Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon tube of the hose is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The braid is made of annealed AISI 304 stainless steel wire with a high tensile strength of 1700 N/mm², with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. A double braid should be used for higher pressures and where there is (within permissible limits) greater bending or kinking of the hose. Due to the unique properties of PTFE (wide operating temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. In cases where there is a risk of static electricity (danger of charge generation and accumulation), SMOOTHBORE hoses made of antistatic Teflon should be used – the antistatic version AS. The antistatic Teflon of version AS is black (contains appropriately distributed carbon in PTFE) and has a resistance of R<10^8 Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. The safety factor is 3:1; if a factor of 4:1 is required (e.g., according to EN 16643), the values should be multiplied by 0.75. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C above this temperature. For example, at a temperature of 170°C, the maximum working pressure for hose AF-SWDB-08 is: 250 bar – (170°C-130°C) x 0.75 = 250 bar – 30% = 175 bar. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: double braid of AISI 304 steel. Working pressure: from 70 bar to 360 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe HYPERLINE V (VISIFLON) hose features an inner layer made of high-quality corrugated PTFE, providing exceptional flexibility and vibration resistance. It has a polypropylene fiber braid characterized by low weight and high chemical resistance. At operating temperatures above +80°C, the maximum working pressure should be reduced by 5% for each 1°C increase in temperature. For example, at a temperature of 90ºC, the maximum working pressure for the hose AF-VFPB-19 is: 16 bar – (90°C-80°C) x 5 = 16 bar – 50% = 8 bar. There is an option to order a version with a black polymer braid (version PBB), with similar characteristics to version PB, for applications where bright colors cannot be used. Available versions: standard (orange) and antistatic (black). The antistatic Teflon of version AS contains evenly distributed carbon in the PTFE and has a resistance R <108 Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. Hose material: spiral corrugated PTFE (Teflon). Reinforcement: polypropylene braid. Working pressure: from 12.5 bar to 30 bar - depending on the hose diameter. Operating temperature: from -30°C to +100°C. Resistant to full vacuum up to a temperature of: +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon hose tube is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The braid is made of annealed AISI 316 steel wire, with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. Due to the unique properties of PTFE (wide operating temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. Safety factor 3:1; if a 4:1 factor is required (e.g., according to EN 16643), values should be multiplied by 0.75. At operating temperatures above +130ºC, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1ºC above this temperature. For example, at a temperature of 170ºC, the maximum working pressure for the hose AF-SWSB-316-06 is: 240 bar – (170ºC-130ºC) x 0.75 = 240 bar – 30% = 168 bar. Hose material: smooth PTFE (Teflon). Reinforcement: single braid of AISI 316 steel. Working pressure: from 80 bar to 240 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose designed for the transport and handling of crude oil, petrochemical products, and drilling cuttings mixed with crude oil (up to 50% aromatic compounds). The inner layer is made of black, smooth NBR/PVC rubber blend. Reinforcement with layers of durable synthetic cord. It features copper wires ensuring electrical continuity between the hose ends – provided there is proper connection to the fittings. The outer layer is made of chloroprene rubber (CR), flame-retardant, resistant to oil, seawater, abrasion, and weather conditions. Designed as a specialized OFFSHORE hose for operation on drilling platforms. Widely used on North Sea platforms, successfully utilized in land applications. Higher working pressure versions (20 bar, 27 bar) are also available upon special order, with specified breaking strength under tension (2T for 2”, 4T for 3”, and 7T for 4”, 5”, and 6”) and ABS type approval for the complete hose. Inner layer: black NBR/PVC rubber. Reinforcement: synthetic cord. Outer layer: black CR rubber. Working pressure: 17 bar. Operating temperature: from -20°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible suction hose designed for the transfer and distribution of liquid products in the petrochemical industry, containing up to 50% aromatic hydrocarbons (e.g., diesel, heating oil, gasoline with up to 50% aromatics). Suitable for fueling pumps. Inner layer made of black, smooth synthetic rubber. Reinforcement with synthetic cord. Features two copper wires ensuring electrical continuity between the hose ends (resistance R < 100 Ω between ends) – provided that the wires are correctly connected to the ends. Outer layer made of high-quality synthetic rubber resistant to oil and weather conditions. Hose compliant with the requirements of standard EN 1360:2013 type 1 class M for fuel distribution systems. Available in lengths up to 120 meters. Inner layer: black synthetic rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 16 bar. Operating temperature: from -30°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong fuel transfer hose for aviation fuel, designed for direct pressure refueling of aircraft. It can also be used in fuel transfer operations in airport tankers – dispensers, in cases not requiring high vacuum. It can be wound on reels. Suitable for aviation fuel for turbine engines (aviation kerosene, e.g., Jet A1), aviation gasoline, and fuels with aromatic hydrocarbon content up to 50%. Inner layer made of black, smooth NBR rubber. Reinforcement with layers of high-strength synthetic cord. Outer layer made of black, antistatic synthetic rubber, resistant to abrasion, weather conditions, and contact with oil. Antistatic outer layer, in accordance with EN ISO 1825 requirements, ensures the required low resistance of the hose between the ends (103 Ω < R < 106 Ω, ISO 8031). Compliant with requirements for aviation fuel hoses (type C/Ω) ISO 1825, API 1529:05, AS 2683, VG 95955, NFPA 407. Hoses with fluorescent marking visible at night and a transfer hose with an antistatic cord (type B/M) are available upon special request. Inner layer: black NBR rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 20 bar. Operating temperature: from -25°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, crystal-clear, flexible hose free of odor and taste, non-toxic, phthalate-free, and BPA (Bisphenol A) free. Designed for the transfer of milk and dairy products, used in milking equipment. The smooth, non-porous inner surface of the hose eliminates the problem of fat deposition, product particles, and bacterial growth. The built-in blue tape on the hose wall assures the customer of receiving the original TYGON® S3™ M-34-R hose, specifically designed for transporting raw milk. Meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA, 3-A, Japanese MHLW370(3-D). Cleaning by rinsing according to a special procedure. Compliant with REACH and California Proposition 65 - does not contain hazardous and prohibited substances. Full hose roll length: 30 m. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: up to +74°C. Brittleness temperature: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Zone of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTraditional, well-known, and proven over the years, hose made of natural red rubber. Easy to install due to its softness (hardness 45° Shore – A), flexibility, and elasticity. Resistant to abrasion, with low permeability for gases and good resistance to acids and bases. Used for liquids and gases for various industrial applications and in laboratories. Meets FDA requirements for food contact. Sterilization by steam for 30 minutes (1 bar, 141°C) or ethylene oxide. Full hose roll length is 25 m. The specified working pressure is determined relative to the burst pressure with a safety factor of 1:5. Material: natural rubber (NR). Operating temperature: from -30°C to +70°C (125°C for moist heat). Brittleness temperature: -40°C. Hardness: 45° Shore (A). Density: 1.13 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality PVC hose intended for water. Can be used for the transmission of drinking water (short-term contact with drinking water) – has been issued a compliance certificate in the Czech Republic according to the requirements of 409/2005 Sb for this application (contact Tubes International). For use in industry, agriculture, horticulture, and domestic applications. Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: transparent PVC. Working pressure at 20°C: from 10 bar to 17 bar - depending on the diameter of the hose. Operating temperature: from -5°C to +60°C. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThick, strong, and flexible pressure hose with steel reinforcement and an outer layer resistant to oil, for conveying saturated and superheated steam. The inner layer has good resistance to high temperature and saturated steam. It can be temporarily used for superheated steam at a temperature of 232°C and pressure of 18 bar; prolonged use with superheated steam reduces the hose's lifespan. The outer layer is resistant to oil, temperature, weather conditions, abrasion, and aging. The hose is used in the chemical, petrochemical, and energy industries, and in other industrial applications, particularly where resistance of the outer layer to oils, greases, and other petrochemical products is required. It is not intended for steam cleaners ("dry steam cleaners"). For steam, use special screw-on fittings designed for steam. To extend lifespan, the hose should be emptied of steam after use to avoid condensate accumulation. The VAPOFER EN ISO 6134 hose is antistatic (R ≤106Ω), compliant with standard EN ISO 6134/05 type 2 class B (Ω). Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black EPDM rubber. Reinforcement: double steel wire braid. Outer layer: black synthetic rubber, microperforated. Working pressure: 18 bar. Operating temperature: from -40°C to +210°C (temporarily up to +232°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose with magnetic base and valve for coolant supply - system 1/4". Components: 20 segments (L=300 mm), flat nozzle 1", valve with external thread 1/4" BSPT, and magnetic base with "tail" for 1/4" hose (end thread size 1/8" NPT). Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction hose supplied as a ready-made pipe, in various lengths, with mounted fittings, intended for sewage and water. Externally corrugated, almost smooth on the inside. The special profile makes the hose resistant to vacuum and kinking (returns to its shape). As a polyethylene hose, it has very good chemical resistance and resistance to biological corrosion (rotting, decay). It is flexible at low temperatures. The hose is used for emptying septic tanks and portable toilets, in construction, tourist facilities, marinas, and airports. Available lengths: from 10 m to 25 m. Hose material: yellow polyethylene profile (PE). Reinforcement: black polyethylene profile (PE). Vacuum: 0.95 bar (for diameter 51mm ÷ 76 mm); 0.85 bar (for diameter 102 mm). Operating temperature: from -40°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction hose supplied as a ready-made pipe, with mounted fittings, clamp, and rope, intended for sewage and water. Externally corrugated, almost smooth on the inside. The special profile makes the hose resistant to vacuum and kinking (returns to its shape). As a polyethylene hose, it has very good chemical resistance and resistance to biological corrosion (rotting, decay). It is flexible at low temperatures. Short sections of hose, 1 m in length with fittings, are used as protective hoses, resting on the edge of the channel opening, inside which a pressure cleaning hose or inspection hose with a camera is introduced. The clamp mounted on the fitting with an attached 7.5 m rope allows for maintaining the proper position of the protective hose. Length: 1 m. Hose material: yellow polyethylene profile (PE). Reinforcement: black polyethylene profile (PE). Vacuum: 0.95 bar. Operating temperature: from -40°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecial high-pressure water hose for snow guns, resistant to abrasion, aging, rot, UV radiation, weather conditions, and ozone. Designed for continuous operation at high pressure. Flexible at low temperatures. With an outer yellow coating, it is highly visible on snow, even in twilight. Supplied with CAMLOCK type fittings (socket C and plug E) in a high-pressure version of 60 bar made of AISI 316 stainless steel. Other lengths of DN52 hoses are also available (e.g., 25, 30, and 40 m). Maximum hose length is 60 m. Inner layer: EPDM rubber. Reinforcement: double polyester braid. Outer layer: yellow, special abrasion-resistant coating. Working pressure: 60 bar. Operating temperature: from -40°C to +80°C (water).
