Suction and discharge hose intended for the transfer of industrial water, sewage, sludges, non-corrosive liquids, etc. Lightweight, flexible, resistant to kinks and vacuum. The outer layer is resistant to ozone and weather conditions. Commonly used for pumps in industry, construction, and agriculture. Installation – depending on the diameter and type of fittings using clamps, brackets, compression sleeves, tapes. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black SBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black SBR rubber. Working pressure: from 5 bar to 10 bar, depending on the hose diameter. Vacuum: 0.9 bar. Operating temperature: from -30°C to +70°C.

Widely used for washing floors and industrial equipment with hot water. Also suitable for outdoor use. Resistant to weather conditions and abrasion. Not resistant to oil, not recommended for air with oil mist. Compared to the "Tubes 2116," it has a thicker wall. Inner layer: white EPDM rubber. Reinforcement: polyester braid. Outer layer: red or blue micro-perforated EPDM rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +100°C.

Strong pressure hose designed for the transmission of water or compressed air in irrigation systems, agriculture, mines, construction sites, etc. The inner layer is smooth, ensuring minimal flow loss. The outer layer is slightly longitudinally ribbed, which increases abrasion resistance and protects against contact with hot elements. Resistant to abrasion, ozone, weather conditions, oil, fuels, and a wide range of chemicals. Lighter and more flexible than standard rubber hoses. Flat when at rest, facilitating handling and storage. Does not require washing and drying. Resistant to longitudinal loads – during unwinding and pulling (longitudinal force should never exceed 1/3 of the specified breaking force, installation of fittings should consider longitudinal force). Use for air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose. Hose material: black NBR/PVC blend embedded in a polyester-polyamide braid during the hose extrusion process. Working pressure: from 10 bar to 25 bar (water), from 7 bar to 18 bar (air) - depending on the hose diameter. Operating temperature for water: from -20°C to +80°C, temporarily up to +100°C.

Exceptionally flexible hose designed for compressed air. Due to features such as: lightweight, flexibility at low temperatures, resistance to elongation, it is particularly recommended for pneumatic tools, compressors, hose reels, etc. Inner layer: black PVC. Reinforcement: polyester braid. Outer layer: blue PVC. Working pressure: 15 bar. Operating temperature: from -20°C to +60°C.

Hose with steel spiral reinforcement, intended for hot water mixed with antifreeze fluids. Used in cooling and heating systems, for pumps in engines and machines. It has vacuum resistance. Inner layer resistant to heat and cooling fluids. Outer layer resistant to heat and aging. Rubber mixture compliant with DIN 73411:79 standard. Inner layer: black EPDM rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black EPDM rubber. Working pressure: 4 bar. Operating temperature: from -40°C to +120°C.

Very lightweight economical hose, flat in a resting state, designed for water transmission. An economical solution for low working pressures and non-demanding working conditions. Used in agriculture, e.g., for irrigation of crops, construction, and other industrial sectors. Hose material: blue PVC. Reinforcement: polyester layer. Working pressure: 3 bar. Operating temperature: from -5°C to +60°C.

Hose designed for the transmission of compressed air, for compressors, hammers, drills, and other pneumatic tools. Due to its low weight, flexibility, robust construction, and high working pressure, it has been accepted and successfully used for many years in construction (particularly in demolition companies), industry, and mining. Extremely durable and long-lasting due to high-quality materials and construction. Reinforced with a circumferentially woven polyester braid completely bonded and surrounded by rubber in the original hot extrusion process of the rubber mixture through the braid. UV resistant. The inner layer is smooth, ensuring minimal flow loss. The yellow, ribbed outer surface is resistant to abrasion, oils, and ozone, and is highly visible on construction sites. Flat when at rest, facilitating handling and storage. Resistant to longitudinal loads. Most commonly used with air couplings (spacing 42 or 41 mm) mounted with cast iron clamps (ordered separately). Also available in black. Use for high-pressure air should always be preceded by a risk analysis in the event of accidental disconnection or rupture of the hose and potential application of safeguards. Maximum working pressure established according to a safety factor of 4:1 approved by the manufacturer for air. Exceeding 1/3 of the specified breaking force is not recommended. Standard roll length: 200 m. Hose material: yellow NBR/PVC mixture with UV-resistant barrier, embedded in the polyester braid during the hose extrusion process. Working pressure: from 12.5 bar to 25 bar - depending on the hose diameter and temperature. Operating temperature: from -30°C to +75°C (temporarily up to +80°C).

Vacuum-resistant suction and discharge hose designed for cooling water in foundries, smelters, and all applications where rubber hoses operate close to a heat source. Glass fiber covering resistant to temperatures up to +530°C caused by thermal radiation. Used in cooling systems. Particularly recommended for water installations near metallurgical furnaces. Resistant to short-term exposure to splashes of molten hot metal. Standard length: 60 m or 120 m. Inner layer: black SBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: EPDM rubber / glass fiber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -40°C to +70°C, external up to +530°C.

Externally corrugated flexible and strong suction and discharge hose for water and sewage. It is characterized by good resistance to external damage and harsh operating conditions, as well as resistance to UV radiation and low temperatures. Used in irrigation systems, tankers, for flushing sewers, and emptying septic tanks. Also used in industrial installations. Hose material: gray-purple PVC. Reinforcement: hard PVC spiral. Working pressure: from 3 bar to 8 bar, depending on the hose diameter and temperature. Operating temperature: from -20°C to +50°C.

Flexible suction hose designed for sewage and water. Corrugated on the outside, nearly smooth on the inside. The special profile makes the hose resistant to vacuum and kinking (it returns to its shape). As a polyethylene hose, it has very good chemical resistance and resistance to biological corrosion (rotting, decay). It remains flexible at low temperatures. The hose is commonly used for emptying septic tanks and portable toilets, in construction, tourist facilities, marinas, and airports. Hose material: yellow polyethylene profile (PE). Reinforcement: black polyethylene profile (PE). Vacuum: 0.95 bar (for diameter 51mm ÷ 76mm); 0.85 bar (for diameter 102mm). Operating temperature: from -40°C to +60°C.

Durable pressure hose designed for the transport of industrial water, sewage, sludges, etc. Inner layer: black smooth SBR rubber. Reinforcement: high-strength synthetic cord. Outer layer: black SBR rubber. Working pressure: 10 bar. Operating temperature: from -30°C to +70°C.

Very lightweight and flexible flat-folded suction hose for water for fire pumps, without fittings. Used for fire, rescue, and forestry pumps. In addition to fire-fighting functions, widely used for water transfer in industry, construction, agriculture, and mining. The inner layer is smooth, resistant to mold and rot. The outer layer (braid) has high strength, with a polyurethane coating that does not retain dirt, increasing resistance to abrasion and contact with flames. Certifications: hoses compliant with the technical conditions of the MSWiA Regulation of April 27, 2010. Inner layer: smooth polyurethane. Reinforcement: polyester braid. Outer layer: red polyurethane coating. Working pressure: from 12 bar to 15 bar - depending on the hose diameter. Operating temperature: from -30°C to +70°C.

Flexible hose designed for compressed air. Recommended for pneumatic tools, compressors, hose reels, etc. Inner layer: black PVC. Reinforcement: polyester braid. Outer layer: beige PVC. Working pressure: 20 bar. Operating temperature: from -15°C to +60°C.