Is the F0200 polyester braided thermoplastic hose suitable for use with hydraulic oil, air, and fuels across its specified temperature range?

Yes. The F0200 polyester braided thermoplastic hose is suitable for hydraulic oil, air, and many fuels across its specified temperature range, with the following considerations: - Media compatibility: Designed for hydraulic oil installations, gases, air, fuels and water-based fluids.explicitly listed in the product description. - Temperature limits: Rated -40Â°C to +93Â°C overall. For water and air the max temperature is limited to +65Â°C; other listed media (hydraulic oil, many fuels) may be used up to the +93Â°C limit unless specific fluid compatibility data from the fluid or hose manufacturer indicates otherwise. - Pressure and construction: Double polyester braid reinforcement and working pressures from 77 to 235 bar (depending on diameter) make it suitable for typical hydraulic and fuel systems and pneumatic applications within those pressure ratings. - Standards: Conforms to DIN 24951, SAE 100R7, ISO 3949-R7, supporting use in these service types. Recommendation: Verify compatibility for specific hydraulic fluids or specialty fuels (e.g., biofuels, aggressive additives) and confirm working pressure and temperature for your hose diameter and system conditions before final selection.

Can F0200 polyester braided thermoplastic hose be used with water-based fluids at up to +65Â°C and still meet DIN 24951/ISO 3949-R7 standards?

Yes. F0200 polyester braided thermoplastic hose can be used with water-based fluids up to +65Â°C and still meet DIN 24951/ISO 3949âR7 standards. The hose specification lists operation from â40Â°C to +93Â°C, with a specific note that for water and air the maximum recommended temperature is +65Â°C, and the product is explicitly designed for waterâbased fluids while complying with DIN 24951 and ISO 3949âR7. Ensure correct diameter and working pressure rating (77â235 bar depending on size) for your application.

Can F0200 polyester braided thermoplastic hose handle pulsating pressures up to its 235 bar rating?

No. F0200 polyester braided thermoplastic hose should not be assumed to handle continuous highâfrequency pulsating pressures up to its static 235 bar working pressure without further verification. Explanation: The listed 235 bar is the nominal working (maximum operating) pressure for certain diameters under steady (static) conditions per the standards cited (DIN 24951, SAE 100R7, ISO 3949âR7). Those standards and the construction details (polyester inner layer, double polyester braid reinforcement, microâperforated polyurethane cover) indicate suitability for hydraulic oil, gases, air, fuels and waterâbased fluids within the stated temperature range, but they do not automatically certify resistance to highâamplitude or highâfrequency pulsation or pressure spikes. Why pulsation matters: Repeated pulsating loads cause dynamic fatigue in the reinforcement braid and inner tube, raising the risk of premature wear, braid separation or hose failure even if peak pulses do not exceed the static rating. Polyester braid has good strength but lower fatigue resistance than some synthetic fibers or steel wire reinforcements for severe pulsation duties. What to do: - Consult the manufacturerâs technical datasheet or application engineer for explicit pulsation/fatigue ratings, recommended safety factor, and maximum allowable pulse amplitude and frequency for the specific F0200 hose size. - If pulsation is significant, consider hoses specified for pulsating service (e.g., steelâwire or specially tested braided hoses) or add dampening (accumulators, pulsation dampers, pressure relief devices). - Follow recommended installation practices (proper bend radius, support, avoid torsion) and perform regular inspections. Conclusion: Use caution. verify with the manufacturer or choose a hose rated and tested for pulsating pressures rather than relying solely on the static 235 bar rating.

F0200 polyester braided thermoplastic hose

All products, Thermoplastic hoses/

Additional information

Material	PEE – polyester
Maximum operating temperature [°C]	93
Minimum operating temperature [°C]	-40
Vacuum resistance	check

Lightweight, flexible hose designed for hydraulic oil installations, gases, air, fuels, water-based fluids. Standards: DIN 24951, SAE 100R7, ISO 3949-R7. Inner layer: polyester. Reinforcement: double polyester braid. Outer layer: micro-perforated polyurethane. Working pressure: from 77 bar to 235 bar, depending on hose diameter. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
MC-F0200A-04	Thermoplastic hose F0200A 1/8"	4	235	In stock	Enquiry
MC-F0200B-05	Thermoplastic hose F0200B 3/16"	5	220	In stock	Enquiry
MC-F0200C-06	Thermoplastic hose F0200C 1/4"	6	215	In stock	Enquiry
MC-F0200D-08	Thermoplastic hose F0200D 5/16"	8	195	In stock	Enquiry
MC-F0200E-10	Thermoplastic hose F0200E 3/8"	10	187	In stock	Enquiry
MC-F0200F-13	Thermoplastic hose F0200F 1/2"	12	157	In stock	Enquiry
MC-F0200G-16	Thermoplastic hose F0200G 5/8"	16	130	In stock	Enquiry
MC-F0200H-19	Thermoplastic hose F0200H 3/4"	20	105	In stock	Enquiry
MC-F0200I-26	Thermoplastic hose F0200I 1"	25	77	In stock	Enquiry

Do you need a larger quantity of products or a bespoke quote?

Call us: +48 61 653 02 22 or email us: tubes@tubes-international.com

SEND ENQUIRY

Lightweight, flexible hose designed for hydraulic oil installations, gases, air, fuels, water-based fluids. Standards: DIN 24951, SAE 100R7, ISO 3949-R7. Inner layer: polyester. Reinforcement: double polyester braid. Outer layer: micro-perforated polyurethane. Working pressure: from 77 bar to 235 bar, depending on hose diameter. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).