Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsTraditional, well-known, and proven over the years, hose made of natural red rubber. Easy to install due to its softness (hardness 45° Shore – A), flexibility, and elasticity. Resistant to abrasion, with low permeability for gases and good resistance to acids and bases. Used for liquids and gases for various industrial applications and in laboratories. Meets FDA requirements for food contact. Sterilization by steam for 30 minutes (1 bar, 141°C) or ethylene oxide. Full hose roll length is 25 m. The specified working pressure is determined relative to the burst pressure with a safety factor of 1:5. Material: natural rubber (NR). Operating temperature: from -30°C to +70°C (125°C for moist heat). Brittleness temperature: -40°C. Hardness: 45° Shore (A). Density: 1.13 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality PVC hose intended for water. Can be used for the transmission of drinking water (short-term contact with drinking water) – has been issued a compliance certificate in the Czech Republic according to the requirements of 409/2005 Sb for this application (contact Tubes International). For use in industry, agriculture, horticulture, and domestic applications. Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: transparent PVC. Working pressure at 20°C: from 10 bar to 17 bar - depending on the diameter of the hose. Operating temperature: from -5°C to +60°C. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in the 1/4" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x14.5 cm or 100 cm. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 900 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in a 1/2" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and elasticity of the pipes. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x13.5 cm or 100 cm. Material: acetal. Working pressure: up to 2 bar. Maximum flow: 1700 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in the 3/8" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x14.5 cm or 100 cm. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 1500 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in the 1/4" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x145 mm, 100 mm, 200 mm, 300 mm, 400 mm, 500 mm, 600 mm, 700 mm, 800 mm, 900 mm, and 1000 mm. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 1136 l/hour. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsOil, grease, and hot chip resistant hose designed for low-pressure delivery of liquid or gaseous coolant during metal processing. It features a so-called shape memory, allowing for precise direction of the coolant flow. Supplied as ready-made hoses with an external BSP threaded connection ending with a metric external thread. Material: black PVC. Reinforcement: steel guiding cover, diameter DN 10 has an additional spiral cover made of nickel-plated steel sheet. Working pressure: 4 bar. Operating temperature: up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThick, strong, and flexible pressure hose with steel reinforcement and an outer layer resistant to oil, for conveying saturated and superheated steam. The inner layer has good resistance to high temperature and saturated steam. It can be temporarily used for superheated steam at a temperature of 232°C and pressure of 18 bar; prolonged use with superheated steam reduces the hose's lifespan. The outer layer is resistant to oil, temperature, weather conditions, abrasion, and aging. The hose is used in the chemical, petrochemical, and energy industries, and in other industrial applications, particularly where resistance of the outer layer to oils, greases, and other petrochemical products is required. It is not intended for steam cleaners ("dry steam cleaners"). For steam, use special screw-on fittings designed for steam. To extend lifespan, the hose should be emptied of steam after use to avoid condensate accumulation. The VAPOFER EN ISO 6134 hose is antistatic (R ≤106Ω), compliant with standard EN ISO 6134/05 type 2 class B (Ω). Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black EPDM rubber. Reinforcement: double steel wire braid. Outer layer: black synthetic rubber, microperforated. Working pressure: 18 bar. Operating temperature: from -40°C to +210°C (temporarily up to +232°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose with magnetic base and valve for coolant supply - system 1/4". Components: 20 segments (L=300 mm), flat nozzle 1", valve with external thread 1/4" BSPT, and magnetic base with "tail" for 1/4" hose (end thread size 1/8" NPT). Material: acetal. Working pressure: up to 3 bar. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose in a 3/4" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available lengths: 2x15 cm or 100 cm. Material: acetal. Working pressure: up to 1.4 bar. Maximum flow: 1900 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction hose supplied as a ready-made pipe, in various lengths, with mounted fittings, intended for sewage and water. Externally corrugated, almost smooth on the inside. The special profile makes the hose resistant to vacuum and kinking (returns to its shape). As a polyethylene hose, it has very good chemical resistance and resistance to biological corrosion (rotting, decay). It is flexible at low temperatures. The hose is used for emptying septic tanks and portable toilets, in construction, tourist facilities, marinas, and airports. Available lengths: from 10 m to 25 m. Hose material: yellow polyethylene profile (PE). Reinforcement: black polyethylene profile (PE). Vacuum: 0.95 bar (for diameter 51mm ÷ 76 mm); 0.85 bar (for diameter 102 mm). Operating temperature: from -40°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction hose supplied as a ready-made pipe, with mounted fittings, clamp, and rope, intended for sewage and water. Externally corrugated, almost smooth on the inside. The special profile makes the hose resistant to vacuum and kinking (returns to its shape). As a polyethylene hose, it has very good chemical resistance and resistance to biological corrosion (rotting, decay). It is flexible at low temperatures. Short sections of hose, 1 m in length with fittings, are used as protective hoses, resting on the edge of the channel opening, inside which a pressure cleaning hose or inspection hose with a camera is introduced. The clamp mounted on the fitting with an attached 7.5 m rope allows for maintaining the proper position of the protective hose. Length: 1 m. Hose material: yellow polyethylene profile (PE). Reinforcement: black polyethylene profile (PE). Vacuum: 0.95 bar. Operating temperature: from -40°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecial high-pressure water hose for snow guns, resistant to abrasion, aging, rot, UV radiation, weather conditions, and ozone. Designed for continuous operation at high pressure. Flexible at low temperatures. With an outer yellow coating, it is highly visible on snow, even in twilight. Supplied with CAMLOCK type fittings (socket C and plug E) in a high-pressure version of 60 bar made of AISI 316 stainless steel. Other lengths of DN52 hoses are also available (e.g., 25, 30, and 40 m). Maximum hose length is 60 m. Inner layer: EPDM rubber. Reinforcement: double polyester braid. Outer layer: yellow, special abrasion-resistant coating. Working pressure: 60 bar. Operating temperature: from -40°C to +80°C (water).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose with nozzle and valve with internal NPT thread in 1/2" system made of corrosion-resistant, solvent-resistant, oil and grease-resistant acetal, providing rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% position stability and does not cause damage to cutting tools. Standard length: 350 mm. Number of segments: 14 pcs. Material: acetal. Working pressure: up to 2 bar. Maximum flow: 1700 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose with nozzle and valve with internal NPT thread in 1/4" system made of corrosion-resistant, solvent-resistant, oil and grease-resistant acetal, providing rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensures 100% position stability and does not cause damage to cutting tools. Standard length: 360 mm. Number of segments: 20 pcs. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 900 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose with nozzle and valve with internal NPT thread in 3/8" system made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and not causing damage to cutting tools. Standard length: 360 mm. Number of segments: 16 pcs. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 1500 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose with nozzle and valve with external NPT thread in 1/2" system made of corrosion-resistant, solvent-resistant, oil and grease-resistant acetal, providing rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensures 100% position stability and does not cause damage to cutting tools. Standard length: 350 mm. Number of segments: 14 pcs. Material: acetal. Working pressure: up to 2 bar. Maximum flow: 1700 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose with nozzle and valve with external NPT thread in 1/2" LOC-LINE® system made of corrosion-resistant, solvent-resistant, oil and grease-resistant acetal, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% position stability and does not cause damage to cutting tools. Available lengths: 400 mm, 500 mm, and 600 mm. Material: acetal. Working pressure: up to 2 bar. Maximum flow: 2173 l/hour. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose with nozzle and valve with external NPT thread in 1/4" system made of corrosion-resistant, solvent-resistant, oil and grease-resistant acetal, providing rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and not causing damage to cutting tools. Standard length: 360 mm. Number of segments: 20 pcs. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 900 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose with nozzle and valve with external NPT thread in 1/4" LOC-LINE® system made of corrosion-resistant, solvent-resistant, oil and grease-resistant acetal, providing rigidity and flexibility of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Available lengths: 400 mm, 500 mm, and 600 mm. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 1136 l/hour. Operating temperature: up to +76°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoolant hose with nozzle and valve with external NPT thread in 3/8" system made of corrosion-resistant, solvent-resistant, oil and grease-resistant acetal, ensuring rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, providing 100% position stability and not causing damage to cutting tools. Standard length: 360 mm. Number of segments: 16 pcs. Material: acetal. Working pressure: up to 3 bar. Maximum flow: 1500 l/hour. Operating temperature: up to +65°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReel of coolant hose made of corrosion-resistant acetal, resistant to solvents, oils, and greases, providing rigidity and elasticity of the hoses. Designed for low-pressure transmission of air, water, oils, and other substances used in cooling processes and metalworking. Resistant to abrasion and vibrations, ensuring 100% positional stability and does not cause damage to cutting tools. Very easy to expand modular construction. Available in four sizes (diameter 1/4", 3/8", 1/2", and 3/4"). Available length: 15 m. Material: acetal. Working pressure: up to 3 bar, depending on diameter. Maximum flow: 1700 l/hour, depending on diameter. Operating temperature: up to +65°C.
