requirements of the PED 2014/68/EU directive. Working pressure dependent is od temperature use. Material the body: brass nickel-plated. Material the ball: brass chrome-plated. Material lever: aluminum. sealing the ball: PTFE. sealing stem: NBR. connection: BSP female. Operating temperature: from -10°C to +110°C
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal valve butterfly, wafer-type, centric, type WAFER, intended for installation industrial. used m.in. for cold or hot water, water potable, water sea and demineralised, alcohols, milk limestone, hydroxide sodium and other media, taking into account resistance chemical material valve and seal. can be closed and opened manually, or using actuator pneumatic. handle sets valve in 10 positions: „open”, „closed” and in positions intermediate. Dla sizes od DN200 occurs lever with regulation stepless. meets requirements the directive PED 2014/68/UE. has certificate PZH and certificate Lloyd’s Register. Material body: cast iron gray EN-GJL-250, coated epoxy 80 µm. Material disc: cast steel stainless CF8M. Material stem: steel stainless AISI 416. Material lever: aluminum. sealing disc and stem: EPDM. Connection: flange PN6 for DN40 ÷ DN150 and DN300, PN10/PN16 for DN32 ÷ DN300, ASA150 for DN40 ÷ DN300, JIS 10K for DN40 ÷ DN300. Operating temperature: od -15°C up to +110°C (momentarily up to +130°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal directional valve with control by manual, a lever 90°, most often used for controlling the operation of actuators. It can be mounted in-line, on a wall, directly on actuators or on a connection block. Function 3/2 - three-way, two-position. Size: 1/8", 1/4" or 1/2". Material: body valve - aluminum, spool - aluminum nickel-plated, sealing - NBR, Cover end - plastic plastic. pressure working: up to 10 bar. Operating temperature: -10°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal valve check type 2281 intended for installation industrial, It can be used for air, gases, water, chemicals, products petrochemical, etc., taking into account resistance chemical material valve. valve can be mounted in any position, in accordance with direction flow the medium indicated on body. maximum pressure working fixed in full the scope temperatures use. Body material: brass. Material spring: steel AISI 302. butterfly valve: brass. sealing butterfly valve: FKM. Connection: BSP female. Operating temperature: od -10°C up to +90°C. minimal pressure opening: 0.02 bar for 3/8" ÷ 2.1/2"; 0.1 bar for 3" ÷ 4".
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle for cleaning pipes. Material: steel stainless. Working pressure: up to 250 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA spray nozzle 1/4" o simple concentrated jet FULL JET with a BSPT male thread for mounting np. with lance (connection using sockets). Material: steel stainless.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal Filter intended for installation water-supply, sanitary, heating, irrigation, industrial etc. Filter must be mounted in accordance with direction flow the medium marked on body. pressure working dependent is od temperatures use. Filtration grade: 500 µm (od 1/2" for 2"), 600 µm (od 2.1/2" for 4"). Body material: brass. sealing: NBR. insert filter: steel stainless AISI 304. Connections: BSP female. Operating temperature: od -10°C up to +90°C. Working pressure: 16 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light and flexible hose delivery flat-folding for water for hydrants and pumps fire-protection, without couplings. hose hydrant compliant with the standard EN 14540 used is in hydrants internal acc. to EN-671-2. hose for pumps used is for motor pumps firefighting, rescue and services forest. besides function fire-protection Widely used in industry, construction, agriculture and mining. can serve for conveying water, water sea, water industrial, solutions some substances chemical. Layer inner smooth, resistant to mould and rotting. Layer outer (braid) o high strength, resistant to conditions atmospheric and abrasion. Available also in version yellow luminescent (DN52, DN75, 20m, for pumps). certificates (Poland): hoses compliant with conditions technical regulation MSWiA with 27.04.2010. Inner layer: insert PVC (PU for DN110). Reinforcement: a polyester braid. Working pressure: from 12 bar to 15 bar - depending on the diameter hose. Operating temperature: od -30°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA swivel push-in fitting with an O-ring for a high-pressure gun. It prevents the line from breaking. Material: steel stainless.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMulti-output distribution manifold with 1/4" outlets for use in pneumatic systems, allowing pressurized compressed air to be split into several branches. It has additional holes for fixing it at the desired point of the installation. Working pressure: 12 bar. Operating temperature: from -10°C to +80°C. Material: anodized aluminum.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA rubber bellows for a compensator, intended for work in installations in which the medium consists of mineral oils, vegetable and animal fats, oils in aerosol, water with the addition of anti-corrosion substances. Inner layer: rubber NBR. Reinforcement: nylon cord. Outer layer: rubber CR. Operating temperature: from -30°C to +90°C (depending on medium).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLeft-hand bridge worm-drive clamp with a band width of 9 and 12 mm, intended for quick and easy repeated fastening of hoses reinforced with a steel spiral, e.g., ventilation hoses. The bridge's task is to enclose the spiral wire and ensure the clamp fits the hose accurately. Using a bridge in the clamp provides a tight connection that does not damage the hose. The left-hand OML clamp is intended for mounting CLIP type hoses (hoses of this type are made of impregnated fabric, and the left-wound spiral is made of sheet metal and steel wire), e.g., KEVLAR SI CL, SILICON CL, TEFLON CL, GRIPFLEX. The clamp's unique worm mechanism in a compact housing and the cold-formed thread in the band, smooth on the inside, ensure a secure, repeated grip without damaging the hose surface. The number of segments depends on the clamp's minimum/maximum diameter. Material: AISI 430 steel (screw made of galvanized steel).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAn AKBO HEAVY DUTY water gun BIG FLOW, o increased flow. Made of stainless steel, insulated trigger, EPDM rubber guards, Viton seals. It has an adjustable outlet nozzle, smooth flow regulation and a trigger lock. Connection: 1/2" BSP female. maximum Working pressure: 24 bar. Maximum Operating temperature: +95°C. Flow rate: 48 l/min (5 bar), 120 l/min (24 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting straight JIC 37° with BSP male thread (elastomer gasket with a rectangular cross-section). Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTape for system Band-It® Junior, to system clamping using band in ready sections formed in clamps o double loop with built-in a buckle. A band with a smooth surface and its correct installation on a non-serrated hose creates a tight fixing of the fitting, preventing leaks into the inside of the clamp. installing using tool BD-C00189 with an adapter pre forming clamps BD-J00199. Material: steel AISI 201.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrew-together ferrule for non-skive rubber hydraulic hoses type 1SN(R1AT). Use only with fittings screw-together from the same supplier (TI-S...). Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHandle assembly sensor proximity for actuators ISO 15552, in version with sleeve cylindrical. Material: aluminum. Diameter: 160 ÷ 200.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPractical handle magnetic for guns for air CEJN series 208 and 210, which facilitates daily operation operator. has strong magnet, which enables mounting na metal surfaces. handle is easy in mounting, both po right jak and po left side the gun.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGasket envelope-type for part female (socket) coupling CAMLOCK. Material: PTFE/NBR. Operating temperature: from -40°C to +93°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA seal with a circular cross-section (O-ring) for general use (Range 18x1.5 ÷ 35x4). Material: NBR, hardness 70 acc. to Shore'a.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible hose delivery intended for conveying water potable cold (+23°C) and hot (+60°C). its white, mirror surface inner prevents formation biofilm on walls and is easy in maintaining cleanliness. Not affects negatively on properties health, free of is phthalates, ADI (contaminants origin animal) and other substances hazardous subject restrictions in accordance with REACH. Not causes changes properties organoleptic water even in elevated temperatures. Layer outer resistant to abrasion, ozone and conditions atmospheric. cleaning: steam water o temp. +120°C through maximum 30 min. (in system open), other (CIP) in consultation with Tubes International. standards and requirements : 1) general: EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) approval for water potable: PZH B.BK.60110.0823.2022 (valid for 10.08.2025 r.), UBA-Leitlinie, KTW, DVGW W270, D.M.174. 3) industry food, contact with food: EC 1935/2004, EC 2023/2006 (GMP); EC 10/2011 (Layer inner). Inner layer: smooth o mirror surface technopolymer. Reinforcement: a synthetic braid. Outer layer: blue technopolymer. Working pressure: from 10 bar to 20 bar, depending on the diameter hose. Operating temperature: from -30°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light, very flexible and pliable hose intended for discharge aggressive vapours chemical and gases, ventilation and air conditioning. good resistance chemical on solvents and other aggressive vapours. Checking chemical resistance - the chemical resistance table for polyethylene (preliminary selection), confirmation of resistance and conditions of use - by Tubes International. resistant to hydrolysis and corrosion biological. Contains no halogen compounds or plasticisers. used mainly in industry chemical. on request available diameter in the scope 40 ÷ 610 mm. hose available in two versions: P2PE - standard and P2PE EL - conductive electrically o resistance R ≤10 4 Ω, compliant with the directive ATEX 2014/34/EU and the standard TRGS 727, made with black polyethylene. Hose material: polyethylene (PE), transparent - version standard P2PE, black - version conductive electrically P2PEEL. Wall thickness: 0.4 mm. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for solvents, paints, isocyanate, polyol, gases, air, water-based fluids. standards: DIN 24951, SAE 100R7, ISO 3949-R7. Inner layer: polyamide. Reinforcement: a double polyester braid. Outer layer: micro-perforated polyurethane. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA two-part insert of a DIN 3015 type 101 clamp, made in accordance with the DIN 3015 standard. As standard, it has a profiled (grooved) surface of the pipe hole. Material insert: aluminum. Operating temperature: up to +350°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug water quick coupling NiTO CLICK 1/2" with a thread external. NiTO CLICK quick couplings are water quick couplings made to the profile of very popular plastic garden quick couplings and compatible with them. Sealing by means of an O-ring placed externally on the plug. Manufactured in Denmark – 5-year warranty. They retain the simplicity of the commonly known plastic quick couplings and are characterized by strength and durability. Intended for water, water with cleaning agents, for use in industry, services, horticulture, agriculture, etc.. Material: brass chrome-plated (matte - satin). Working pressure: up to 25 bar. Operating temperature: from -30°C to +80°C. Sealing: NBR (not suitable for gasolines and oils).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve throttle check type MRF OMC series COMPACT "O" for direct mounting in connections the actuator, used in systems pneumatic for adjustment rate flowing stream compressed air and direction flow. Equipped with a push-in connector ensuring easy disassembly of pneumatic lines. Setting adjustment using a screwdriver, with the possibility of mounting a protective cover. Size: M5, 1/8″, 1/4″, 3/8″, 1/2″. pressure working: up to 10 bar. Operating temperature: from -10°C to +70°C. Material: brass nickel-plated.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal ball valve type 4170 intended for installations industrial. can be used for air, gases, water, chemicals, products petrochemical, itp., taking into account chemical resistance material valve and sealing. Meets the requirements of the PED 2014/68/EU directive. Working pressure dependent is od temperature use. Material the body: brass nickel-plated. Material the ball: brass chrome-plated. Material lever: aluminum. sealing the ball: PTFE. sealing stem: NBR. connection: BSP female. Operating temperature: from -20°C to +110°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal valve butterfly, wafer-type, centric, type WAFER, intended for installation industrial. used m.in. for cold or hot water, water potable and other media, taking into account resistance chemical material valve and seal. can be closed and opened manually, or using actuator pneumatic. handle sets valve in 10 positions: „open”, „closed” and in positions intermediate. Dla sizes od DN200 occurs lever with regulation stepless. meets requirements the directive PED 2014/68/UE. has certificate PZH and certificate Lloyd’s Register. Material body: cast iron gray EN-GJL-250. Material disc: cast iron spheroidal nickel-plated EN-GJS-400-15. Material stem: steel stainless AISI 416. Material lever: aluminum. sealing disc and stem: EPDM. Connection: flange PN6 for DN40 ÷ DN150 and DN300, PN10/PN16 for DN32 ÷ DN300, ASA150 for DN40 ÷ DN300, JIS 10K for DN40 ÷ DN300. Operating temperature: od -15°C up to +110°C (momentarily up to +130°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSwivel coupling straight GGIL with bearing ball intended for oil hydraulic. used in systems demanding connections swivel in order to eliminating stresses hoses. coupling intended for performing revolutions at small moment swivel. Not is designed for use with large speeds swivel. Material: steel galvanized. sealing: NBR. Connection: male / BSP female. Operating temperature: od -40°C up to +106°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling push-in straight with a thread external tapered, type R1C, Intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
