High-quality suction and pressure hose "FULL OHM" completely antistatic (Ω/T), designed for the transfer of highly flammable and chemically aggressive substances. The inner layer is made of perfluoroalkoxy polymer PFA (fluoropolymer with properties similar to Teflon), antistatic (R<10⁶ Ω), mirror-smooth, meeting high hygiene requirements (FDA, USP, European EU). Intermediate layers made of synthetic rubber, reinforced with synthetic cord and a steel wire spiral. The outer layer is MARBLE type (marbled), smooth, coated with polyethylene (UPE), antistatic (R<10⁶ Ω), meeting FDA requirements, odorless and tasteless, resistant to abrasion, ozone and aging, chemicals, and short-term action of aggressive acids. An advantage of the MARBLE layer is its low friction coefficient - the hose glides and does not soil the surfaces it contacts, making it easy to clean. Excellent chemical resistance of PFA and antistatic properties of both the inner and outer layers (R<10⁶ Ω) as well as across the wall of the hose (R<10⁹ Ω) make the hose a costly but technically ideal solution for applications requiring the highest safety in all explosion hazard zones (ATEX). Used in the chemical, petrochemical, pharmaceutical, and cosmetic industries, as well as in biotechnology. Not intended for sterilization in an autoclave. A version with additional built-in copper wires (M/T) is available on special order. Standards and requirements: Chemical hoses: EN 12115:2011. Food industry, contact with food: 1935/2004/EC, 2023/2006/EC (GMP); inner layer: 10/2011/EU, USP Class VI, FDA 21 CFR 177.1550; ISO 10993-4,-10,-11, non-cytotoxic (ISO 10993 Part 5); outer layer: FDA 21 CFR 177.1520. Contains no plasticizers, phthalates, or animal-derived substances. Explosive atmospheres: ATEX Directive (zones: 0, 1, 2, 20, 21, 22), EN 50014/IEC 60079-0. Confirmation of resistance and application conditions requires contact with Tubes International. Assembly: Use smooth fittings with a spigot ("tail" for the hose) that do not have sharp or high ribs that could cut or damage the inner layer of PFA when tightened. The diameter of the spigot should be precisely matched to the diameter of the hose to ensure tightness. Assembly with clamp sleeves or shell clamps. Inner layer: black PFA polymer. Reinforcement: synthetic cord, steel spiral. Outer layer: white-black UPE polyethylene, synthetic rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -35°C to +130°C.

Very lightweight, flexible suction and discharge hose designed for the transfer of chemical substances. Made from thermoplastic vulcanizate TPV – a material that combines the processing advantages of thermoplastic polymers (PP – polypropylene) with the properties of vulcanized rubber (EPDM). Good chemical resistance - similar to EPDM rubber allows for use with many substances, including acids (hydrochloric, sulfuric), bases, salts, alcohols, glycols, and ketones, concentrated detergents. Not recommended for fuels, oils, aromatic solvents. Resistant to weather conditions, aging, and ozone. Low weight and small bending radius of the hose ensure ease of handling, which can be an advantage when transferring from tankers and containers. Note: All hose sizes have branding indicating approximate working pressure (WP 10 bar). Confirmation of resistance and application conditions requires contact with Tubes International. Inner layer: thermoplastic rubber TPV. Reinforcement: polyester braid, steel spiral. Outer layer: thermoplastic rubber TPV. Working pressure for temperature +23°C: from 12 to 14 bar - depending on hose diameter. Operating temperature: from -30°C to +80°C (working pressure dependent on temperature).

Suction and discharge hose for the transfer of almost all aggressive chemical substances. Specifically designed for the petrochemical industry for fuels with high concentrations of aromatic hydrocarbons, hot oil, and solvents. Due to the high overall chemical resistance of FKM rubber, it can be used for aggressive chemicals, in many cases also at elevated temperatures. Used for the transshipment of chemicals from road and rail tankers. Inner layer made of smooth black FKM fluorine rubber. Reinforcement with synthetic cord and steel spiral. Outer layer made of CR chloroprene rubber, antistatic, resistant to weather conditions, ozone, abrasion, and oils. Two built-in copper wires for discharging electrostatic charges. Compliant with EN 12115:11 (type M). Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50°C. Vacuum: 0.9 bar. Inner layer: black FKM rubber (FPM, viton). Reinforcement: synthetic cord, steel spiral. Outer layer: black CR rubber. Working pressure: 16 bar. Operating temperature: from -25°C to +100°C.