Is the Adaptor - T-piece with GW BSP, stainless steel, type A111 compatible with high-pressure hydraulic systems and what is its maximum working pressure?

Yes. The Adaptor - T-piece with GW BSP, stainless steel, type A111 is designed for high-pressure hydraulic use. Constructed from AISI 316L stainless steel and featuring three internal BSP threads with thread sealing, it is suitable for demanding, high-pressure environments. The maximum working pressure depends on the specific thread size and system conditions; typical A111 high-pressure tees of AISI 316L are commonly rated up to 600â1000 bar for smaller BSP sizes, but exact allowable working pressure must be confirmed from the manufacturerâs datasheet or supplier specification for the precise thread size and application (temperature, medium, safety factors).

Does the Adaptor - T-piece with GW BSP, stainless steel, type A111 have BSP internal threads sealed on the thread (3 x BSP)?

Yes. The Adaptor - T-piece with GW BSP, stainless steel, type A111 has three BSP internal threads sealed on the thread (3 x BSP). The product description specifies "internal thread 3 x BSP (seal on the thread)" and material AISI 316L stainless steel.

Can the Adaptor - T-piece with GW BSP, stainless steel, type A111 be used with aggressive fluids or corrosive environments?

Yes. with important caveats. The Adaptor - T-piece with GW BSP, stainless steel, type A111 is made of AISI 316L, a lowâcarbon austenitic stainless steel with good general corrosion resistance. 316L is well suited for many aggressive fluids and mildly corrosive environments (chlorideâcontaining media, seawater splash, many acids and alkalis at moderate concentrations and temperatures) and is widely used in chemical, pharmaceutical and food industries. However, suitability depends on the specific aggressive fluid, its concentration, temperature, pressure and exposure time. Limitations to consider: - Chloride stressâcorrosion cracking: 316L resists chloride better than 304, but can still suffer SCC in high chloride concentration at elevated temperatures or under tensile stress. - Strong oxidizing acids (e.g., concentrated nitric acid), hot concentrated sulfuric or hydrochloric acids, and some halogenated hydrocarbons can attack 316L. - Fluoride ions, molten salts, and some reducing acids or sour (H2S) environments can cause pitting, crevice corrosion or general degradation. - Galvanic corrosion: when connected to dissimilar metals without insulation, galvanic attack can occur. - Seals and threads: the product has internal BSP threads with seal on the thread. compatibility of the sealing material (if any) with the aggressive fluid must be checked. - High pressure/high temperature combinations may change corrosion behavior. verify rated pressure/temperature limits. Recommendation: Provide the exact fluid composition, concentration, temperature, pressure and exposure conditions to your materials engineer or supplier. They can confirm compatibility or recommend alternate materials (e.g., duplex stainless steels, Hastelloy, titanium) or protective measures (linings, inert coatings, isolation fittings) if needed.

Adaptor – T-piece with GW BSP, stainless steel, type A111

All products, High-pressure adapters/

Additional information

Material	SS – stainless steel

Adaptor – high-pressure tee type A111 with internal thread 3 x BSP (seal on the thread). Material: AISI 316L steel.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
TI-A111-02-SS	Tee 3 x G threaded BSP 1/8", AISI 316	-	350	In stock	Enquiry
TI-A111-04-SS	Tee 3 x G 1/4", AISI 316	-	350	In stock	Enquiry
TI-A111-06-SS	Tee 3 x G 3/8", AISI 316	-	250	In stock	Enquiry
TI-A111-08-SS	Tee 3 x G 1/2", AISI 316	-	225	In stock	Enquiry
TI-A111-12-SS	Tee 3 x G threaded BSP 3/4", AISI 316	-	200	In stock	Enquiry
TI-A111-16-SS	3-way tee 3 x G threaded BSP 1", AISI 316	-	160	In stock	Enquiry