Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsA connection block (adapter) intended for connecting hydraulic lines to plate valves (directional valves). Fitted with NG6 plate connections and threaded connections: to the pump (P) - 1/2" BSP female, to the tank (T) - 1/2" BSP female, to the receiver (A and B) - 3/8" BSP female and pressure-gauge (G) - 1/4" BSP female. Material: steel. Maximum working pressure: 315 bar. Flow: 40 l/min. Operating temperature: od -20°C up to +80°C (medium), od -20°C up to +50°C (ambient).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle extended bent o diameter hole 3 mm for guns for air, terminated a thread metric M12x1.25. diameter tubes: 5 mm. Available length: 110 mm, 160 mm and 260 mm. Material: brass nickel-plated. Maximum pressure: 10 bar. Operating temperature: from -10°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFilter with reducer (filter-regulator) series SYNTESI®, with end connections 1/8", 1/4", 3/8", 1/2", 3/4", 1", is a device consisting of a filter and a reducing valve. It is built from the same components as the filter and reducer, so it has the same technical characteristics. It reduces and purifies the air supplied by the compressor. Size: SY1, SY2. Output pressure range: 0÷8, 0÷12 bar. Supply pressure: up to 15 bar for SY1 and up to 13 bar for SY2. Operating temperature: od -10°C up to +50°C. Connection: 1/8" BSP female ÷ 3/8" for SY1 and 3/8" BSP female ÷ 1" for SY2. Additional connection for a pressure gauge or fittings: 1/8" BSP female for SY1 and 1/4" for SY2. Condensate drain: manual / semi-automatic (RMSA), automatic (RA). Flow rate: 1300 l/min - 1/8", 2000 l/min - 1/4", 3000 l/min - 3/8" (SY1), 5800 l/min - 3/8" (SY2), 7200 l/min - 1/2", 7400 l/min - 3/4", 1" (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSocket water quick coupling NiTO CLICK 3/4" with fitting for hose. NiTO CLICK quick couplings are water quick couplings made to the profile of very popular plastic garden quick couplings and compatible with them. Sealing by means of an O-ring placed externally on the plug. Manufactured in Denmark – 5-year warranty. They retain the simplicity of the commonly known plastic quick couplings and are characterized by strength and durability. Intended for water, water with cleaning agents, for use in industry, services, horticulture, agriculture, etc.. Material: brass chrome-plated (matte - satin). Working pressure: up to 25 bar. Operating temperature: from -30°C to +80°C. Sealing: NBR (not suitable for gasolines and oils).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA 90° PUSH-ON end with a female BSP thread, type YBW210, intended for a special self-clamping hose designed for this type of end. Mounted onto the hose without the use of clamps or brackets. It has a special barb profile adapted to the material and dimensions of the PUSH-ON hose and the construction of its braid, causing the hose to clamp onto the barbs of the end. The end must not be used with other hoses or clamped with clamps or brackets, as this risks damaging the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specification of the PUSH-ON hose. Material: galvanised carbon steel, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA clamp RUBBER P-CLIP compliant with the standard DIN 3016 recommended for safe and damping vibrations mounting pipes, hoses, bundles cables, corrugated pipes electrical-installation (cover on cables) etc., for which exists possibility abrasion and damage. A clamp this type found wide use, m.in.: machine agricultural and construction, design engines combustion, industry railway, equipment electric, equipment AGD etc. made is with one section bent tape steel and rubber flange. holes on obu ends tape are reinforced steel plates, co ensures strength on clamping at large loads mechanical. tape made of carbon steel galvanized (W1), profile with rubber EPDM resistant to water, abrasion, changes temperatures and aging. A clamp not contains screws, washer and a nut. Material: steel carbon, galvanized (tape), EPDM rubber (flange). Band width: 15 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA LET-LOK® straight fitting with a thread external NPT for an inch tube intended mainly for the chemical, petrochemical and pharmaceutical industry, power generation, nuclear power plants and process engineering. The permissible working pressure is determined on the basis of the outer diameter and the wall thickness of the tube (details in the attachment). Available in a full-bore version - often used for mounting a thermocouple, has a bore diameter reamed to the tube diameter (marked...-TC at the end of the index code). Material: steel AISI 316.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDirectional valve plug-in adjustable, type R43, intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: plastic plastic. Working pressure: 12 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +60°C. sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrew-together ferrule for hoses termoplastycznych type MT1 or MTH1. Use only with fittings screw-together from the same supplier (TI-S...). Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery for sandblasting extremely resistant to abrasion. thick Layer inner with rubber o exceptionally sound resistance to abrasion (36 mm 3 acc. to ISO 4649:2014). exceeds requirements standards ISO 3861:2008. The electrically conductive inner layer and antistatic outer layer prevent the accumulation of electric charges. Used for strongly abrasive materials such as quartz sand, steel shot, corundum, glass in abrasive blast treatment of steel structures, castings, concrete surfaces, etc.. Mounted with special sandblasting ends. Inner layer: black rubber NR/BR/SBR. Reinforcement: cord synthetic. Outer layer: black rubber SBR. Working pressure: 12 bar. Operating temperature: od -35°C up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible hose for water adapted for winding on drums. intended for use in high-pressure equipment firefighting and in vehicles fire ( booster hose ). Layer inner resistant to agents firefighting and foam-forming. Reinforcement made with thick layer high-strength cord. Layer outer resistant to conditions atmospheric. hose CHICAGO EN varies od basic version hose CHICAGO, made compliant with with the standard EN 1947: 2014 ( type C, class 1, category 2 ), whereas CHICAGO EN GL, made compliant with with the standard EN 1947, ale with luminescent layer external, enabling easy perceiving hose in darkness or at smoke. On special order available also versions hose compliant with the standard: ASTM C-542 and BS 3169. length standard roll: 60 m (120 m po confirmation for basic version hose). Inner layer: black EPDM rubber. Reinforcement: cord synthetic. Outer layer: black EPDM rubber (yellowish luminescent synthetic rubber – version GL). Working pressure: 40 bar. Operating temperature: od -40°C up to +100°C, od -20°C up to +60°C (EN 1947).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery Light, flexible and very pliable hose intended for discharge aggressive chemical vapours and gases we all fields industry. excellent resistance chemical, high resistance temperature. hose is characterized high compressibility, resistance on impacts thanks to outer spiral. resistant to radiation UV, ozone, aging, conditions atmospheric, flame-retardant. available other diameter in the scope 50 ÷ 508 mm and version of spiral of steel stainless. Assembly of the hose on connectors with bridge clamps (lewo-handed). version PTFE EL CL - hose conductive electrically o resistance R ≤10 6 Ω, compliant with the directive ATEX 94/9/EC and the standard TRBS 2153, made with black PTFE. Checking chemical resistance - the chemical resistance table for PTFE (preliminary selection), confirmation of resistance and conditions of use - by Tubes International. length standard: 3 or 6 m. Hose material: light-brown fabric glass coated Teflon (PTFE), o wall thickness 0.12 mm - version standard PTFE CL, fabric glass coated black conductive Teflon (PTFE), o wall thickness 0.15 mm - version antistatic PTFE EL CL. Reinforcement: outer spiral with wire and sheet steel galvanized. Operating temperature: od -150°C up to +250°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for oil hydraulic systems, fuels, water-based fluids. For use in the vicinity of transformers and medium- and high-voltage electrical installations. Non-conductive - leakage under the standard's test conditions lower than 50 µA for a voltage of 246 kV/m over 5 min. standards: DIN 24951, SAE 100R7, ISO 3949-R7. Inner layer: polyester. Reinforcement: a double polyester braid. Outer layer: orange polyurethane. Working pressure: from 157 bar to 220 bar, depending on the hose diameter. Operating temperature: from -40°C to +93°C (for water up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug cap coupling CAMLOCK DC made in accordance with the American military standard MIL-C-27487 (A-A-59326). Working pressure: up to 10 bar, depending on the coupling size. Material: brass. Levers: steel AISI 304. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve directional electric, without a coil control PIV for mounting wired. is to element pneumatics, which task is Control direction flow the medium working in pneumatic systems drive and control through connection or switching ways flow. appropriate for use with high frequency and short sometimes response. possible Mounting in any position. Material body valve: aluminum. thread connection: M5 female, female BSP1/8”. medium working: filtered compressed air, oiled or nie oiled. Maximum pressure working: from 6 bar to 30 bar, depending on type valve and a coil. Operating temperature: -15°C up to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA STORZ adapter with a female BSP thread intended for transfer installations for liquid and bulk substances. Used in firefighting, irrigation systems, the chemical and food industry, agriculture, etc.. Characterized by a large, unobstructed flow diameter. With a symmetrical design of the connection part, thanks to which they can be easily connected together. Parts with the same lug spacing can be connected. Material: brass. Working pressure: 16 bar. Gasket: black NBR rubber.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter - tee high-pressure type A117 with BSP female thread, with a swivel nut (60° cone sealing). Material: AISI 316L.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNozzle standard bent, for installations directly for the body the gun. length nozzle: 90 mm. pressure working: 16 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRing handle for coupling CAMLOCK, type R. Material: steel AISI 304.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsComplete coupling push-in angled BANJO, type R54, Intended for connections lines and other element in systems pneumatic. easy and fast in use for repeated mounting without loss tightness po side mechanical and pneumatic. Material: brass nickel-plated. Working pressure: 16 bar. medium working: vacuum, air. Operating temperature: od -20°C up to +80°C. sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting hydraulic screw-together, type S, with metric male thread, 24° cone sealing (CEL), series light. intended for screwing onto hoses rubber and termoplastycznych using a ferrule screw-together. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA 45° PUSH-ON end with a female BSP thread, type YBW310, intended for a self-clamping hose designed for this type of end. Mounted onto the hose without the use of clamps or brackets. It has a special barb profile adapted to the material and dimensions of the PUSH-ON hose and the construction of its braid, causing the hose to clamp onto the barbs of the end. The end must not be used with other hoses or clamped with clamps or brackets, as this risks damaging the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specification of the PUSH-ON hose Material: galvanised carbon steel, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA sealing O-ring for a NiTO quick coupling. Material: EPDM. Operating temperature: up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA clamp RUBBER P-CLIP compliant with the standard DIN 3016 recommended for safe and damping vibrations mounting pipes, hoses, bundles cables, corrugated pipes electrical-installation (cover on cables) etc., for which exists possibility abrasion and damage. A clamp this type found wide use, m.in.: machine agricultural and construction, design engines combustion, industry railway, equipment electric, equipment AGD etc. made is with one section bent tape steel and rubber flange. holes on obu ends tape are reinforced steel plates, co ensures strength on clamping at large loads mechanical. tape made of steel stainless AISI 304 (W4), profile with rubber EPDM resistant to water, abrasion, changes temperatures and aging. version W4 recommended for applications in industry marine. A clamp not contains screws, washer and a nut. Material: steel AISI 304 (tape), EPDM rubber (flange). Band width: 20 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting 90° type LET-LOK® with a thread external NPT for a metric tube intended mainly for the chemical, petrochemical and pharmaceutical industry, power generation, nuclear power plants and process engineering. The permissible Working pressure fittings is determined on the basis of a given size and type connections threaded (details in the attachment). Material: steel AISI 316.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting angled 90° adjustable JIC 37° with BSPT male thread (sealing on the thread – PTFE tape or anaerobic sealant). Material: carbon steel, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for coolant in system 3/4" made with resistant to corrosion, solvents, oils and greases acetal, ensuring rigidity and resilient lines. intended for low-pressure conveying air, water, oils and other substances used in processes cooling and treatment metals. resistant to abrasion and vibration, ensures 100% stability position and not causes damage tools cutting. very easy in expansion modular The design. available length: 2x145 mm, 100 mm, 200 mm, 300 mm, 400 mm, 500 mm, 600 mm, 700 mm, 800 mm 900 mm and 1000 mm. Material: acetal. Working pressure: for 1.4 bar. maximum Flow rate: 5182 l/h. Operating temperature: up to +76°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose suction intended for conveying dry or liquid substances abrasive, granulates etc. externally Serrated, inside smooth. Layer inner with transparent, resistant to abrasion polyurethane. The hose has a copper wire arranged along the spiral which, after earthing or connection to an end, discharges electric charges. Widely used in processing plastics in use demanding greater resistance to abrasion, puncturing and cutting hose. especially recommended for regrind plastics o relatively sharp edges. Inner layer: transparent polyurethane. Reinforcement: rigid-PVC spiral. Hose material: transparent PVC. Working pressure: from 3 bar to 7 bar - depending on the diameter hose and temperatures. Vacuum: from 0.69 bar to 0.74 bar - depending on the diameter hose and temperatures. Operating temperature: od -5°C up to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very flexible and pliable, resistant chemical and temperature-wise two-layer hose intended for discharge most aggressive chemical vapours, gases, dusts and fibres (non-abrasive), air blowing hot air. very good resistance chemical on aggressive chemicals thanks to internal layer PTFE. W version standard inner Layer white natural PTFE meets requirements industry food (FDA). W version antistatic EL black inner Layer PTFE is electrically conductive (R ≤10 6 Ω). thanks to layer outer with fabric glass coated silicone and layer internal with PTFE hose is resistant to temperature for 250ºC. hose is characterized high compressibility - for 1:6, strong design resistant on vibration, stretching and tearing, resistance on impacts thanks to outer spiral. resistant to radiation UV, ozone, aging, conditions atmospheric, flame-retardant. used in industry chemical, metallurgy metals and foundry, industry ceramic and glass. Also available with a stainless steel spiral (from 80 mm diameter). Assembly of the hose on connectors with bridge clamps (lewo-handed). Checking chemical resistance - the chemical resistance table for PTFE (preliminary selection), confirmation of resistance and conditions of use - by Tubes International. length standard: od 2 for 10 m. Material hose Inner layer: white foil PTFE PTFE - version standard SILTEF, black conductive foil PTFE PTFE - version antistatic SITEF EL. Material hose Outer layer: fabric glass coated silicone, silver - grey. Reinforcement: outer spiral with wire and sheet steel galvanized. Operating temperature: od -50°C up to +250°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible hose intended for oil hydraulic systems, gases, air, fuels, water-based fluids. Inner layer: polyester. Reinforcement: a polyester braid. Outer layer: micro-perforated polyurethane. Working pressure: from 110 bar to 130 bar, depending on the hose diameter. Operating temperature: from -40°C to +93°C (for water and air up to +65°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve throttle check type MRF OFC series COMPACT "O" for direct mounting in connections the actuator, used in systems pneumatic for adjustment rate flowing stream compressed air and direction flow. equipped in coupling with a thread internal. Setting adjustment using a screwdriver, with the possibility of mounting a protective cover. Size: M5, 1/8″, 1/4″, 3/8″, 1/2″. pressure working: up to 10 bar. Operating temperature: from -10°C to +70°C. Material: brass nickel-plated.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsValve reducing REG, series SYNTESI®, without end connections, serves for regulation pressure working and ensures correct operation, in connected za nim installation, independently od changing sie wear medium. W a valve used instead of diaphragm flat diaphragm shaped, which ensures greater value flow nominal thanks to greater surge diaphragm, greater sensitivity and speed reaction on change setting, thanks to reduction friction static and kinetic components and greater accuracy in maintaining set pressure output at change value flow and pressure supply. W case rise pressure output over value setting diaphragm opens valve trigger and vents reducer until for obtaining value pressure compliant with setting. mechanism type „push-lock” allows on locking a knob in any position through its pressing. Plate locking allows mounting padlock protective against unauthorised change setting pressure output. additional the connection with the front and with the back of size 1/8” can be used for connection pressure gauge, relay pneumo-electric or fittings push-in. drawn with these connections air is reduced. Size: SY1, SY2. range pressure output: 0÷2, 0÷4, 0÷8, 0÷12 bar. Supply pressure: up to 15 bar for SY1 and up to 13 bar for SY2. Operating temperature: od -10°C up to +50°C. Connection: 1/8" BSP female ÷ 3/8" for SY1 and 3/8" BSP female ÷ 1" for SY2. Additional connection for a pressure gauge or fittings: 1/8" BSP female for SY1 and 1/4" for SY2. Flow rate: 1200 l/min - 1/8", 2800 l/min - 1/4", 3350 l/min - 3/8" (SY1), 5300 l/min - 3/8" (SY2), 7400 l/min - 1/2", 7600 l/min - 3/4", 1" (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA STORZ coupling with a hose end intended for transfer installations for liquid and bulk substances. Used in firefighting, irrigation systems, the chemical and food industry, agriculture, etc.. Characterized by a large, unobstructed flow diameter. With a symmetrical design of the connection part, thanks to which they can be easily connected together. Parts with the same lug spacing can be connected. Available in a forged version with a working pressure of up to 16 bar and in a cast version, characterized by a significantly lower strength, with a working pressure of up to 6 bar. Material: aluminum. Working pressure: 16 bar (coupling forged), 6 bar (coupling cast). Gasket: white NBR rubber (forged couplings), black NBR rubber (cast couplings).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdapter - tee high-pressure type A111 with female thread 3 x BSP (thread sealing). Material: AISI 316L.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA PUSH-ON end with a male BSP thread, type YBZ110, intended for a self-clamping hose designed for this type of end. Mounted onto the hose without the use of clamps or brackets. It has a special barb profile adapted to the material and dimensions of the PUSH-ON hose and the construction of its braid, causing the hose to clamp onto the barbs of the end. The end must not be used with other hoses or clamped with clamps or brackets, as this risks damaging the hose. Operating temperature: from -40°C to +80°C. Working pressure in accordance with the specification of the PUSH-ON hose. Material: galvanised carbon steel, brass, AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug JIC 37° with UNF male thread (sealing on the external 37° cone). Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight connector with a female thread allowing UHP quick couplings and hoses to be joined together. Material: carbon steel, black-galvanized. Working pressure: 700 bar (at a safety factor of 4), 1000 bar (at a safety factor of 2.8).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA clamp RUBBER P-CLIP compliant with the standard DIN 3016 recommended for safe and damping vibrations mounting pipes, hoses, bundles cables, corrugated pipes electrical-installation (cover on cables) etc., for which exists possibility abrasion and damage. A clamp this type found wide use, m.in.: machine agricultural and construction, design engines combustion, industry railway, equipment electric, equipment AGD etc. made is with one section bent tape steel and rubber flange. holes on obu ends tape are reinforced steel plates, co ensures strength on clamping at large loads mechanical. tape made of steel stainless AISI 304 (W4), profile with rubber EPDM resistant to water, abrasion, changes temperatures and aging. version W4 recommended for applications in industry marine. A clamp not contains screws, washer and a nut. Material: steel AISI 304 (tape), EPDM rubber (flange). Band width: 12 mm.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHandy Feather for compressed air, intended for fast removing with surfaces all contamination: liquids, fine chips, filings itp. made with anodized aluminum. equipped in nozzle with the possibility regulating flow one hand - od narrow for wide stream air. rubber a nozzle na the tip feather protects surfaces against scratching. terminated a plug EUROSTANDARD 7.2. Material: housing – aluminum protected method anodized; sealing – NBR. diameter hole nozzle: 0 ÷ 3 mm. flow nominal: 300 l/min at a pressure of 6 bar. pressure Maximum: 12 bar. pressure operating: 1 ÷ 6 bar. Operating temperature: from -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA LET-LOK® straight fitting with a thread external BSP for an inch tube intended mainly for the chemical, petrochemical and pharmaceutical industry, power generation, nuclear power plants and process engineering. The permissible working pressure is determined on the basis of the outer diameter and the wall thickness of the tube (details in the attachment). Available in a full-bore version - often used for mounting a thermocouple, has a bore diameter reamed to the tube diameter (marked...-TC at the end of the index code). Material: steel AISI 316.
