Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose designed for pneumatic transport of dry abrasive substances. Inner layer made of white, smooth, abrasion-resistant rubber (≤110±5 mm³ according to ISO 4649, formerly DIN 53516), food-grade, phthalate-free, compliant with FDA 21 CFR 177.2600 for contact with dry food and BfR XXI category 4. Reinforcement with synthetic cord. Two built-in copper wires that, when grounded (or connected to a grounded end), dissipate electric charges. Outer layer made of electrically conductive rubber, resistant to weather conditions and ozone. Hose intended for the transport of dry food substances: grains, sugar, powders, feeds, granules, etc., as well as other abrasive substances such as PVC granulate, for which a white, non-staining inner layer is required. Not intended for use in ATEX explosion hazard zones. Available in two versions: BN standard (working pressure 6 bar) and BN SPECIAL (working pressure 8 bar). Standard length: 60 m (or 120 m - contact Tubes International). Standards and requirements: Food industry, contact with food 1935/2004/EC, 2023/2006/EC (GMP). Inner layer: white NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black EPDM rubber. Working pressure: 6 bar or 8 bar. Operating temperature: -30°C to +70°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for sandblasting, extremely resistant to abrasion. Thick inner layer made of rubber with exceptionally good abrasion resistance (40±5 mm³ according to ISO 4649 / DIN 53516). Exceeds the requirements of ISO 3861:2008 standard. The inner and outer layers are antistatic, preventing the accumulation of electric charges. Used for highly abrasive materials such as quartz sand, steel shot, corundum, glass in abrasive blasting of steel structures, castings, concrete surfaces, etc. Fitted with special nozzles for sandblasting. Standard length: 60 m / 40 m for a diameter of 16 mm (or 120 m - contact Tubes International). Inner layer: black NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 12 bar. Operating temperature: from -40°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for sandblasting, extremely resistant to abrasion. Thick inner layer made of rubber with exceptionally good abrasion resistance (36 mm³ according to ISO 4649:2014). Exceeds the requirements of ISO 3861:2008 standard. The inner layer is electrically conductive and the outer layer is antistatic, preventing the accumulation of electric charges. Used for highly abrasive materials such as quartz sand, steel shot, corundum, glass in abrasive jet processing of steel structures, castings, concrete surfaces, etc. Fitted with special nozzles for sandblasting. Inner layer: black NR/BR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black SBR rubber. Working pressure: 12 bar. Operating temperature: from -35°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSoft suction hose, for larger diameters and small thicknesses almost flat at rest, intended for pneumatic transport of dry bulk materials. Inner layer made of black, smooth, antistatic rubber (R < 106 Ω), abrasion-resistant (70±5 mm3 according to ISO 4649, formerly DIN 53516). Reinforcement with synthetic cord. Outer layer made of antistatic (R < 106 Ω) abrasion-resistant rubber, weather-resistant and ozone-resistant. The hose is primarily used for the transfer of cement, sand, gravel, silica, and other dry abrasive materials from rail tankers, road tankers, and silos. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black NR/SBR rubber. Working pressure: from 5 bar to 6 bar - depending on the hose diameter. Operating temperature: from -40°C to +70°C. Indices marked at the end with the letters XE have an inner layer made of high-abrasion-resistant antistatic rubber (abrasion 50 mm3 according to ISO4649) and with a copper wire.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for plastering. Inner layer made of rubber with good abrasion resistance (70±5 mm³ according to ISO 4649 / DIN 53516). Both inner and outer layers are antistatic to prevent the accumulation of electric charges. Multiple reinforcement with synthetic cord ensures high pressure resistance. Outer layer resistant to abrasion, weather conditions, and ozone. Used for spraying wet mortar: cement, plaster, and gypsum in construction work. Commonly used with plastering machines. Fitted with special ends for plastering. The NIAGARA LIGHT hose is an economical version with a slightly thinner wall (marked with the letter "L" at the end of the index). Standard length: 60 m and 40 m LIGHT version (or 120 m - contact Tubes International). Inner layer: black SBR/NR rubber. Reinforcement: synthetic cord. Outer layer: black SBR/NR rubber. Working pressure: 40 bar. Operating temperature: from -40°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for pneumatic transport of dry abrasive substances. Special hose design with exceptional abrasion resistance. The inner layer is smooth, made of black antistatic natural rubber with embedded alumina (Al2O3) ceramic beads, a material with high hardness. Built-in copper wire that, when grounded (connected to a grounded end), dissipates electric charges. The outer layer is made of black antistatic (R<106Ω) SBR/NR rubber resistant to abrasion and aging. The hose is intended for the transport of dry highly abrasive substances: e.g., dry cement, coal, coal dust, coke, solid fuels from secondary raw materials, minerals, ceramic powders, steel shot, glass shards, fiberglass. Used in steel mills, coking plants, power plants, cement plants, mines, glassworks, abrasive material factories, and insulation material factories. The advantage is the long lifespan of the hose in these applications – a traditional abrasion-resistant rubber hose may last only a few days, while the ALUSPHERE hose can last several months under the same conditions. Inner layer: ceramic beads embedded in black NR rubber. Reinforcement: synthetic cord. Outer layer: black SBR/NR rubber. Working pressure: 12 bar. Operating temperature: from -30°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for sandblasting. Thick inner layer made of rubber with very good abrasion resistance (50±5 mm³ according to ISO 4649 / DIN 53516). The inner and outer layers are antistatic, preventing the accumulation of electric charges. Used for sand and steel shot in abrasive blasting of steel structures, castings, concrete surfaces, etc. Commonly used in the metal and shipbuilding industries. Fitted with special nozzles for sandblasting. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black NR/SBR rubber. Reinforcement: synthetic cord. Outer layer: black NR/SBR rubber. Working pressure: 12 bar. Operating temperature: from -40°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, smooth, flat-wound hose designed for the discharge of bulk materials. Particularly used in installations exposed to vibrations and mechanical damage. Suitable for contact with food and in the pharmaceutical industry, being tasteless and odorless, in compliance with FDA requirements (21CFR177.2600). It is not subject to hydrolysis and is resistant to microbes. Also resistant to mineral oils, aging, atmospheric factors, ozone, UV, and many chemicals. Hose material: transparent polyurethane. Working pressure: from 0.135 bar to 1.03 bar, depending on the hose diameter. Operating temperature: -40°C to +90°C (temporarily +125°).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDry ice blasting hose – granulated solid carbon dioxide. Dry ice cleaning is used for removing coatings, adhesives, residues, etc., in various industrial sectors. The advantages of the process include no damage to the cleaned surface, no aggressive chemicals, no water in the process (compared to high-pressure water cleaning), and no abrasive residue (compared to sandblasting). Dry ice (solid carbon dioxide) has a temperature of up to -78.5°C (melting point), in granulated form, and sublimates to gas during the process. The DRY ICE hose is specifically designed for the transport of dry ice. The inner layer is smooth, made of anti-static synthetic rubber resistant to abrasion and low temperatures. The outer layer is anti-static, abrasion-resistant, weather-resistant, and ozone-resistant. It is fitted with quick couplings and specialized dry ice cleaning guns. Inner layer: black synthetic rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 10 bar. Operating temperature: from -55°C to +130°C.
