Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft rubber hose with an external stainless steel braid, designed for gasoline and petroleum-based oils such as diesel, heating oil, and lubricating oil. Installed in fuel and oil systems of small vehicles and industrial equipment. Can also be used for water, cooling fluids, non-oxidizing detergents, and air. Based on the requirements of standard DIN 73379. Inner layer made of smooth black NBR rubber. The external reinforcing braid made of stainless steel provides high pressure resistance and is corrosion-resistant. Maximum operating temperature depends on the medium: for gasoline, unleaded gasoline, fuels with up to 50% aromatic hydrocarbon content: +40ºC; for diesel: +80ºC; for water and ethylene glycol-based cooling liquids: +90ºC; for air: +80ºC; for liquid, non-oxidizing detergents: +80ºC. Inner layer: black NBR rubber. Reinforcement: external wire braid made of stainless steel AISI 304. Working pressure: from 10 bar to 20 bar - depending on the hose diameter. Operating temperature: from -35°C to +80°C (maximum operating temperature depends on the medium).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, abrasion-resistant suction hose designed specifically for the transfer of fuels, other liquid hydrocarbons, or for use as a general-purpose antistatic hose. Lighter and more flexible than standard rubber hoses, it has buoyancy (remains on the surface) in fresh and saltwater. Flat when at rest, which facilitates handling and storage. Intended for the transfer and transshipment of petrochemical products, oils, and fuels in refineries, industry, and transportation. Used for fueling ships, cleaning tanks, firefighting, and military applications. Meets the requirements of MIL-PRF-370J for liquid fuel hoses. Antistatic - features two externally longitudinally arranged copper wires ensuring electrical continuity between the hose ends easily accessible for proper connection to fittings (R < 0.02 Ω/m, exceeds the requirements of MIL-PRF-370J). The inner surface of the hose is smooth, causing no flow loss. Resistant to abrasion, weather conditions, hydrolysis, ozone, fuels, and commonly used chemicals (recommended pH range: 5 to 9). Resistant to longitudinal loads during unwinding and dragging. Hose material: polyurethane (PUR) embedded in the braid during the hose extrusion process. Working pressure: from 7 bar to 11 bar - depending on the hose diameter (the specified working pressure for fuel). Operating temperature: from -50°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong, with a thick wall and thick spiral, flexible hose designed for vacuum extraction and transport of abrasive materials such as sand, gravel, and grain. Suitable for all types of industries, particularly used for loading and unloading silos, vehicles, and suction excavators, as well as transloading from tankers, etc. The thick wall and very dense reinforcing spiral provide high resistance to vacuum. Smooth on the inside, non-compressible, not overly flexible but elastic, even at low temperatures. Excellent abrasion resistance, also resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. The hose is marked with an arrow indicating the correct direction of medium flow. The wall thickness of the hose is measured between the spirals. Other diameters may be available upon special request. The ECO 2.0 and ECO 2.5 hoses, regardless of their thickness, differ in construction and consequently in parameters. The ECO 2.0, due to its dense spiral, has greater resistance to vacuum but is less flexible, while the ECO 2.5, with a larger spiral pitch, is more flexible and elastic, especially in larger diameters. The ECO hose is produced in a manufacturing process compliant with sustainable development policies, using raw materials sourced from recycling clean waste from the production process, renewable energy, closed water cycles, and other innovations. Hose material: transparent polyester-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between spirals: 2.0 mm (ECO 2.0), 2.5 mm (ECO 2.5). Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, economical suction and discharge hose for universal applications. Smooth inside, slightly corrugated outside. Designed for water, light chemicals, sludges and wastewater, plant protection products, and other liquids (avoiding fats, oils, and hydrocarbons). Also suitable for air, vacuum transfer of dust, powders, light granules, and other mildly abrasive bulk materials. Abrasiveness and potential static electricity issues should be considered. Widely used in agriculture, horticulture, and domestic applications. Hose material: green transparent PVC. Reinforcement: white spiral made of rigid PVC. Vacuum at 20°C: 0.6 bar. Operating temperature: from -20°C to +60°C. As the operating temperature increases, the working vacuum value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight smooth-walled PTFE hose with antistatic properties and excellent chemical resistance. The conductivity and dissipation of electric charges are achieved by the addition of up to 2.5% carbon black - PTFE AS. This allows for a reduction in the resistance of the hose material and meets the requirements of the EN12115 standard, which requires resistance between the ends of the hose to be less than 106 Ω/m. The hose is particularly intended for aggressive chemically non-conductive substances, such as organic solvents, whose flow in a standard Teflon hose can cause the accumulation of electric charges and associated hazards. High purity and distribution of the carbon additive in PTFE ensure compliance with FDA 21 CFR 178.3297 regarding materials approved for temporary contact with food. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). The use of high-quality plug couplings is possible. Safety factor n=4:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Material: antistatic PTFE (Teflon), black. Shore hardness (D): 60. Working pressure: from 5.5 to 12 bar. Operating temperature: from -200°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details45° ELBOW RADIATOR intended for engine cooling systems in vehicles and automotive-type engines (for water, ethylene glycol-based coolants). Meets the requirements of standard SAE J20 R4 Class D-1. Available with arm lengths of 200, 250, and 300 mm. Working pressure: from 0.6 bar to 4.1 bar, depending on the elbow diameter. Operating temperature: from -40°C to +125°C. Safety factor (burst pressure / maximum working pressure) 3:1. coupling material: black EPDM rubber. Reinforcement: textile braid.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone elbow 135° reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, the version with a fluorosilicone inner layer is recommended. Standard arm length: 102 mm. Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers. Working pressure: from 2 bar to 8.12 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose designed for unleaded gasoline, diesel oil, and liquid fuels containing up to 50% aromatic compounds. Used in industry and transportation for the transfer and handling of petrochemical products, in tank trucks, at road and rail loading and unloading terminals for fuels. Inner layer made of black, smooth, antistatic (R ≤ 10^6 Ω) NBR rubber (NBR1). Reinforced with layers of high-strength cord. Equipped with two copper wires ensuring electrical continuity between the hose ends, provided that they are properly connected. Outer layer made of black, antistatic (R ≤ 10^6 Ω) synthetic rubber, self-extinguishing, resistant to abrasion, oil, ozone, and weather conditions. Wall resistance across the hose R ≤ 10^9 Ω (type M/T). Compliant with standards EN12115:11 (16 bar), EN 1761 (10 bar), ISO 2929 (10 bar), TRbF. Excellent resistance to petrochemical products, strong construction, and antistatic properties of both inner and outer layers, built-in antistatic wires, recommend this hose for demanding applications, including in explosion hazard zones. In any case, however, use in explosion hazard zones (ATEX) should be preceded by a risk analysis conducted by a specialist. A version without wire (type Ω/T) is available on special order. Inner layer: black, smooth NBR rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 16 bar. Operating temperature: from -30°C to +90°C (temporarily up to +110°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong general-purpose PVC hose with specially reinforced wall and braid construction. Good resistance to kinking. Designed for water, air, and light chemicals in agriculture, horticulture, and industry. Inner layer: black PVC. Reinforcement: polyester braid. Outer layer: yellow PVC. Working pressure at 20°C: 10 bar. Operating temperature: from -5°C to +60°C. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose for oils and fuels. Lighter and more flexible than standard rubber hoses. Flat at rest, facilitating handling and storage. Designed for the transfer and loading of petrochemical products, oils, and fuels in refineries, industry, and transportation. Used for fueling ships, cleaning tanks, firefighting, and military applications. The hose is constructed with a high-strength polyester-polyamide braid, fully embedded in an NBR/PVC compound. It features copper wires ensuring electrical continuity between the hose ends—provided proper connection to the fittings. The inner surface of the hose made of NBR/PVC is smooth, causing no flow loss, while the outer surface made of NBR/PVC is slightly longitudinally ribbed, enhancing abrasion resistance and protection against contact with hot elements. Externally resistant to abrasion, ozone, weather conditions, oil, fuels, and a wide range of chemicals. Does not require cleaning and drying. Resistant to longitudinal loads—during unwinding and pulling (the longitudinal force should never exceed 1/3 of the specified breaking strength; the installation of fittings should consider the longitudinal force). Standard color is greenish-gray (army green). Hose material: greenish-gray NBR/PVC compound embedded in a polyester-polyamide braid during the hose extrusion process. Working pressure: from 16 to 20 bar, depending on the hose diameter. Operating temperature: from -20°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRubber molded hose without reinforcement, flexible and stretchable (in diameter) with a special corrugated shape, ensuring resistance to kinking when bending and the ability to cut into sections of required length. Produced in lengths of 1 m, which can be cut and easily shaped in installation. Available in a basic version made of EPDM rubber, for water, cooling fluids, resistant to diluted acids and bases, at elevated temperature and ozone. Operating temperature range from -40°C to +135°C (TUBANO) and in a version with increased external oil resistance, made of a different synthetic rubber. Operating temperature range from -30°C to +120°C (TUBANO OIL). Hose material: molded EPDM rubber. Working pressure: 1.5 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, exceptionally soft and flexible, universal laboratory hose free of phthalates (DEHP). An excellent solution for complex laboratory equipment installations requiring small bend radii and multiple curves. This ultra-soft hose is resistant to twisting and kinking and remains flexible at low temperatures (down to -55°C). Due to its softness, it does not require high forces for compression, making it an ideal solution for peristaltic pumps with low torque or battery-powered. It has a longer lifespan in peristaltic pump applications compared to typical silicone hoses, while also possessing good chemical resistance to a range of corrosive media (acids, bases, salts, alcohols). Compliant with FDA requirements for food contact and REACH. Sterilization only with ethylene oxide. Full hose roll length: 15 m. The specified working pressure is defined relative to the burst pressure with a safety factor of 1:5. Material: PVC (special, DEHP-free). Maximum operating temperature: +52°C. Brittleness temperature: -55°C. Hardness: 40° Shore (A). Density: 1.1 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal flexible rubber pressure hose, intended for air, cold and hot water, and light chemicals (except acids). Resistant to acetates and ketones. Can be used for dispersive water-based epoxy and polyurethane paints. Not suitable for oils, fuels, aromatic hydrocarbons, cellulose paints, chlorinated rubber, and others containing aromatic solvents (e.g., toluene, xylene) or gasoline. For chemical applications, we recommend contacting Tubes International. The hose has a strong construction and low elongation under pressure. Suitable for use on reels. Inner layer electrically conductive (R<106 Ω, EN ISO 8031), outer layer resistant to ozone and weather conditions. Inner layer: black EPDM rubber. Reinforcement: textile braid (PVA - polyvinyl alcohol). Outer layer: black EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +95°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose for demanding, versatile applications in the food industry. Excellent for the transfer of various types of food products such as: olive oil, wine, beer, fruit juices, milk, fats, and alcohols with a concentration of up to 96%. The inner layer is odorless and tasteless. It does not contain phthalates and bisphenol A, as well as polycyclic aromatic hydrocarbons (PAH Free), in accordance with ZEK 01.4-08 Cat.1. Tested for heavy metals. The outer layer is resistant to weather conditions and ozone. Standards and requirements: Food industry, food contact 1935/2004/EC and EC 2023/2006/EC (GMP). The inner layer complies with FDA 21 CFR 177.2600, BfR XXI cat. 2, D.M. 21/03/73, 3-A Sanitary Standard 18-03 class II. Inner layer: white, smooth synthetic rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: blue synthetic rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, semi-transparent, strong and flexible reinforced hose designed for higher pressures. Made of polyether - polyurethane, free of plasticizers, exceptionally resistant to abrasion and tearing, characterized by a small bending radius and flexibility even at low temperatures. Withstands cyclic temperature changes. Resistant to oils, greases, fuels, and a range of chemicals. Used in various industrial sectors: transfer of abrasive and viscous products, sludges and pastes, transfer of granules and powders, lubrication and degreasing, for cooling fluids in automotive applications, for air in pneumatics and industrial automation. Used in the food and cosmetic industries - meets FDA 21 CFR 177.1680 and FDA 21 CFR 177.2600 requirements for food contact and NSF-61 for use with drinking water (with hose length limitations depending on diameter). Full hose roll length 30 m (from internal diameter 31.8 mm - 15 m). Working pressure defined relative to burst pressure with a safety factor of 1:4. Material: tygothane® - polyurethane - polyether (PU). Operating temperature: from -73°C to +82°C. Brittleness temperature: -73°C. Hardness: 85° Shore (A). Density: 1.12 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDry ice blasting hose – granulated solid carbon dioxide. Dry ice cleaning is used for removing coatings, adhesives, residues, etc., in various industrial sectors. The advantages of the process include no damage to the cleaned surface, no aggressive chemicals, no water in the process (compared to high-pressure water cleaning), and no abrasive residue (compared to sandblasting). Dry ice (solid carbon dioxide) has a temperature of up to -78.5°C (melting point), in granulated form, and sublimates to gas during the process. The DRY ICE hose is specifically designed for the transport of dry ice. The inner layer is smooth, made of anti-static synthetic rubber resistant to abrasion and low temperatures. The outer layer is anti-static, abrasion-resistant, weather-resistant, and ozone-resistant. It is fitted with quick couplings and specialized dry ice cleaning guns. Inner layer: black synthetic rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 10 bar. Operating temperature: from -55°C to +130°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for conveying wine, fruit juices, beer, and water, with smaller diameters. Can be used with drum reels. Completely free of animal-derived ingredients, phthalates, plasticizers, and nitrosamines. Highly resistant to cleaning and disinfection processes used in the food industry. Inner layer is tasteless and odorless. Outer layer is abrasion and aging resistant. Standards and requirements: Food industry, food contact 1935/2004/EC, 2023/2006/EC (GMP). Inner layer compliant with FDA, D.M. 21/03/73, BfR II. Inner layer: white smooth technopolymer. Reinforcement: synthetic braid. Outer layer: blue smooth technopolymer. Working pressure: 10 bar. Operating temperature: -20°C to +80°C (temporarily up to +90°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBlack, opaque, high-quality flexible hose made of fluorine rubber, resistant to solvents, fuels, oils, aggressive chemicals, also under elevated temperature conditions. Used for cleaning solvents (dry cleaning, solvent recovery systems), aggressive chemicals, acids and bases, hot oils and fuels. Suitable for peristaltic pumps. Resistant to ozone, sunlight, and weather conditions. The opaque black wall of the hose completely protects light-sensitive substances. The production process of the hose with post-vulcanization heating removes any residues and ensures minimal outgassing, required in vacuum and space applications. Full roll length of the hose is 15 m. Working pressure specified relative to burst pressure with a safety factor of 1:5. Material: fluoroelastomer (FKM). Maximum operating temperature: +204°C. Brittleness temperature: -51°C. Hardness: 60° Shore (A). Density: 1.90 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible and bendable, chemically and thermally resistant two-layer hose designed for the discharge and transfer of the most chemically aggressive vapors, gases, dust, and fibers (non-abrasive), as well as for the blowing of hot air. Very good chemical resistance to aggressive chemicals due to the internal layer of PTFE. In the standard version, the internal layer of white natural PTFE meets food industry requirements (FDA). In the antistatic version EL, the black internal layer of PTFE is electrically conductive (R ≤106 Ω). The hose features high compressibility - up to 1:6, a strong construction resistant to vibrations, stretching, and tearing, and impact resistance due to the external spiral. Resistant to UV radiation, ozone, and aging. Used in the chemical, petrochemical, and food industries. Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with bridge clamps (left-handed). Chemical resistance verification - chemical resistance table for PTFE (preliminary selection), confirmation of resistance and application conditions - by Tubes International. Standard length: from 2 to 10 m. Hose material internal layer: white PTFE film - standard version HYTEF, black conductive PTFE film - antistatic version HYTEF EL. Hose material external layer: black polyethylene fabric coated with CSM rubber. Reinforcement: external spiral made of galvanized steel wire and sheet. Operating temperature: from -35°C to +175°C (temporarily up to +190°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, highly flexible and bendable, chemically resistant hose designed for the extraction and transfer of aggressive chemical vapors from solvents, paints, hydrocarbons, chemicals, etc. Thanks to the conductive FKM rubber, it has antistatic properties (surface resistance R <106 Ω). Very good resistance to oil, aromatic substances, most acids, and chemicals. Excellent resistance to elevated temperatures. Resistant to UV radiation and ozone. Characterized by high compressibility - up to 1:6, strong construction resistant to vibrations and stretching, impact resistance due to the external spiral. Used in the paint, chemical, and paper industries. Also available with a stainless steel spiral (from a diameter of 80 mm). Hose installation on couplings with bridge clamps (left-handed). Chemical resistance verification - chemical resistance table for FKM (preliminary selection), confirmation of resistance and application conditions - by Tubes International. Standard length: from 2 to 10 m. Hose material: polyester fabric coated with FKM, antistatic, externally black. Reinforcement: external spiral made of steel sheet and wire. Operating temperature: from -25°C to +210°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight and with excellent flexibility, the hose is designed for the discharge of oil vapors, dust, and light bulk materials. Resistant to microorganisms and hydrolysis. Compliant with FDA requirements and European Directives. Hose material: transparent polyether-polyurethane. Reinforcement: steel wire spiral. Wall thickness measured between the spiral: 0.4 mm. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, soft fuel hose made of special NBR rubber resistant to methyl ester of fatty acid rapeseed oil (RME). Reinforcement with synthetic textile braid. Outer layer made of chloroprene rubber (CR), antistatic, self-extinguishing, resistant to abrasion, temperature, and aging. Particularly recommended for biofuels based on methyl esters of fatty acids (FAME) such as biodiesel B10, B20, B100. Resistant to methyl ester of fatty acid rapeseed oil (RME). Can also be used for regular diesel fuel. Inner layer: special NBR rubber. Reinforcement: synthetic textile braid. Outer layer: CR rubber. Working pressure: 15 bar. Operating temperature: from -30°C to +100°C (temporarily up to +120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, thick, flexible hose designed for suction and transport of abrasive materials: sand, gravel, debris, leaves, and other contaminants. Intended for use in street, square, and road cleaning. Used in sweepers and other municipal and road service equipment. The special design of the P7 M STREET hose ensures that despite its large wall thickness (1.4 mm), it has a smaller bending radius (1.2 x D) than standard hoses of this thickness. The folds of the hose between the spiral at the bend turn outward, reducing flow resistance and wear. Flexible, low-compressible, smooth inside, and elastic even at low temperatures. Good abrasion resistance, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Wall thickness is measured between the spiral. Installation on fittings with bridge clamps (right-handed). Other diameters may be available upon special request. Hose material: transparent and black polyether – polyurethane. Wall thickness: 1.4 mm. Reinforcement: steel wire spiral. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight transparent smooth-walled hose made of natural (non-regenerated) fluoropolymer PFA (perfluoroalkoxy), a material with properties similar to PTFE. The hose features excellent chemical resistance, dimensional and shape thermal stability, a very smooth, micropore-free internal and external surface, high pressure resistance, and crack resistance due to excessive stress. Good transparency of the hose allows for easy observation of level or flow. UV resistant. Designed for low-pressure installations of aggressive chemicals or when high purity and chemical inertness of the hose material are required. Commonly used in laboratories, chemical and pharmaceutical industries. Due to its excellent insulating properties (dielectric strength 3 to 4 times greater than PTFE), it is used in the electronics and semiconductor industries. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 4:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Hose material: PFA. Shore hardness (D) 60. Operating temperature: from -200°C to +260°C. Working pressure: from 7 bar to 19.5 bar - depending on the diameter and wall thickness of the hose.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and pressure hose made according to platinum-enhanced technology. Steam sterilization (max. +135°C at 3.5 bar pressure for 30 min.). The inner layer meets FDA, USP Class VI, D.M. 21/03/73, and EU Regulation No. 10/2011 requirements. The outer layer meets USP Class VI, FDA, and European Pharmacopoeia standards. Hose compliant with EC 1935/2004 and 2023/2006/EC (GMP). Free from animal-derived substances, phthalates, adipates, and materials subject to restrictions of Directive EC 1907/2006 (REACH). Safety factor 3:1. The specified bend radius applies to static pressure. Working pressure (20°C): from 4 bar to 10 bar, depending on hose diameter. Inner layer: white smooth fluoropolymer PFA. Dynamic. Reinforcement: polyester braiding, AISI 302 steel spiral. Outer layer: transparent silicone. Operating temperature: from -30°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, reinforced polyester braided hose, odorless and tasteless, non-toxic, free from phthalates and BPA (Bisphenol A). Designed for the transfer and dispensing of food products under higher pressure. Smooth, non-porous inner surface of the hose eliminates the problem of product particle settlement and bacterial growth. Resistant to alkaline cleaning agents. Meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA, NSF-51, NSF-61, 3-A, Japanese #370/1959 and MHLW370(3-D). Compliant with REACH and California Proposition 65 - does not contain hazardous and prohibited substances. Possible sterilization with ethylene oxide. After installing fittings with appropriate hygienic design, cleaning by CIP method is possible. Full hose roll length 15 m (from internal diameter 38.1 mm - 6 m). Working pressure defined relative to burst pressure with a safety factor of 1:4. Material: PVC (special). Maximum operating temperature: up to +74°C. Brittleness temperature: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Zone of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction and discharge hose designed for the transport and handling of crude oil, petrochemical products, and drilling cuttings mixed with crude oil (up to 50% aromatic compounds). Inner layer made of black, smooth NBR/PVC rubber blend. Reinforced with layers of durable synthetic cord and steel spiral. It has copper wires ensuring electrical continuity between the hose ends – provided that it is properly connected to the fittings. Outer layer made of CR chloroprene rubber, flame-retardant, resistant to oil, seawater, abrasion, and weather conditions. Designed as a specialized OFFSHORE hose for operation on drilling platforms. Widely used on North Sea platforms, successfully utilized in land applications. Higher working pressure versions (20 / 27 / 30 / 35 bar) available on special order, with specified breaking strength under tension (up to 2T for 2”, 4T for 3”, and 7T for 4”, 5”, and 6”) and ABS type approval for the complete hose. Inner layer: black NBR/PVC rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black CR rubber. Working pressure: from 17 bar to 20 bar - depending on the hose diameter. Operating temperature: from -20°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose intended for the transfer of aviation fuel (jet fuel, kerosene, e.g., Jet A1) and petrochemical products containing up to 50% aromatic compounds, primarily for draining fuel from aircraft tanks, loading and unloading airport tankers and fuel dispensers. The outer layer is antistatic, abrasion-resistant, oil-resistant, and weather-resistant. It features copper wires ensuring electrical continuity (R < 100 Ω) between the hose ends and dissipation of electrostatic charges. Compliant with requirements for aviation fuel hoses (type E/M) ISO 1825, API 1529:05, AS 2683, VG 95955, NFPA 407. Inner layer: black NBR rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: black synthetic rubber. Working pressure: 20 bar. Vacuum: 0.85 bar. Operating temperature: from -25°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong suction-discharge hose for aviation fuel, intended for filling and emptying aircraft tanks, loading and unloading airport tankers and fuel dispensers. As a hose without metal components, it can be used for direct filling and emptying of aircraft tanks. It can be wound on reels. Suitable for aviation fuel for turbine engines (aviation kerosene, e.g., Jet A1), aviation gasoline, and fuels with aromatic hydrocarbon content up to 50%. Inner layer made of black, smooth NBR rubber. Reinforcement with layers of high-strength synthetic cord and a polymer spiral (PET). Outer layer made of black, antistatic synthetic rubber, resistant to abrasion, weather conditions, and contact with oil. Antistatic outer layer ensures the required low resistance of the hose between the ends (10^3 Ω < R < 10^6 Ω, ISO 8031). Compliant with requirements for aviation fuel hoses (type F/Ω) API 1529:05, AS 2683, VG 95955, NFPA 407. Other diameters and hoses with fluorescent markings visible at night are available upon special order. Inner layer: black NBR rubber. Reinforcement: synthetic cord, PET spiral. Outer layer: black synthetic rubber. Working pressure: 20 bar. Operating temperature: from -25°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHyperline FX SS AS SI WHITE hose is a lightweight, flexible Teflon hose. Due to its properties, it is recommended for the transfer of hot media and CIP applications. The hose can be supplied by the meter or as complete assemblies. The outer layer made of white silicone facilitates cleanliness maintenance. This solution also protects the operator from burns. High resistance of the inner layer to prolonged exposure to steam. At operating temperatures above +160°C, the maximum working pressure specified in the technical data should be reduced by 1% for each 1°C above this temperature. For example, at a temperature of 180°C, the maximum working pressure for hose AF-FXSS-10 is: 100 bar – (180°C-160°C) x 1 = 100 bar – 20% = 80 bar. The specified value of vacuum is defined for operating temperatures up to 150°C. The hose is standardly available in an antistatic version and is also available in a natural PTFE version. Hose material: smooth inside, corrugated outside, antistatic PTFE (Teflon). Reinforcement: single braid of AISI 304 steel with an additional protective layer of white silicone rubber. Working pressure: from 50 bar to 110 bar - depending on the hose diameter. Operating temperature: from -70°C to +204°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSmoothbore Teflon hose version with reinforced wall made of specially processed Teflon (reduced microporosity) for use with high-pressure gases and other penetrating substances, in double steel braid. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C increase in temperature. Installation: use AF-TL series fittings and sleeves... Hose material: smooth PTFE. Reinforcement: double braid of 304 steel. Working pressure: from 180 bar to 225 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCHEMFLUOR TH hose is a flexible Teflon hose designed for high-pressure hydraulic, pneumatic, and gas installations. The inner layer made of conductive Teflon prevents the accumulation of electrostatic charges. Hose material: black, conductive PTFE. Reinforcement: AISI 304 steel braid. Operating temperature: from -50°C to +200°C. Working pressure: 345 bar. Burst pressure at 20°C: 1100 bar. Burst pressure at 200°C: 820 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon tube of the hose is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The heavy-duty HW version is recommended for harsher working conditions, gases (up to 100 bar), and applications where there are cyclic temperature changes. The braid is made of annealed AISI 304 stainless steel wire with a high tensile strength of 1700 N/mm², with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. Due to the unique properties of PTFE (wide temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. In cases where there is a risk of static electricity (danger of charge generation and accumulation), SMOOTHBORE hoses made of antistatic Teflon should be used – the antistatic version AS. The antistatic Teflon of version AS is black (contains appropriately distributed carbon in PTFE) and has a resistance R <10⁸ Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. The safety factor is 3:1; if a 4:1 factor is required (e.g., according to EN 16643), the values should be multiplied by 0.75. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C above this temperature. For example, at a temperature of 170°C, the maximum working pressure for the hose AF-HWDB-10 is: 240 bar – (170°C-130°C) x 0.75 = 240 bar – 30% = 168 bar. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: double braid of AISI 304 steel. Working pressure: from 40 bar to 350 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon tube of the hose is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The braid is made of annealed AISI 304 stainless steel wire with a high tensile strength of 1700 N/mm², with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. A double braid should be used for higher pressures and where there is (within permissible limits) greater bending or kinking of the hose. Due to the unique properties of PTFE (wide operating temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. In cases where there is a risk of static electricity (danger of charge generation and accumulation), SMOOTHBORE hoses made of antistatic Teflon should be used – the antistatic version AS. The antistatic Teflon of version AS is black (contains appropriately distributed carbon in PTFE) and has a resistance of R<10^8 Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. The safety factor is 3:1; if a factor of 4:1 is required (e.g., according to EN 16643), the values should be multiplied by 0.75. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C above this temperature. For example, at a temperature of 170°C, the maximum working pressure for hose AF-SWDB-08 is: 250 bar – (170°C-130°C) x 0.75 = 250 bar – 30% = 175 bar. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: double braid of AISI 304 steel. Working pressure: from 70 bar to 360 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe HYPERLINE V (VISIFLON) hose features an inner layer made of high-quality corrugated PTFE, providing exceptional flexibility and vibration resistance. It has a polypropylene fiber braid characterized by low weight and high chemical resistance. At operating temperatures above +80°C, the maximum working pressure should be reduced by 5% for each 1°C increase in temperature. For example, at a temperature of 90ºC, the maximum working pressure for the hose AF-VFPB-19 is: 16 bar – (90°C-80°C) x 5 = 16 bar – 50% = 8 bar. There is an option to order a version with a black polymer braid (version PBB), with similar characteristics to version PB, for applications where bright colors cannot be used. Available versions: standard (orange) and antistatic (black). The antistatic Teflon of version AS contains evenly distributed carbon in the PTFE and has a resistance R <108 Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. Hose material: spiral corrugated PTFE (Teflon). Reinforcement: polypropylene braid. Working pressure: from 12.5 bar to 30 bar - depending on the hose diameter. Operating temperature: from -30°C to +100°C. Resistant to full vacuum up to a temperature of: +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon hose tube is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The braid is made of annealed AISI 316 steel wire, with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. Due to the unique properties of PTFE (wide operating temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. Safety factor 3:1; if a 4:1 factor is required (e.g., according to EN 16643), values should be multiplied by 0.75. At operating temperatures above +130ºC, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1ºC above this temperature. For example, at a temperature of 170ºC, the maximum working pressure for the hose AF-SWSB-316-06 is: 240 bar – (170ºC-130ºC) x 0.75 = 240 bar – 30% = 168 bar. Hose material: smooth PTFE (Teflon). Reinforcement: single braid of AISI 316 steel. Working pressure: from 80 bar to 240 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong suction hose designed for the transport and handling of crude oil, petrochemical products, and drilling cuttings mixed with crude oil (up to 50% aromatic compounds). The inner layer is made of black, smooth NBR/PVC rubber blend. Reinforcement with layers of durable synthetic cord. It features copper wires ensuring electrical continuity between the hose ends – provided there is proper connection to the fittings. The outer layer is made of chloroprene rubber (CR), flame-retardant, resistant to oil, seawater, abrasion, and weather conditions. Designed as a specialized OFFSHORE hose for operation on drilling platforms. Widely used on North Sea platforms, successfully utilized in land applications. Higher working pressure versions (20 bar, 27 bar) are also available upon special order, with specified breaking strength under tension (2T for 2”, 4T for 3”, and 7T for 4”, 5”, and 6”) and ABS type approval for the complete hose. Inner layer: black NBR/PVC rubber. Reinforcement: synthetic cord. Outer layer: black CR rubber. Working pressure: 17 bar. Operating temperature: from -20°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible suction hose designed for the transfer and distribution of liquid products in the petrochemical industry, containing up to 50% aromatic hydrocarbons (e.g., diesel, heating oil, gasoline with up to 50% aromatics). Suitable for fueling pumps. Inner layer made of black, smooth synthetic rubber. Reinforcement with synthetic cord. Features two copper wires ensuring electrical continuity between the hose ends (resistance R < 100 Ω between ends) – provided that the wires are correctly connected to the ends. Outer layer made of high-quality synthetic rubber resistant to oil and weather conditions. Hose compliant with the requirements of standard EN 1360:2013 type 1 class M for fuel distribution systems. Available in lengths up to 120 meters. Inner layer: black synthetic rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 16 bar. Operating temperature: from -30°C to +55°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong fuel transfer hose for aviation fuel, designed for direct pressure refueling of aircraft. It can also be used in fuel transfer operations in airport tankers – dispensers, in cases not requiring high vacuum. It can be wound on reels. Suitable for aviation fuel for turbine engines (aviation kerosene, e.g., Jet A1), aviation gasoline, and fuels with aromatic hydrocarbon content up to 50%. Inner layer made of black, smooth NBR rubber. Reinforcement with layers of high-strength synthetic cord. Outer layer made of black, antistatic synthetic rubber, resistant to abrasion, weather conditions, and contact with oil. Antistatic outer layer, in accordance with EN ISO 1825 requirements, ensures the required low resistance of the hose between the ends (103 Ω < R < 106 Ω, ISO 8031). Compliant with requirements for aviation fuel hoses (type C/Ω) ISO 1825, API 1529:05, AS 2683, VG 95955, NFPA 407. Hoses with fluorescent marking visible at night and a transfer hose with an antistatic cord (type B/M) are available upon special request. Inner layer: black NBR rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber. Working pressure: 20 bar. Operating temperature: from -25°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, crystal-clear, flexible hose free of odor and taste, non-toxic, phthalate-free, and BPA (Bisphenol A) free. Designed for the transfer of milk and dairy products, used in milking equipment. The smooth, non-porous inner surface of the hose eliminates the problem of fat deposition, product particles, and bacterial growth. The built-in blue tape on the hose wall assures the customer of receiving the original TYGON® S3™ M-34-R hose, specifically designed for transporting raw milk. Meets hygiene and food contact requirements: European 1935/2004/EC and 10/2011 EU (for conditions and substances according to certification), American FDA, 3-A, Japanese MHLW370(3-D). Cleaning by rinsing according to a special procedure. Compliant with REACH and California Proposition 65 - does not contain hazardous and prohibited substances. Full hose roll length: 30 m. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: PVC (special). Maximum operating temperature: up to +74°C. Brittleness temperature: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Zone of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
