Is the End with GZ BSP, 45Â° inner cone, brass, type EW suitable for continuous use at 40 bar and temperatures from -10Â°C to +90Â°C?

Yes. End with GZ BSP, 45Â° inner cone, brass, type EW is specified for a working pressure of 40 bar and an operating temperature range of -10Â°C to +90Â°C, so it is suitable for continuous use under those exact conditions. Ensure installation follows manufacturer instructions and consider system factors (dynamic pressure spikes, corrosive media, wear, sealing compatibility) that could affect long-term performance.

Can End with GZ BSP, 45Â° inner cone, brass, type EW withstand occasional pressure spikes above 40 bar within -10Â°C to +90Â°C?

End with GZ BSP, 45Â° inner cone, brass, type EW Format: The specified working pressure is 40 bar and operating temperature range is -10Â°C to +90Â°C. Occasional spikes above 40 bar exceed the rated working pressure and therefore cannot be guaranteed safe-brass fittings may deform, leak or fail under overpressure, especially repeatedly or if spikes are significant. If spikes are small and very rare, risk might be low but is still present; for safety and compliance, use a fitting rated above the maximum anticipated spike or install pressure-limiting/protection devices.

Can End with GZ BSP, 45Â° inner cone, brass, type EW be used with aggressive hydraulic fluids at 40 bar and -10Â°C to +90Â°C?

End with GZ BSP, 45Â° inner cone, brass, type EW Format may be acceptable for use with aggressive hydraulic fluids at 40 bar and â10Â°C to +90Â°C only if the specific fluid is compatible with brass and any seals used. The fittingâs rated working pressure (40 bar) and operating temperature range (â10Â°C to +90Â°C) match your conditions. However, key considerations: - Corrosion/chemical compatibility: Brass can be attacked by some aggressive fluids (e.g., certain acids, ammonia, hydrogen sulfide, some synthetic fluids or additives). Verify the fluidâs compatibility with brass (Cu/Zn alloys) using manufacturer chemical compatibility data. - Seals and elastomers: The fitting likely uses seals or O-rings whose material (not specified) must be compatible with the fluid and temperature range. Incompatible seal compounds can swell, harden or fail. - Cavitation/erosion and additives: Aggressive or abrasive additives can cause accelerated wear of brass. Some aggressive fluids may leach alloy components or degrade mechanical properties over time. - System safety margin: Continuous operation at the rated limits and transient spikes above 40 bar or outside temperature range reduce safety; consider derating or using materials with greater corrosion resistance (e.g., stainless steel) if risk is significant. - Certification and supplier guidance: Follow supplier datasheets and, if necessary, request chemical compatibility confirmation or testing for the specific fluid and temperature profile. Conclusion: Technically the fittingâs pressure and temperature ratings match your stated conditions, but you must confirm chemical compatibility of brass and of the fittingâs seals with the specific aggressive hydraulic fluid before approval. If in doubt, choose a corrosion-resistant material (e.g., stainless steel) or obtain manufacturer confirmation.

End with GZ BSP, 45° inner cone, brass, type EW

All products, Low-pressure fittings and adapters/

Additional information

Material	B – brass (bronze)

BSP external thread fitting, internal cone 45°. Material: brass. Working pressure: 40 bar. Operating temperature: from -10°C to +90°C.

List of product variants

Article number	Product variant name	DN	BAR	Availability	Actions
EW-MS-11325	End fitting with GZ 3/4" BSP, hose 9 mm, 45° cone, brass	10	40	In stock	Enquiry
EW-MS-11326	End fitting with GZ 3/4" BSP, hose 13 mm, 45° cone, brass	12	40	In stock	Enquiry
EW-MS-11327	GZ 3/4" BSP fitting, 19 mm hose, 45° cone, brass	20	40	In stock	Enquiry
EW-MS-11328	End fitting with 1" BSP, hose 19 mm, 45° cone, brass	20	40	In stock	Enquiry
EW-MS-11329	1" BSP end fitting, 25 mm hose, 45° cone, brass	25	40	In stock	Enquiry
EW-MS-11330	End fitting with 1" BSP, hose 32 mm, 45° cone, brass	32	40	In stock	Enquiry
EW-MS-11331A	End fitting with GZ 1/4" BSP, hose 6 mm, 45° cone, brass	6	40	In stock	Enquiry
EW-MS-11332A	End fitting with GZ 3/8" BSP, hose 6 mm, 45° cone, brass	6	40	In stock	Enquiry
EW-MS-11334A	GZ 3/8" BSP fitting, 9 mm hose, 45° cone, brass	10	40	In stock	Enquiry
EW-MS-11340A	1/4" BSP end fitting, 9 mm hose, 45° cone, brass	10	40	In stock	Enquiry
EW-MS-11341	End fitting with GZ 1/8" BSP, hose 4 mm, 45° cone, brass	4	40	In stock	Enquiry
EW-MS-11343	GZ 3/8" BSP end, 13 mm hose, 45° cone, brass	12	40	In stock	Enquiry
EW-MS-11344	GZ 1/2" BSP fitting, 13 mm hose, 45° cone, brass	12	40	In stock	Enquiry
EW-MS-11351	End fitting with GZ 1/8" BSP, hose 6 mm, 45° cone, brass	6	40	In stock	Enquiry
EW-MS-11352	End fitting with GZ 1/8" BSP, hose 9 mm, 45° cone, brass	10	40	In stock	Enquiry
EW-MS-11366	End fitting with GZ 1/2" BSP, hose 9 mm, 45° cone, brass	10	40	In stock	Enquiry
EW-MS-11367	End fitting with GZ 1/2" BSP, hose 6 mm, 45° cone, brass	6	40	In stock	Enquiry
EW-MS-11368	End fitting with GZ 1/4" BSP, hose 4 mm, 45° cone, brass	4	40	In stock	Enquiry
EW-MS-11371	End fitting with GZ 1/4" BSP, hose 13 mm, 45° cone, brass	12	40	In stock	Enquiry