Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA high-quality NiTO water quick coupling socket 1" with a female thread and a shut-off valve. Material: brass chrome-plated. Working pressure: up to 25 bar. Operating temperature: up to +80°C. Sealing: NBR (not suitable for gasolines and oils). For the valve, an EPDM O-ring.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA BCS quick coupling socket without a valve, with a female BSP thread, for lances, guns and washing equipment. Material: steel stainless. pressure working: 400 bar. Operating temperature: +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium size socket quick coupling with a nut na hose, intended for installations washing, filtration water deionized, machines industrial, detection leakage, itp. The characteristic design (it does not contain balls and a locking sleeve) allows easier, secure one-hand connection and disconnection. An audible click signals a successful connection. Length L - total length. Material: acetal. Sealing: O-ring with NBR. Working pressure: for 8.3 bar. Operating temperature: from -40°C to +82°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAnaerobic adhesive fixing - hard removable general use. quickly cures, time fixing for steel ok. 4 min. use for fastening on shafts and gears toothed, wheels fitted and element coaxial. prevents loosening connections and leakage caused loads impact and vibrations. works not only on active metals, ale also on surfaces passive e.g. steel stainless. product tolerates light oiling and light contamination surface. color: green. Working temperature range: od -55°C up to +180°C. strength on shearing at tension: > 25 N/mm². Time to reach initial strength: 5-30 min. Time to reach full strength: 6-72 h (depending on material). compliant with German the standard DVGW(EN 751-1): NG-5146AR0619. Packaging - pen 50 ml.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsElbow silicone 45° reinforced polyester intended is for systems cooling and systems heating in vehicles (water, liquids cooling, air clean or with small amount mist oil). For oils, fuels and oil mist, a version with a fluorosilicone inner layer is recommended. Arm length: 100 mm (also available with arms of length 152, 250 mm). Pressure safety factor: 3:1. The hose meets the SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. color layer outer: blue. Material: rubber silicone. Reinforcement: polyester plies. pressure working: od 1.5 bar for 8.33 bar (depending on diameter hose). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting 90° ORFS INTERLOCK with UNF female thread, flat sealing, for hose type 4SH, R13 and R15. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAngled BANJO fitting 90° type RBR, intended for low-pressure rubber and plastic hoses, unreinforced and with textile reinforcement, with an external steel braid. Commonly used in flexible lines for sanitary fittings, fuel and air installations, etc. Material: carbon steel, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight hose fitting, type NA with a BSPT and metric male thread. Intended for use in control systems, in installations for the transport of gases and liquids, in vacuum installations, etc. Working pressure: up to 10 bar. Material: polyamide (PA6).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA VB plug for TW (tankwagen) transfer couplings. used for parts MK (female), constitutes a cap resistant na pressure. Material: brass. Operating temperature: from -20°C to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, thick, flexible hose intended for extraction and conveying abrasive bulk materials: granulates, grain, sand, gravel. thick wall and very dense spiral reinforcing ensures high resistance to pressure and vacuum. very smooth inside, non-compressible, not very pliable (r=4xD), retains its flexibility also in low temperatures. hose o sound resistance to abrasion, resistant also on oils and gasoline. Assembly on connectors with bridge clamps (prawo-handed) or assembly special on ends industrial e.g. flange. Other diameters may be available on special order. versions: P3 S PU – version standard, with polyester – polyurethane, very resistant to abrasion and P3 S PU AE - version with polyether – polyurethane, o sound resistance to abrasion, resistant to microbes and hydrolysis; with approval for contact with substances food, compliant with requirements European 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. is suitable for time contact with food at conveying dry, bulk, free of fat on surface, substances food - on conditions defined in declaration conformity the manufacturer (Available in Tubes International); P3 S PU AS – version antistatic (R ≤10 8 Ω), compliant with TRBS 2153 and for extraction also with TRGS 727, with polyether – polyurethane, o sound resistance to abrasion, resistant to microbes and hydrolysis. Hose material: transparent polyester-polyurethane (P3 S PU), transparent polyether-polyurethane (P3 S PU AE and P3 S PU AS). Wall thickness measured between the spiral: 2 mm. Reinforcement: dense spiral with wire steel. Operating temperature: od -40°C up to +100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA DIN 3015 standard clamp, type 101 (with a top plate) intended for quick, easy, durable and aesthetic mounting of pipes, cables and hoses in various branches of industry, in above-ground and marine installations. Made in accordance with the DIN 3015 standard. The clamp is mounted to the structure by welding the clamp base (it is also possible to bolt it on or mount it on a rail). As standard, the clamp has a profiled (grooved) surface of the pipe hole. A clamp with a smooth hole surface is also available, intended for hoses and cables, marked with the letter H at the end of the index code. For dimension group 0 there is one bolt with a hexagonal head, for dimension groups 1 ÷ 6 there are two bolts with a hexagonal head. In addition to the standard metal element, you can order: extension plates, rails and bolts for mounting clamp sets. The selection of element should be consulted with TUBES INTERNATIONAL®. Material clamp: aluminum. Material bolts: steel galvanized. Material plate: steel galvanized. Material base: steel carbon. Operating temperature: up to +350°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA clamp tubular type UNI-FLEX S Intended for connecting and repairs pipes metal and plastic (connection axially not fixed, flexible - only with gasket rubber). Application: water, gaz, oils and fuels, other carbon, air. version material: steel AISI 316Ti (housing, screws - Class A4-80, solid pins). sealing: NBR rubber. Operating temperature: od -20°C up to +80°C. pressure nominal: PN 16 (Class pressure working for applications in industry shipbuilding, marine; Safety factor 4:1, assuming positive result single-use testing pressure four times greater, ale po which A clamp not can be used again). maximum Working pressure: 25 bar (for remaining applications industrial and conditions static; factor safety 1.5:1, assuming positive result testing pressure 150% maximum pressure working, po which A clamp can be further repeatedly used). value pressures working apply for mounting clamps on round tubes steel o minimum wall thickness wall, mounting in accordance with instructions and tightening a wrench torque given on a clamp torque).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAn AKBO HEAVY DUTY water gun. Made of stainless steel, insulated trigger, EPDM rubber guards, Viton seals. It has an adjustable outlet nozzle, smooth flow regulation and a trigger lock. Connection: 1/2" BSP female. The version with a trigger guard bow protects against uncontrolled opening of the water stream and against damage. maximum Working pressure: 24 bar. Maximum Operating temperature: +95°C. weight: ok. 0.87 kg. Flow rate: 30 l/min (5 bar), 75 l/min (24 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA displacement gear pump (hydraulic), TRALE, with external gearing, intended for use in the hydraulic systems of machines and equipment. Connections: flange. Direction of rotation: right. The stated maximum working pressure applies to continuous operation. Material: body and mounting plate – aluminum, rear cover – aluminum. Sealing: NBR. Medium: L-HM45 type hydraulic oil or equivalent. Fluid viscosity: from 10 cSt to 600 cSt (recommended 30 ÷ 45). Operating temperature: from -20°C to +90°C (medium), from -20°C to +60°C (ambient).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsButton flat monostable VRM-010 RN for valve VME. For mounting, the VME1-000 adapter is required.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReducer symmetrical (reducer concentric) for welding butt for applications pressure made with pipes seamless, compliant with the standard EN 10253-2B (steel carbon). With an EN 10204 3.1 material certificate. Widely used in industry in the construction of installations and pipelines, among others as element of complete welded ends for metal and rubber hoses (welded with threaded and flanged ends) and other couplings and fittings. On request, other sizes and materials are also available, including reducers of more than two DN sizes and ASME reducers. fittings type B (EN 10253-2B) have full resistance pressure corresponding pipe o the same diameter D and wall thickness wall T. Na special order Available are other types fittings for welding-on butt: elbow 45° and 180°, reducers eccentric, tees, caps. Material: steel carbon P235 GH. Working pressure: od 71 up to 224 bar - depending on diameter.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe EAR CLIP-W clamping ring is an improved version of the EARCLIP ring. It has an internal protective insert whose role is to protect the hose surface at the ring's clamping point and provide more even pressure around the circumference. Recommended for hoses of delicate construction. Rounded edges inside the ring protect the hose from damage. Material: galvanized carbon steel (main ring), AISI 301 stainless steel (insert).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTee "T", 2x BSP female thread, 1x BSPT male thread, type A12, intended for connecting pneumatic components (including hoses) to one another. A tight connection usually requires additional sealing: PTFE tape or sealant for a tapered thread, or aluminum or copper washers for a parallel thread. Material: nickel-plated brass. Working pressure: 60 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTee plug-in "T" adjustable with a thread external, type R32, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSleeve mounting crimped for thick-walled hoses for freon, type 2051A. Material: aluminum.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsKnown and proven od lat, light and soft hose with rubber natural o light brown color. easy for installation thanks to its softness (hardness 40° Shore – A), flexible and flexibility (Maximum stretchability 500%). has close properties for latex. resistant na abrasion, o sound resistance na acids and bases. used for liquids and gases, for many applications industrial np. dispensing and dosing soaps and detergents, products alcoholic and milk, laboratories. Sterilization steam 30 min. (1 bar, 141°C) or oxide ethylene. length full roll hose 50 m (od diameter internal 7 mm - 25 m). The given working pressure is determined relative to the bursting pressure at a safety factor of 1:5. Material: rubber natural (NR). temperature use: from -35°C to +70°C (120°C for moist hot). temperature brittleness: -40°C. Hardness: 40° Shore (A). Density: 0.98 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA device intended for cutting hydraulic hoses 1 and 2 braid for diameter internal 2” and 4 braid for diameter 1.1/4”. used in workshops and cars service. Maximum Diameter outer hose: 80 mm. Drive: three-phase motor 400V, 3kW or (different version devices) supply battery 12 / 24V 1.1 kW. speed rotational: 2880 obr/min. Standard cutting disc: Ø 300 x 3 x 50 mm – smooth (a toothed disc can be used). weight 45 kg. Possibility of connection to an extraction system (Ø 63 mm).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose suction-delivery intended for conveying products pharmaceutical, cosmetic, substances food, chemical (selection in accordance with rules acc. to chapter "hoses chemical"). Contains no plasticisers, phthalates or substances of animal origin. is characterized high strength thermal and mechanical. is excellent solution for industries processing demanding highest safety during transfer products o high cleanliness. Layer outer resistant to abrasion, ozone and conditions atmospheric. has two copper cable ensuring continuity electrical between fitting hose. standards and requirements : 1) general EC 2002/95 (RoHS), EC 1907/2006 (REACH). 2) industry food, contact with food 1935/2004/EC and 2023/2006/EU (GMP). Layer inner compliant with 10/2011/EC, D.M. 21/03/73, FDA 21 CFR 177.1550. Layer outer compliant with FDA 21 CFR 177.2600, D.M. 21/03/73. 3) Pharmaceutical industry: USP CLASS VI (Layer inner). assembly : smooth ends with a spigot ("tail" into the hose) must be used, without sharp or high barbs that could cut or damage the MFA inner layer after clamping. The spigot diameter should be precisely matched to the hose diameter to ensure tightness. Assembly with clamping ferrules or shell clamps. Inner layer: smooth polymer fluorine MFA. Reinforcement: cord synthetic, steel spiral. Outer layer: smooth EPDM rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: -50°C up to +170°C (for greater chemicals).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic hose with a reduced outer diameter and mass and increased flexibility (COMPACT type). intended for most demanding applications. excellent resistance to pressure pulsating. thanks to special blend rubber Layer outer antistatic, highly flame-retardant (exceeds requirements MSHA), highly resistant to ozone, conditions weather, abrasion and radiation UV. has certificate MSHA. standards: EN 857-2SC, SAE 100R 16S, ISO 11237-1. Assembly: contact TUBES INTERNATIONAL®. Inner layer: black synthetic rubber. Reinforcement: a double steel braid. Outer layer: black synthetic rubber. Working pressure: from 210 bar to 400 bar depending on the diameter hose. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery intended for conveying compressed air, for compressors, hammers, drills and other tools pneumatic. thanks to low weight, flexibility, strong construction and high pressure working accepted and with success used od many lat in construction (in particular in companies occupying demolition), industry and mining. extremely strength and durable thanks to high quality materials and the structure. Reinforcement with circumferentially woven braid polyester completely bonded and surrounded rubber in original process production extrusion blend rubber on hot through braid. resistant to radiation UV. Layer inner smooth, co ensures minimal losses flow. yellow, grooved surface outer is resistant abrasion, oils and ozone and perfectly visible on square construction. flat at rest, co facilitates operation and storage. resistant to loads longitudinal. used most often of couplings claw for air (spacing 42 or 41 mm) mounted clamps cast iron (ordered separately). Available also in color black. use for air under high pressure should be always preceded analysis risk in situation accidental disconnection or bursting hose and possible use protections. maximum pressure working fixed acc. to coefficient safety 4:1 approved through the manufacturer for air. Not recommended exceeding 1/3 given force breaking. length standard roll: 200 m. Hose material: yellow blend NBR/PVC with barrier resistant on UV, pressed in a polyester braid in process extrusion hose. Working pressure: from 12.5 bar to 25 bar - depending on the diameter hose and temperatures. Operating temperature: od -30°C up to +75°C (momentarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMulti-hose in outer cover with black polyurethane, intended for installations pneumatic, hydraulic, oil, fuel, lubrication and chemicals. various color hoses enable easy identification individual circuits supply or various media. amount hoses: 2. Hose material: polyamide PA 12 (nylon). Working pressure: from 7.5 bar to 33 bar (in dependence od diameter and wall thickness wall hose). Operating temperature: od -20°C up to +80°C (for liquids containing water up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible metal hose of steel stainless intended for discharge gases with particles liquids, fumes, vapours, conveying dry bulk materials (ash, dusts, grain, granulates), and as hose cover. mounted in installations outlet exhaust gases engines as element absorbing vibration, noise and reducing effects expansion thermal. version standard stays shape. letter F on the end index means version FLOPPY, not maintaining shape. Material: steel AISI 304. Operating temperature: up to +650°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, popular hose, PVC general use. used for air, water and light chemicals in industry, agriculture, horticulture and for use domestic. Roll length: 60 m. Inner layer: transparent PVC. Reinforcement: a polyester braid. Outer layer: transparent PVC. Working pressure at a temperature of 20°C: from 10 bar to 15 bar - depending on the diameter hose and decreases together with of increase temperatures. Operating temperature: from -5°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHanger intended for easy storage hose 1/2" (20 meters) or 3/4" (20 meters). raises comfort use and increases service life hose. convenience and saving space. Material: electropolished steel AISI 304.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap two-part coupling/valve IBC with a thread internal S60x6, with a removable cap in red; it can be used for screwing on e.g. a spout. Material: polypropylene.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket cap coupling CAMLOCK DP made in accordance with the American military standard MIL-C-27487 (A-A-59326). Working pressure: up to 10 bar, depending on the coupling size. Material: steel AISI 316.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap (plug) ORFS with UNF female thread (sealing on the face surface), type VKA. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap for use in pipe installations industrial. Material: malleable cast iron. Operating temperature: up to +300°C. Working pressure: 25 bar (up to +120°C), 20 bar (up to +300°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCap fitting for the SPEEDFIT system, used in compressed-air installations. Material: plastic plastic. pressure working: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal directional valve with electric control (solenoid valve), without a control coil, most often used for controlling the operation of actuators. It can be mounted in-line, on a wall, directly on actuators or on a connection block. Function 5/2 - five-way, two-position. Material: body valve - aluminum, spool - aluminum nickel-plated, sealing - NBR, Cover end - plastic plastic. pressure working: up to 10 bar. Operating temperature: -10°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve FFP securing configuration hydraulic against loss oil in case sudden depressurisation installation (e.g. rupture line). W during normal use the system, valve allows on Flow rate oil in both directions. W situation sudden rise flow (e.g. rupture line), valve closes Flow rate oil in one direction. permissible direction flow: A → A1 (free), A1 → A (valve). Material: steel carbon, galvanized (body), hardened steel (valve). sealing: metal-metal. Operating temperature: od -30°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA set for foam and rinsing: A gun NITO ERGO, A bowl 2.5 l (Available in various colors) na agent cleaning with injector for foam, a hose suction and set nozzles dosing, lance 17 cm with nozzle for rinsing. max. pressure working: 10 bar. max. temperature use: +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA GUILLEMIN coupling with a female BSP thread intended for industrial and reloading installations for substances, bulk materials and granulates. Not suitable for transferring steam and gases. The coupling has a symmetrical design of the connection part. Made in accordance with the EN 14420-8/NF-E-29572 standard. Material: aluminum. Working pressure: 16 bar. Sealing: white NBR rubber. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling with BSP male thread, type VSLR, for a shell clamp, with serrated tail, EN 14420-3 / DIN 2817 (only clamps RS 636... and RS-637...), for assembly onto industrial hoses – e.g., in handling applications. Working pressure: 25 bar. Coupling material: brass (MS), AISI 316 stainless steel (SS). Sealing: flat (face). Operating temperature: from -20°C to +65°C according to EN-14420.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight A reel type COMPACT in housing plastic for operation in places, where required are small dimensions np. service cars, assembly lines, workbenches, etc.. equipped in hose polyurethane o length 12 m. Available to the standard with bracket swivel. hose main terminated additional spring anti-kink. Material housing: plastic plastic. Operating temperature: up to +50°C.
