Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsPush-on coupling with female thread, type C2, designed for connecting hoses made of soft plastics. The connection is made by pushing the hose onto the fitting and clamping it by tightening the nut. Material: nickel-plated brass. Working pressure: 18 bar.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling push-in straight of couplings push-in for hose o diameter metric, series S, type PUCM. economical solution for connecting flexible hoses pneumatic o metric calibrated diameter outer. easy and fast in use. Material: plastic plastic. Working pressure: 10 bar. Vacuum: 0.99 bar. Operating temperature: od 0°C up to +60°C. sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBalancer without automatic lock designed is for relief tools hand, power tools etc. in order to improvement comfort use. through load capacity spring offset weight suspended tools, improving safety and ergonomics. load capacity spring adjustable is using a knob is found on body. should adjust load capacity balancer for mass suspended tools. Material housing: aluminum cast. Material cable: steel stainless. length cable: 1600 mm. thickness cable: 2 mm. Operating temperature: up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA coil 22 mm for valves PIV.I, stem Ø8. Insulation class: F155. Voltage tolerance: -10% for +10%. Protection degree: IP65 EN60529 with a connector. Compliant with ATEX 94/9 CE, group II, category 3GD.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe HPA screw-together socket of a hydraulic quick coupling, intended for installations at very high pressures with large mechanical loads. Used in hydraulic presses, rescue equipment, hydraulic lifts, cutters, etc. It can be connected / disconnected when residual pressure is present in the system. Caps should be ordered separately. Material: carbon steel. Sealing: NBR. Flow: 1/4" - 16.4 l/min; (Δp=4 bar), 3/8" - 21.3 l/min; (Δp = 4 bar). Working pressure: 700 bar. Burst pressure: 1/4" - 2100 bar (coupling connected), 3/8" - 1850 bar (coupling connected), 1/4" - 1800 bar (socket disconnected), 3/8" - 1850 bar (socket disconnected). Operating temperature: from -25°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket quick coupling NiTO SC, with protection against disconnection, with fitting for hose. For use with hot water (above +60°C) in those installation locations where they are used directly by the operator and frequently disconnected. Material: brass chrome-plated. Working pressure: up to 25 bar. Operating temperature: up to +150°C. Sealing: Viton.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket quick coupling Hansen Beverage with valve and gasket with a thread external UNF 11/16″-18. The couplings are available in two versions: for gases type 2HG and for liquids type 2HL. These versions are not interchangeable with each other (different plug diameter), which allows avoiding mistakes in connection. Recognizing the version is very easy. For gas couplings, the identification ring on the socket is white, and the hexagon on the plug has a notch. For liquid couplings, the identification ring on the socket is black, and the hexagon on the plug has no notch. pressure working: 15 bar. Operating temperature: up to +130°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket coupling CAMLOCK C with a serrated hose fitting made in accordance with the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer coupling, especially in the petrochemical industry. Working pressure: up to 10 bar, depending on the coupling size. Material: aluminum. Levers: steel AISI 304 (in sizes 1.1/4" for 4" - Levers made of brass). Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSafety clip is used to securing the connected coupling (plug with socket SKV) during maneuvering or carrying lines connected przed ich disconnecting. Diameter D - outer diameter. Material: steel galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting banjo intended for installation using soldering on metric tubes made of carbon steel. Fitting has hole D matched for diameter external tubes. Version with a hole banjo F matched for bolts with inch thread. Material fittings: carbon steel raw (without galvanizing). To select material lutowniczego and techniki soldering please contact Tubes International.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose fitting with a BSP male thread for use in industrial installations, e.g. for air. Material: brass. Working pressure: up to 12 bar. Operating temperature: from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting flange 90° INTERLOCK SAE 6000, O-ring or other gasket in the flange groove, for hose type 4SH, R13 and R15. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting flange straight NON SKIVE SAE 6000 (SFS), series heavy, intended for crimping onto hoses type 4SP, 4SH, R13 and R15 using a ferrule TI-N.... Assembly: without skiving gumy hose. Material: carbon steel, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting type SA with a BSP male thread, 60° cone seal, intended for low-pressure rubber and plastic hoses, unreinforced and with textile reinforcement, with an external steel braid. Commonly used in flexible lines for sanitary fittings, fuel and air installations, etc. Material: brass.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting type CNP terminated with a tapered BSPT male thread made of AISI 316 steel with a "tail" for a hose. Intended for rubber hoses and industrial plastic hoses. Assembly by means of bands, clamps or special sheet-metal ferrules of the CNFL type. Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsClosing screw with BSP male thread, type A7, with a hex socket head. Material: nickel-plated brass. Working pressure: 60 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpigot with a thread external for the SPEEDFIT system, used in compressed-air installations. The installation can be made using plastic or metal pipes (copper, brass, aluminum). By pushing the spigot into the coupling, we obtain the possibility of connecting to the installation with a female thread. Material: plastic plastic. pressure working: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMini actuator double-acting operation ISO 6432 STD, type 112 with magnet, without cushioning. It has been designed to work with filtered air, oiled or non-oiled, and does not require additional maintenance operations. A stainless steel sleeve was used to make the actuator. The dimensions of the external covers of some diameters have been reduced, which allows mounting the actuators in difficult and confined spaces. The service life of actuators with NBR seals is 15 million cycles, with polyurethane ones 30 million cycles. The presented values should not be treated as binding or guaranteed, but only as a reference due to the variability of many factors, including loads radial and axial, speed, temperature, czy losses air (values limit). Piston diameter: Ø 8, 10, 12, 16, 20 and 25 mm. stroke working: od 5 for 500 mm. pressure working: od 0.8 up to 10 bar (Ø 8, 10, 12 mm); od 0.6 up to 10 bar (Ø 16, 20, 25 mm). Sealing: polyurethane, NBR, FKM/FPM. Operating temperature: from -10°C to +150°C depending on used seal.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA socket with a thread NPT, BSPT, BSP and A socket reducing with a thread NPT, for pipe connections intended mainly for industry chemical, petrochemical, pharmaceutical, power generation, nuclear power plants and process engineering. Material: steel AISI 316.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA nut with a metric thread intended for mounting a DIN 3015 standard clamp type 100/101 and a DIN 3015 double clamp type 201 on an ABINS rail. Material: alloy zinc with aluminum.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA nut railway HEAVY DUTY with gasket, with a thread metric, pod wrench hook. Material: aluminum. Sealing: NBR. pressure working: 6 bar. Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReducing nipple made of stainless steel, type 62020, with BSPT male thread. Material: AISI 316L steel. Operating temperature: from -20°C to +225°C. Working pressure: 140 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBand clamp with a worm-drive lock, equipped with a spring to compensate for dimensional changes in the connection (hose shrinkage due to cold flow of the material or due to large temperature changes). The spring is a set of 10 disc (Belleville) springs – washers under the screw head. This maintains the clamp's grip and sealing around the entire circumference of the hose, preventing leakage from the installation. The clamp's spring mechanism automatically increases or decreases its diameter while maintaining the clamp's grip. Particularly recommended in the case of large temperature changes for heavier applications. Correct clamping is indicated by the screw end protruding beyond the lock housing and by the flattened disc springs. The clamp's inner insert protects the hose surface from damage. Installation tightening torque 8.5 Nm (max. 14.1 Nm). Screw/lock material: stainless steel 410. Band material: stainless steel 300. Band width: 16 mm (5/8").
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCover SAFE SLEEVE with dense fabric intended for protection hoses or bundles lines hydraulic and pneumatic. Excellent abrasion resistance (tested according to SFS-EN ISO 12947-3), chemically resistant and UV-resistant, low electrical conductivity. The cover protects people in the vicinity of a bursting hose. Meets the EN ISO 3457 and EN 12999 standards. The tape width attribute specifies the width of the cover in the flat state. Material: black polypropylene (without printing). Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong fabric glass coated on both sides rust silicone, o basis weight 1085 g/m 2. used primarily as cover welding, a also in applications na outside and in industry offshore, of regard na resistance na moisture and light solar. Material: fabric glass coated silicone. Operating temperature: from -54°C to +260°C (momentarily up to +1185°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA blade spare for shears PZG28 (ZC-PZG28).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe high-pressure SG28 water gun for industrial applications. The outlet part is terminated with a female 1/4" BSP thread. The gun is also available with a swivel connection to the installation. Housing material: high-strength plastic. Working pressure: up to 250 bar. pressure The permissible: 280 bar. Flow rate: 30 l/min. Operating temperature: up to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA universal gun for air, water and also non-explosive liquids. Intended mainly for blowing out contamination, also in hard-to-reach places. It is characterized by a strong blowing force, with the possibility of adjusting the flow rate. Lightweight construction, ergonomic gun shape and low trigger press force ensure great working comfort. As standard, the gun is equipped with a socket with a 1/4" BSP or 1/4" NPT thread. this model Available is in version with nozzle 90 mm bent, which nie is replaceable. Material: POM (body), brass (valve) Sealing: NBR. pressure working: 16 bar. pressure bursting: 64 bar. Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAn AKBO HEAVY DUTY water gun, Equipped with a beam adjustment screw. It is not intended for steam. Body material: brass. Pusher material: stainless steel. The trigger tongue, handle and gun body are rubber-coated (EPDM), providing better insulation. Connection: 1/2" BSP female. Working pressure: 24 bar. Flow rate: 75 l/min. Operating temperature: up to +95°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCrimping press P20 HP with manual drive pump hydraulic, works everywhere tam, where not has access for stream ani compressed air, a compact The design and small weight allows on performing repairs in space failure. has mechanical indicator (pins control) reaching diameter crimp and possibility settings the head in two positions (rotation o 90⁰). Intended for workshops repair, points service, vehicles technical. All FINN-POWER crimping presses are adapted to work with interchangeable jaw sets (ordered separately). On example for range diameters crimp od 10 for 61 mm should order 12 sets jaws standard od FP-20-10 for FP-20-54.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReady, flexible, four-braid line high-pressure, used mainly for tensioning bolts, cutting water, for lifts, wrenches and other equipment hydraulic. line is tested pressure and supplied of appropriate certificate. meets standard EN 1829-2. Inner layer: POM (polyoxymethylene). Reinforcement: four braids with highly strength wire steel. Outer layer: PA (polyamide). Material fittings and ferrule: steel carbon, galvanized. Working pressure: up to 1800 bar. Operating temperature: od -30°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details"T" tee connector with a BSPT female thread type AI 13240 intended for joining copper, brass, steel, aluminum, etc. pipes as well as plastic pipes and hoses (e.g. polyamide). Range of external diameters of the joined pipes from 4 to 18 mm. The tightness of the connection is achieved by clamping the ring onto the joined pipe and simultaneously pressing the pipe with the ring into the socket by means of a nut. Standard: EN 1254-2. Material: brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble BANJO bolt with washer, type D8, for type R13, R14, D12, D17, D5, D6 fittings. Material: nickel-plated brass. Working pressure: 18 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUnion with a thread internal BSP and a BSPT male thread intended for use in pipe connections of industrial installations. sealing union cone (metal- metal). Material: steel AISI 316. Working pressure: 10 bar. The given dimensions are indicative and may differ slightly depending on the manufacturer.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTee plug-in "T" through-flow, type R5, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA profile gasket for a TW (tankwagen) coupling, type GSD (for a 4" coupling, an O-ring gasket type TWO is used). Material: Viton (FPM). Temperature range (approximate): from -20°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThick, strong hose intended for lances oxygen in industry metallurgical. Layer outer self-extinguishing made in accordance with the standard ASTM C 542. Inner layer: black rubber CR. Reinforcement: double cord textile, spacer with fibre glass. Outer layer: yellow or blue rubber CR. Working pressure: 30 bar. Operating temperature: od -30°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose with flexible PVC reinforced double a braid polyester intended for washing under medium pressure cold and warm water and light chemicals in industry food. is characterized exceptional resistance on temperature - for +70° at pressure working 40 bar. compliant with the European requirements for substances food 1935/2004 CE and 2007/19/CE (simulant fluids A, B, C). use fittings crimped for hoses THERMOCLEAN. Inner layer: grey, smooth PVC. Reinforcement: double cord polyester. Outer layer: blue PVC. Working pressure: 80 bar. Operating temperature: od -10°C up to +70°C (momentarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMedium wall thickness, flexible hose intended for discharge dusts, sawdust, chips, offcuts, light bulk materials etc. Specially designed according to the requirements of the wood and furniture industry, it can also be used in other industries. compliant with the standard DIN 26057 Type 2. Antistatic and flame-retardant, it ensures a high level of work safety. less pliable and compressible than SMARTFLEX® 0.4 and 0.6, za to smooth inside, flexible also in low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticisers. Resistant to oils and petrol. The optimal flow direction of the medium is marked with an arrow. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. Anti-electrostatic properties: permanently antistatic (in accordance with ISO 8031 resistance R 9 Ω, in accordance with the German technical regulations TRGS 727 (6.4.2.4) specific resistance R 8 Ωm, in accordance with directive 2014/34/EU (ATEX) it can be used in specified explosion-hazard zones - which should be preceded by a risk analysis). After effective two-sided earthing of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – in accordance with DIN 4102 class B1. Hose material: transparent polyether-polyurethane. Wall thickness measured between the spiral: 0.7 mm. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose suction - delivery intended for conveying substances food, requiring the use of rubber free of odour and taste. Contains no phthalates or bisphenol A. thanks to reinforcement spiral steel, has good resistance to vacuum. Suitable for milk and dairy products, as well as wine, beer, fruit juices. not recommended for oils and greasy substances food. Widely used in industry food. Layer outer hose resistant to abrasion and conditions atmospheric. Standards and requirements: Food industry, food contact: 1935/2004/EC and 2023/2006/EC (GMP). D.M. 21/03/73, FDA 21 CFR 177.2600, BfR XXI kat. 2. Inner layer: white rubber natural (NR). Reinforcement: cord synthetic, steel spiral. Outer layer: blue EPDM rubber. Working pressure: 6 bar. Operating temperature: from -25°C to +80°C.
