Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsBall fitting - insert for a nut. Material: brass. Working pressure: 40 bar. Operating temperature: from -10°C to +90°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFitting straight INTERLOCK with BSP female thread, 60° cone with an O-ring, for hose type 4SH, R13 and R15. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBar mounting for hoses pneumatic. facilitates and speeds up design installations, reduces space installation, increases resistance to vibration. color: blue.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMini actuator double-acting operation ISO 6432 STD, type 113, It has been designed to work with filtered air, oiled or non-oiled, and does not require additional maintenance operations. A stainless steel sleeve was used to make the actuator. The dimensions of the external covers of some diameters have been reduced, which allows mounting the actuators in difficult and confined spaces. The service life of actuators with NBR seals is 15 million cycles, with polyurethane ones 30 million cycles. The presented values should not be treated as binding or guaranteed, but only as a reference due to the variability of many factors, including loads radial and axial, speed, temperature, czy losses air (values limit). Piston diameter: Ø 16, 20 and 25 mm. stroke working: od 10 for 500 mm. pressure working: od 0.6 up to 10 bar. Sealing: polyurethane, NBR. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA nut for ring double-cone Intended for mounting line for systems lubrication at use typical ends tube and seamless pipes of steel or brass. Material: steel carbon, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNipple with a parallel male thread, type A1, intended for connecting pneumatic components (including hoses) to one another. A tight connection usually requires additional sealing: PTFE tape or sealant for a tapered thread, or aluminum or copper washers for a parallel thread. Material: nickel-plated brass. Working pressure: 60 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecial version cover PYROJACKET intended mainly for aviation (made in accordance with the standard SAE Aerospace Standard 1072E), industry railway (compliant with DIN EN 45545-2:2013-08) and marine. additional certified is in diameter 13 mm ÷ 127 mm through DNV for temperature +800°C through 30 minutes (ISO 15540) and through MSHA (for use in mines). On request, a VCO version with flame-retardant hook-and-loop (velcro) is available in the diameter range from 22 mm to 140 mm, in lengths up to 30 meters. The hook-and-loop mounting means that the cover can be easily installed without disconnecting lines, cables or pipes. Material: fiber glass coated silicone in color rust. Operating temperature: from -54°C to +260°C (up to +1093°C through 15 ÷ 20 minutes), (up to +1650°C through 15 ÷ 30 seconds).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCutting ring for a nut with a metric thread type AI 13740 made of brass. Range of external diameters of the joined pipes from 4 to 22 mm. Standard: EN 1254-2. Material: brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAn AKBO hot-water gun. Made of stainless steel, insulated trigger, EPDM rubber guards, Viton seals. Use for hot water requires particular caution. Connection: 1/2" BSP female. Working pressure: 24 bar. Flow rate: 75 l/min. Operating temperature: up to +95°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight plastic A gun for compressed air, intended for removing with surfaces all contamination: liquids, fine chips, filings itp. Flow adjustment by the degree of lever press. made with strength polyamide glass-fiber-reinforced. ergonomic shape and nie demanding use force operation the lever ensures comfort use. Ze regard na low mass and plastic construction particularly recommended for industry automotive, textile, electronic itp. A gun equipped is in standard nozzle o diameter hole 1.5 mm, replaceable, with a thread connection external M12x1.25. Instead of the standard nozzle, other nozzles can be mounted – see accessories for EWO guns. depending on connections we distinguish A gun terminated a plug EUROSTANDARD 7.2, fitting for hose o diameter 6 mm, 9 mm and 13 mm or a thread internal 1/4". Material: body - blue polyamide (PA6 GK30) glass-fiber-reinforced; sealing – NBR, PU. pressure Maximum: 10 bar. pressure operating: 2 ÷ 6 bar. Operating temperature: from -10°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAn MB cover, without a chain, for TW transfer couplings. Used for the VK (male) part, it constitutes a pressure-resistant cap. Material: aluminum. Operating temperature: from -20°C to +65°C (should take into account medium and Material sealing). gasket type TWF, Material the gasket: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCrimping press P20 NMS to basic stationary device for workshops, services and small plants, producing lines hydraulic o diameter internal for 1.1/2”, with intended for performing small production lines. Powered is motor electric with supply three-phase (400 V) o power 3 kW. control reaching diameter crimp takes place using optical indicator (indicator light LED), a po po jej reaching, jaws press alloy. setting diameter crimp adjustable is knob micrometric with accuracy settings 0.01 mm. All FINN-POWER crimping presses are adapted to work with interchangeable jaw sets (ordered separately). On example for range diameters crimp od 10 for 61 mm should order 12 sets jaws standard od FP-20-10 for FP-20-54. The machine P20X can equip additional in base or Hanger with sockets for storage jaws, in set with handle magnetic for ich quick replacement.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA 90° flange connection of compact design with a flange of a hole pitch diameter from 35 mm to 55 mm, with a metric male connection thread, 24° DIN 2353 socket. Used in hydraulic pump connections. Supplied as standard with a set of bolts, washers and an O-ring. Material: carbon steel, galvanized. Operating temperature: from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNipple with a thread internal and a thread external, for pressure gauge of standard connections pressure-gauge according to EN 837-1. allows assembly pressure gauge for socket o greater size. pressure gauge mounted for thread internal d1. connection to has character self-sealing – cone on bottom hole d1 presses in hole plug centring the connection pressure gauge. threads d1 and d2 are protected against unscrewing connections through applied special adhesive. intended for liquids and gases non-aggressive, for mounting pressure gauge, cocks and valves pressure-gauge and other accessories equipped in ten type the connection. Material: brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBolt for BANJO type HS with a metric or BSP thread, similar to DIN 7643. Material: carbon steel, galvanized.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble BANJO bolt with washer and female thread, type D10, for type R13, R14, D12, D17, D5, D6 fittings. Material: nickel-plated brass. Working pressure: 18 bar.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUnion with a thread internal BSP intended for use in pipe connections of industrial installations. sealing union: cone (metal-metal). Material: steel AISI 316. Working pressure: 10 bar. The given dimensions are indicative and may differ slightly depending on the manufacturer.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA MWSC silencer with a male thread, used in compressed-air systems to reduce the noise level. The noise reduction that can be achieved by installing a silencer, measured at a supply pressure of 5 bar, at a distance of 1m and at an angle of 45° from the silencer axis, is on average depending on size 35 dB. Material: brass nickel-plated, bronze sintered nickel-plated. Operating temperature: from -10°C to +80°C. pressure working: up to 12 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTee swivel, screw-in with a thread external cylindrical, series F type R 32 NSF. intended for industry food (e.g. for cold or hot water potable). no element plastic, coated coating nickel in special process chemical and seal made of Viton ensure high resistance to action detergents and other agents chemical. is suitable also for many applications in industry chemical, pharmaceutical, electronic and in medicine. Operating temperature: od -20°C up to +150°C. Working pressure: 16 bar. Vacuum: 0.99 bar. Material: brass nickel-plated. sealing: Viton (approved for contact with food through FDA). standards: NSF/ANSI 51, NSF/ANSI 61.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTee made of stainless steel, type 62400, with BSP female thread. Material: AISI 316L steel. Operating temperature: from -20°C to +225°C. Working pressure: 140 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, semi-transparent, reinforced a braid flexible hose with rubber silicone vulcanized platinum. intended for higher pressures. used in industry pharmaceutical, cosmetic, food, biotechnology, sterile lines filling, systems treatment water, production vaccines, bioreactors. is characterized exceptionally smooth surface inner prevents deposition and adhesion contamination inside hose and growth bacteria. facilitates to total cleaning and sterilization hose. smooth Layer inner reduces also resistance flow through hose. low extractability, nie toxicity, nie hemolyticity and nie pyrogenicity ensures total cleanliness liquids we sensitive use. minimal level loads biological (bioburden). meets requirements hygienic American FDA 21 CFR 177.2600, 3-A and USP Class VI. possible sterilization steam (30 min, 1 bar, 121°C), cleaning CIP and SIP installations, oxide ethylene or radiation (for 5 Mrad). Length of a full hose roll 15 m (od diameter internal 31.8 mm – 7.5 m). pressure working determined relative to pressure bursting at factor safety 1:4. Material: silicone (platinum). Maximum operating temperature: up to +160°C. temperature brittleness: -80°C. Hardness: 70° Shore (A). Density: 1.18 g/cm³. Note: The product is packaged in the Tubes International Clean Zone (CLEAN ROOM) in compliance with rigorous standards. Return of the product after opening the package is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA high-quality general-purpose worm-drive clamp intended for quick and easy fastening of industrial hoses, made entirely of AISI 316 stainless steel, recommended for use in the food, chemical, marine and similar industries. Manufactured in accordance with the requirements of DIN 3017 and the RoHS Directive 2002/95/EC. The ASFA-L clamp with a band width of 9 mm is recommended for standard applications. The unique worm mechanism in a compact housing and the cold-formed thread in the band, smooth on the inside, ensure a secure, repeated grip without damaging the hose surface. Material: AISI 316 stainless steel (W5).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA gasket for a railway nut, compatible only with nuts of KGW-type fittings. Material: NBR. Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, flexible, thick hose intended for discharge sawdust, chips, offcuts, bulk materials etc. Specially designed according to the requirements of the wood and furniture industry, it can also be used in other industries. compliant with the standard DIN 26057 Type 3. Antistatic and flame-retardant, it ensures a high level of work safety. thick wall and dense spiral reinforcing ensure high parameters pressure. very smooth inside, little compressible. flexible also in low temperatures. With very good abrasion resistance, also resistant to microbes and hydrolysis. Contains no halogen compounds or plasticisers. Resistant to oils and petrol. The optimal flow direction of the medium is marked with an arrow. The hose wall thickness is measured between the spiral. Assembly on connectors with bridge clamps (prawo-handed). Other diameters may be available on special order. Anti-electrostatic properties: permanently antistatic (in accordance with ISO 8031 resistance R 9 Ω, in accordance with the German technical regulations TRGS 727 (6.4.2.4) specific resistance R 8 Ωm, in accordance with directive 2014/34/EU (ATEX) it can be used in specified explosion-hazard zones - which should be preceded by a risk analysis). After effective two-sided earthing of the spiral, it can be treated as electrically conductive – in accordance with BGI 739-2 recommendations. Flame-retardant – in accordance with DIN 4102 class B1. Wall thickness measured between the spiral: 1.4 mm. Hose material: transparent polyether-polyurethane. Reinforcement: spiral with wire steel. Operating temperature: od -40°C up to +100°C (momentarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, very flexible hose used in systems, in which available frequent contact with water (high resistance to microorganisms and hydrolysis), detergents, solvents. Retains flexibility at low temperatures, is resistant to abrasion and kinking. The calibrated outer diameter allows use with push-in connectors. Hardness per Shore (A): 98°. Meets FDA requirements. Available in colour natural, black, blue, green, red. Hose material: polyether-polyurethane. pressure working: from 16 bar to 24 bar, depending on the diameter hose. Operating temperature: od -40°C up to +85°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible in wide the scope temperatures hose spiral, resistant to abrasion, sparks welding and hot chips metal. intended for pneumatic systems control, tools hand, robots industrial, etc. resistant to radiation UV and aging. terminated on both sides straight sections o length 100 mm and 500 mm and fitting with a male BSP threadT. Hardness per Shore (A): 98°. The stated total length is the maximum hose length after stretching. Hose material: flame-retardant polyurethane PUR. Working pressure: up to 13 bar (depending on the diameter hose). Operating temperature: od -40°C up to +70°C. standards: UL 94 VO (Layer outer). color black.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, smooth hose for oxygen, compliant with the standard EN ISO 3821. Do use with industrial equipment for welding autogenous, usually Together with red a hose acetylene. It can be used also for gas natural and air. Inner layer: black rubber SBR/EPDM. Reinforcement: PVA. Outer layer: blue EPDM rubber. Working pressure: 20 bar. Operating temperature: od -30°C up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong hose suction - delivery with layer inner with resistant chemical polyethylene o ultra-high weight molecular (UPE, UHMWPE). The inner layer is resistant to most acids and bases and many other aggressive chemicals (in elevated, ale nie very high temperatures), co makes, that hose is wide used in industry chemical and petrochemical. Layer inner with UPE is also compliant with requirements for hoses food, free of phthalates and polycyclic carbon aromatic (PAH), is characterized also low a coefficient friction during flow and prevents deposition medium na walls. This significantly facilitates cleaning and allows use also in the cosmetic, pharmaceutical and food industry. Reinforcement cord synthetic and spiral steel, built-in cable copper for discharge charges electrostatic. Layer outer with resistant chemical rubber EPDM, resistant na abrasion, ozone and conditions atmospheric. compliant with requirements EN 12115:11 (type M, resistance between fitting the line R ≤ 100 Ω, guaranteed for lines o length for 40 m). standards and requirements : hoses chemical: EN 12115:2011. industry food, contact with food (Layer inner): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU (simulant fluids A, B, D2), FDA 21 CFR 177.1520, BfR III. Confirmation of resistance and application conditions requires contact with Tubes International, in particular for temperatures above 50°C. Inner layer: white cream polyethylene UPE. Reinforcement: synthetic cord, steel spiral. Outer layer: black rubber EPDM. pressure working: 16 bar. temperature use: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight, flexible, hose suction-delivery o internal layer with resistant to abrasion and oil polyurethane, with densely arranged steel spiral reinforcing for increasing pressure working and resistance to vacuum. intended for air, liquids, light chemicals, in systems pneumatic, hydraulic and for conveying substances solid. smooth surface inner reduces losses flow and ensures ease cleaning. transparent wall allows on visual control of the flow. Reinforcement dense spiral with wire steel ensures very good resistance to vacuum and kinking hose and small radius bends. W use general-industrial It can be used: for water, light chemicals and other liquids based on fat, oils and hydrocarbons (should take into account resistance chemical polyurethane) and for air, for vacuum conveying dusts, powders, granulates and other abrasive substances bulk (should then take into account abrasion resistance medium and any problem electricity static). It can be used in industry food (tam, where acceptable are requirements American FDA 21 CFR 177.2600 e, f) for liquid substances food for food hydrated („e”) and greasy („f”). Inner layer: transparent polyurethane. Reinforcement: steel spiral. Outer layer: transparent PVC. Working pressure at a temperature of 20°C: from 12 bar to 20 bar - depending on the diameter hose. Operating temperature: from -20°C to +90°C. As the working temperature rises, the hose's working pressure value decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose Hyperline FX SS RC BLACK to light, flexible hose PTFE, has additional layer external made with black, antistatic and flame-retardant rubber EPDM, meeting (rubber) requirements for vehicles railway EN 45545. ensures to additional cover braid and hose against damage and easy cleaning hose. Ze regard na its properties recommended for applications in industry and vehicles mechanical. hose can be delivered without ends, jak and in the molds complete lines, gorowych for mounting. Material hose: inside smooth, externally Serrated PTFE (teflon). Reinforcement: single braid of steel AISI 304 with additional layer protective with rubber EPDM. pressure working: from 50 bar to 110 bar - depending on diameter hose. temperature use: from -40°C to +140°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose delivery for low-pressure parts installations hydraulics power, compliant with the standard SAE 100 R6 and ISO 4079 R6. intended primarily for liquids hydraulic based on oil mineral and some synthetic liquids hydraulic. can be also used for liquids hydraulic based on water and for water and air at limiting temperatures up to +70°C (use for air can require microperforation layer outer). is suitable for many liquid products industry petrochemical: oils mineral and synthetic, oil drive and heating, glycol ethylene and other. Not recommended for gasoline and oils based on esters, not is suitable for hydrocarbons aromatic. Layer inner with black, smooth rubber synthetic. Reinforcement a braid textile. Layer outer with black rubber synthetic, resistant to abrasion, oil, ozone and conditions atmospheric. Inner layer: black synthetic rubber. Reinforcement: single textile braid. Outer layer: black synthetic rubber. Working pressure: from 12 bar to 28 bar - depending on the diameter hose. Operating temperature: od -40°C up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and light hose delivery, o wall small wall thickness, almost flat at rest, intended for use in heavy conditions. used m.in. for conveying water industrial and sewage, for pumps immersion, systems dewatering and irrigation, mobile irrigation. resistant to abrasion, conditions atmospheric and ozone. design hose allows its easy winding po use. assembly using bands or straps. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black synthetic rubber. Reinforcement: cord polyester. Outer layer: black synthetic rubber. Working pressure: 10 bar. Operating temperature: od -25°C up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA two-part insert of a DIN 3015 type 301 clamp, made in accordance with the DIN 3015 standard. As standard, it has a profiled (grooved) surface of the pipe hole. Material insert: self-extinguishing polyamide. Operating temperature: from -40°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug quick coupling Hansen Beverage with valve and connection with a thread external NPT. The couplings are available in two versions: for gases type HB-2KG... and for liquids type HB-2KL.... These versions are not interchangeable with each other (different plug diameter), which allows avoiding mistakes in connection. Recognizing the version is very easy. For gas couplings, the identification ring on the socket is white, and the hexagon on the plug has a notch. For liquid couplings, the identification ring on the socket is black, and the hexagon on the plug has no notch. pressure working: 15 bar. Operating temperature: up to +130°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug quick coupling DN11.8 with a thread external facilitating fast connection spray gun for water with a hose or with other accessories for washing. Material: steel AISI 303/304L. Working pressure: 200 bar. Operating temperature: up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPlug WEO with fittings for hose for use in hydraulic systems where there is not enough space, to install line in the traditional way. Po connection plug has freedom of movement in the socket, co zapobiega screwing lines in trakcie installation. intended for hoses type 1SN, 2SN, 1SC, 2SC. Working pressure: 350 bar (for a hose size up to 3/4"), 250 bar (for a hose size 1"). Material: case-hardened steel. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe RFL L type B throttle check valve (threaded connection with an O-ring on one side and a push-in connection on the other) regulates the airflow in both directions. Working pressure: 10 bar. Operating temperature: from -20°C to +60°C. Medium: filtered compressed air, oiled or non-oiled.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA high-quality three-way ball valve "L" type BK3L with a thread internal BSP, intended for high-pressure installations hydraulic. Material: steel (body, ball, stem). Seals: POM (ball), NBR (stem). Operating temperature: from -40°C to +100°C (POM); from -20°C to +100°C (NBR).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCoupling IBC with a thread internal trapezoidal compliant with the DIN EN 12713 standard and of coupling type CAMLOCK D (socket). The trapezoidal threads that the IBC couplings are fitted with as standard match 100% the threads in the IBC containers of various manufacturers. Material: polypropylene. gasket: low-density polyethylene (LDPE). Working pressure: up to 7 bar. Operating temperature: from -10°C to +70°C (momentarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° angled fitting, type B6, with a cutting ring, designed for connecting copper pipes and plastic hoses. When connecting to hoses, the use of reinforcing sleeves (B12) is recommended. Material: nickel-plated brass. Working pressure: 60 bar.
