Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic high-pressure adapter, type A101, with BSP male thread (60° cone sealing). Material: carbon steel, galvanized.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA spray nozzle 1/4" o flat angled jet with a BSPT male thread for mounting np. with lance (connection using sockets). Material: steel stainless.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA set of replaceable seals for a compact actuator ISO 21287, LINER series. Material: polyurethane. Diameter: 32 ÷ 63.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLance extension ventilated with insulation thermal, intended for a high-pressure washer. length: 400 mm. Connections: (inlet) 1/4" BSP male / (outlet) 1/4" BSP male. Working pressure: up to 310 bar. pressure The permissible: 350 bar. Flow rate: 45 l/min. Operating temperature: up to +160°C. Material: steel stainless.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLeft-hand bridge worm-drive clamp with a band width of 9 and 12 mm, intended for quick and easy repeated fastening of hoses reinforced with a steel spiral, e.g., ventilation hoses. The bridge's task is to enclose the spiral wire and ensure the clamp fits the hose accurately. Using a bridge in the clamp provides a tight connection that does not damage the hose. The left-hand OML clamp is intended for mounting CLIP type hoses (hoses of this type are made of impregnated fabric, and the left-wound spiral is made of sheet metal and steel wire), e.g., KEVLAR SI CL, SILICON CL, TEFLON CL, GRIPFLEX. The clamp's unique worm mechanism in a compact housing and the cold-formed thread in the band, smooth on the inside, ensure a secure, repeated grip without damaging the hose surface. The number of segments depends on the clamp's minimum/maximum diameter. Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAn AKBO hot-water gun BIG FLOW, o increased flow. Made of stainless steel, insulated trigger, EPDM rubber guards, Viton seals. Use for hot water requires particular caution. It is not intended for steam! Connection: 1/2" BSP female. Working pressure: 24 bar. Flow rate: 120 l/min. Operating temperature: up to +95°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA multiple bottom plate for welding, for mounting DIN 3015 standard clamps type 100/101. For dimension groups 0 ÷ 3, number of clamps: 10. For dimension groups 4 ÷ 5, number of clamps: 5. For dimension group 0 there is one bolt hole. For dimension groups 1 ÷ 6 there are two bolt holes. Material: steel carbon or steel AISI 316L.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCounter-flange SAE 6000 with a weld-on socket for connection to a flange connection, without mounting screws or a seal. Material: carbon steel, galvanized. Operating temperature: from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA steel wire spiral protecting the fitting against mechanical damage from the outside, which extends the service life of the line.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSleeve dociskowa, type FM, umieszczona in nut, It allows odpowiednie pressing tubes metric for fittings (fittings). Material: AISI 316.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrew-together ferrule for hoses termoplastycznych type SAE100R7, MT1, MTH1, OL7M or VE7M. Use only with fittings screw-together from the same supplier (TI-S...). Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA profiled seal according to DIN3869 for high-pressure fittings with a metric and/or inch thread according to DIN 3852-11E. Material: Viton, hardness 80 acc. to Shore'a.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose medium wall thickness intended for extraction and conveying powders, grains, light granulates and other bulk materials. intended for use in industry food and pharmaceutical. used m.in. for milk in powder, grain, rice, coffee, tea, flour (version PAS). pliable, fairly compressible, almost smooth inside, flexible also in low temperatures. O sound resistance to abrasion, resistant to microbes and hydrolysis. non-toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. hose Available is in following versions: P7 OL PU FOOD – spiral with wire steel (copper-plated); P7 L PU PAS FOOD – spiral of steel stainless, Material hose permanently antistatic (R ≤10 8 Ω, in accordance with TRGS 727). hoses P7 OL PU FOOD and P7 L PU PAS FOOD are compliant with requirements European 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. are suitable for time contact with food at conveying dry, bulk, free of fat on surface, substances food - on conditions defined in declaration conformity the manufacturer (Available in Tubes International). Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.7 mm. Reinforcement: spiral with wire steel (P7 OL PU FOOD), spiral with wire of steel stainless AISI 301 (P7 L PU PAS FOOD). Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for oil hydraulic systems, gases, air, fuels, water-based fluids. Inner layer: polyester. Reinforcement: an aramid braid + a steel braid. Outer layer: micro-perforated polyurethane. Working pressure: from 175 bar to 500 bar, depending on the hose diameter. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrength, light and very flexible (also in low temperatures) hose suction-delivery designed specially for industry wine for heavier conditions use. strong than hose SPIRABEL ® SNTS, o thicker wall. hose for demanding applications, intended for conveying water, beer, good win and alcohols with a concentration up to 50% and temperature up to +40°C, juices, drinks and other products food. Not contains phthalates, co allows use go also for milk and its dairy products. not recommended for oils and greasy substances food. Reinforcement spiral with hard PVC, resistant on impact, ensures very good strength on vacuum and kinking hose. transparent wall allows on easy control visual movement substances. smooth surface inner reduces losses flow and ensures ease cleaning. ease cleaning, ensures also smooth surface outer, which available in hoses for diameter 63 mm. W use not regarding direct contact with food (in industry, construction, agriculture) It can be used: 1) for light chemicals, water, sludge and sewage, other liquids (without fat, oils and hydrocarbons); 2) for air, vacuum conveying dusts, powders, granulates and other lightly abrasive substances bulk (not greasy). In that case the abrasiveness and the possible problem of static electricity must be taken into account. as hose reinforced spiral with hardened PVC (without braid) is characterized a certain elongation under pressure, co should take into account in use, especially in temperatures above +40°C. Standards and requirements: Food industry, food contact: compliant with the European requirements 1935/2004/EC and 10/2011/EU (simulant fluids A, B, C and D1), 2023/2006/EC (GMP). Hose material: transparent PVC. Reinforcement: spiral with hardened PVC. Working pressure: from 5 bar to 7 bar, depending on the diameter hose. Operating temperature: -25°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA high-quality NiTO water quick coupling plug 3/4" with a thread external, for a spray gun NiTO I. Material: brass chrome-plated. Working pressure: up to 25 bar. Operating temperature: up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBuckles for the system band Band-It® Standard. Buckles with so-called "noses" secure the end of the band after bending. Material: steel AISI 304.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal ball valve type 4354 intended for installations industrial. can be used for air, gases, water, chemicals, products petrochemical, itp., taking into account chemical resistance material valve and sealing. Meets the requirements of the PED 2014/68/EU directive. Working pressure dependent is od temperature use. Material the body: brass nickel-plated. Material the ball: brass chrome-plated. Material lever: aluminum. sealing the ball: PTFE. sealing stem: FKM + NBR. connection: BSP female/BSPT male. Operating temperature: from -20°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve butterfly, wafer-type, centric, type WAFER, intended for gas installation industrial, in class pressure MOP5. can be closed and opened manually or using actuator pneumatic. handle sets valve in 9 positions: „open”, „closed” and in positions intermediate. meets requirements the directive PED 2014/68/UE. has certificate NF ROBGAZ on compliance with standards EN 13774 and EN 549. Material body: cast iron spheroidal EN-GJS-500-7, coated epoxy 250 ÷ 300 µm. Material disc: cast steel stainless CF8M (for DN100), cast iron spheroidal EN-GJS-500-7 (od DN125). Material stem: steel stainless AISI 420. Material lever: aluminum. sealing disc and stem: NBR. Connection: flange PN10/PN16 for DN32 ÷ DN200, ASA150 for DN40 ÷ DN200. Operating temperature: od -20°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve with connection NAMUR adjustable electrically, is used to control drives pneumatic. Ich connection allows na mounting valves directly na body actuators. Function 5/2 - five-way, two-position. Material: body valve - aluminum, spool - aluminum nickel-plated, sealing - NBR, Cover end - Hostaform®. pressure working: 2.5 ÷ 10 bar. Operating temperature: -10°C up to +60°C. flow nominal: 1100 l/min (at pressure inlet 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal valve check type 2280 intended for installation industrial, It can be used for air, gases, water, chemicals, products petrochemical, etc., taking into account resistance chemical material valve. valve can be mounted in any position, in accordance with direction flow the medium indicated on body. maximum pressure working fixed in full the scope temperatures use. Body material: brass. Material spring: steel AISI 302. butterfly valve: POM. sealing butterfly valve: NBR. Connection: BSP female. Operating temperature: od -10°C up to +90°C. minimal pressure opening: 0.02 bar for 3/8" ÷ 2.1/2"; 0.1 bar for 3" ÷ 4".
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSwivel coupling angled 90° GG90 with bearing ball intended for oil hydraulic. used in systems demanding connections swivel in order to eliminating stresses hoses. coupling intended for performing revolutions at small moment swivel. Not is designed for use with large speeds swivel. Material: steel galvanized. sealing: NBR. Connection: male / BSP female or NPT. Operating temperature: od -40°C up to +106°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSwivel joint with three independent paths, BSP female threads at the inlet and BSP female threads at the outlet. Working pressure: 12 bar. Operating temperature: from -10°C to +80°C. Material: nickel-plated brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting push-in straight with a male NPT thread, series S, type PCC. economical solution for connecting flexible hoses pneumatic o inch calibrated diameter outer. easy and fast in use. Material: plastic plastic. Working pressure: 10 bar. Vacuum: 0.99 bar. Operating temperature: od 0°C up to +60°C. sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter Two-part long for high-pressure equipment washing with connection metric M22x1.5. Z an O-ring po obu sides the connection. Material: brass. pressure working: up to 280 bar. Operating temperature: up to +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure adapter type A101 with BSP male thread (60° cone sealing). Material: AISI 316L.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery light and flexible hose intended for discharge air, dust, dusts, fine sawdust and chips, very light bulk materials etc. Dla all types industry, in particular often used for dedusting and discharge fine particles solid in industry wood, furniture, ceramic, plastics. very pliable and very compressible axially, flexible also in low temperatures. O sound resistance to abrasion, resistant also on microbes and hydrolysis. Not toxic, Contains no halogen compounds or plasticisers. Resistant to oils and petrol. hose marked is an arrow indicating correct direction flow medium. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. hose Available is in following versions: ECO – version standard, ECO SE – version with material flame-retardant (without classification flame retardancy), ECO AS – version permanently antistatic (ISO 8031: R 9 Ω, TRGS 727 (6.4.2.4): R 8 Ωm, directive 2014/34/EU (ATEX): It can be used in defined zones hazard explosion po analysis risk, ECO SE AS – version antistatic and flame-retardant (Available on special order). hose ECO produced is in process production compliant with with policy sustainable growth in which uses raw materials originating with recycling pure waste with process production, energy renewable, closed circulation water and other innovation. Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Wall thickness measured between the spiral: 0.4 mm. Operating temperature: od -40°C up to +100°C (momentarily for + 125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDistribution manifold with Ø 4-6-8 mm fittings for use in pneumatic systems, allowing pressurized compressed air to be split into several branches. It has additional holes for fixing it at the desired point of the installation. Working pressure: 12 bar. Operating temperature: from -10°C to +80°C. Material: anodized aluminum.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle extended bent o diameter hole 2.3 mm for guns for air, terminated a thread metric M12x1.25. Material: steel nickel-plated. Maximum pressure: 10 bar. Operating temperature: from -10°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket coupling CAMLOCK B with a BSPT male thread made in accordance with the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer coupling, especially in the petrochemical industry. Working pressure: up to 7 bar, depending on the coupling size. Material: polypropylene glass-fiber-reinforced. Levers: steel AISI 304. Sealing: EPDM.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA set of replaceable seals for a compact actuator ISO 21287, LINER series. Material: polyurethane. Diameter: 20, 25.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting hydraulic screw-together, type S, with metric female thread with a nut, sealing metal - metal on a 60° cone, (DKM). intended for screwing onto hoses rubber and termoplastycznych using a ferrule screw-together. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLance for foam assembled with a plug quick coupling DN 11.8, without nozzle. Connection: (inlet) plug DN11.8 / (outlet) 1/2" BSP female. available length: 22 cm, 50 cm and 60 cm. Material: steel stainless.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA DIN 3015 standard clamp, type 100 (without a top plate) intended for quick, easy, durable and aesthetic mounting of pipes, cables and hoses in various branches of industry, in above-ground and marine installations. Made in accordance with the DIN 3015 standard. The clamp is mounted to the structure by welding the clamp base (it is also possible to bolt it on or mount it on a rail). As standard, the clamp has a profiled (grooved) surface of the pipe hole. For dimension group 0 there is one bolt with an Allen head, for dimension groups 1 ÷ 6 there are two bolts with an Allen head. In addition to the standard metal element, you can order: extension plates, rails and bolts for mounting clamp sets. The selection of element should be consulted with TUBES INTERNATIONAL®. Material clamp: rubber. Material bolts: steel galvanized. Material base: steel carbon. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure Water gun SG35 with lance MT8 for applications industrial. Suitable for warm and cold water. The lever mechanism does not require the operator to use much force, which translates into comfortable and pleasant work. part outlet lance terminated a thread internal metric M22x1.5. lance made of steel stainless or galvanized. The gun is also available with a swivel connection to the installation. Housing material: high-strength plastic. Working pressure: up to 310 bar. pressure The permissible: 350 bar. Flow rate: 45 l/min. Operating temperature: up to +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDurable hand pliers intended for installing CAW type or similar clamps (with 1 or 2 "ears"). The jaw profile allows easy and reliable front and side crimping.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTape o double loop with built-in a buckle system Band-It® Ultra-Lok® made of steel AISI 201 intended for most demanding applications. double loop increases strength clamps. A band with a smooth surface and its correct installation on a non-serrated hose creates a tight fixing of the fitting, preventing leaks into the inside of the clamp. installing using tools electrical BD-UL9010 or BD-UL4000B. Do mounting straps 1/2" for devices mounting should use washer adjustment BD-M09387. Material: steel AISI 201.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction-delivery for demanding, versatile applications in industry food. excellent for conveying many types products food such as: olive oil, wine, beer, juices fruit, milk, fats and alcohols with a concentration up to 96%. The inner layer is free of phthalates, plasticisers and components of animal origin. Contains no phthalates or bisphenol A and no polycyclic aromatic hydrocarbons (PAH Free), in accordance with ZEK 01.4-08 Cat.1. Tested for the presence of heavy metals. Layer outer resistant to conditions atmospheric and ozone. thanks to external corrugation hose is exceptionally pliable and flexible. recommended way mounting with fitting are special clamp shell EASY SHELL, o shape adapted for serrated hose. standards and requirements : industry food, contact with food 1935/2004/EC and EC 2023/2006/EC (GMP). Layer inner compliant with FDA 21 CFR 177.2600, BfR XXI kat. 2, D.M. 21/03/73, 3-A Sanitary Standard 18-03 class II. Inner layer: white, smooth synthetic rubber. Reinforcement: cord synthetic, spirals steel. Outer layer: blue synthetic rubber. Working pressure: 10 bar. Vacuum: 0.6 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAnaerobic sealant for pipes and flanges (with PTFE). is characterized high viscosity and medium strength. has certificate DVGW - approval for installation gas and hot water. has certificate KTW - approval for installation water potable. possible disassembly at use ordinary tools. maximum size thread: M 80. Operating temperature: -60°C up to +150°C. Packaging of the "pen" type with a capacity of: 50 ml.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for solvents, paints, isocyanate, polyol, gases, air, water-based fluids. standards: SAE 100R7, ISO 3949-R7. Inner layer: polyamide. Reinforcement: a double polyester braid. Outer layer: micro-perforated polyurethane. Operating temperature: from -40°C to +100°C (for water and air up to +70°C).
