Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, semi-transparent smooth-walled PTFE hose with excellent chemical resistance. Designed for low-pressure installations, chemicals, paints, adhesives, liquid and gaseous fuels, oils, lubricants, air, gases, water, steam, and water-based fluids. Used in all types of industry. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. Can also be used as mechanical guidance for hoses or rods due to the low friction coefficient and self-lubricating properties of Teflon. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 4:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Hose material: smooth PTFE (Teflon). Shore hardness (D): 58. Operating temperature: from -200°C to +260°C. Working pressure: from 2.3 bar to 10.8 bar - depending on the hose diameter.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe HYPERLINE SB (HYDRAFLON) hose features an inner layer made of high-quality seamless PTFE, ensuring minimal porosity, maximum flexibility, and resistance to vibrations. The braid is made from heat-treated AISI 304 stainless steel wire with a tensile strength of 1700 MPa. It is used for the transmission of chemicals, food substances, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. The HYPERLINE SB hose is a version of the SMOOTHBORE hose with a medium wall thickness and an internal diameter adapted to standard hydraulic fittings; installation is done using standard straight clamp jaws. In cases where static electricity hazards are identified (risk of charge generation and accumulation), HYPERLINE SB hoses in the antistatic AS version should be used. The antistatic Teflon in the AS version is black (contains appropriately dispersed graphite in PTFE) and has a resistance R <10^8 Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. At operating temperatures above +130°C, the maximum working pressure should be reduced by 0.75% for each 1°C increase in temperature. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: single braid of AISI 304 steel. Working pressure: from 80 bar to 350 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, semi-transparent smooth-walled PTFE hose with excellent chemical resistance. Designed for low-pressure installations of chemicals, paints, fuels, oils, greases, air, gases, water, steam, and water-based fluids – in all types of industry. As it is chemically inert and does not contain components that could leach into the internal medium, it can be used for food substances. Compliant with FDA 21 CFR 177.1550, EU 10/2011, EC 1935/2004, and Italian D.M. 174 06/04/2004. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. It can also be used as mechanical guidance for hoses or rods due to the low friction coefficient and self-lubricating properties of Teflon. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 3:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Hose material: PTFE (Teflon). Operating temperature: from -60°C to +260°C. Working pressure: from 3 bar to 56 bar - depending on the diameter and wall thickness of the hose.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight transparent smooth-walled hose made of natural (non-regenerated) fluoropolymer FEP (fluorinated ethylene propylene), a material with properties similar to PTFE. The hose features excellent chemical resistance, dimensional and shape thermal stability, and a smooth internal and external surface. Good transparency of the hose allows for easy observation of fluid level or flow. UV resistant. Designed for low-pressure installations of aggressive chemicals or where high purity and chemical inertness of the hose material are required. Commonly used in laboratories, chemical and pharmaceutical industries. Due to its excellent insulating properties, it is used in the electronics and semiconductor industries. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 4:1. Hose material: FEP. Shore hardness (D) 55. Operating temperature: from -200°C to +206°C. Working pressure: from 4.25 bar to 13 bar - depending on the hose diameter.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight smooth-walled hose made of PTFE with excellent chemical resistance in various color versions. Made from high-quality PTFE with added dye (material compliant with FDA). Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Application for high-quality plug connections is possible. Safety factor n=4:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Material: PTFE (Teflon), dyed. Shore hardness (D): 60. Working pressure: from 5.5 to 20 bar. Operating temperature: from -200°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon tube of the hose is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The braid is made of annealed AISI 304 stainless steel wire with a high tensile strength of 1700 N/mm², with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. Due to the unique properties of PTFE (wide operating temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. In cases where there is a risk of static electricity (danger of charge generation and accumulation), SMOOTHBORE hoses made of antistatic Teflon should be used – the antistatic version AS. The antistatic Teflon of version AS is black (contains appropriately distributed carbon in PTFE) and has a resistance R <10⁸ Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. The safety factor is 3:1; if a factor of 4:1 is required (e.g., according to EN 16643), the values should be multiplied by 0.75. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C above this temperature. For example, at a temperature of 170ºC, the maximum working pressure for the hose AF-SWSB-06 is: 240 bar – (170°C-130°C) x 0.75 = 240 bar – 30% = 168 bar. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: single braid of AISI 304 steel. Working pressure: from 55 bar to 240 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon tube of the hose is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The heavy-duty HW version is recommended for harsher working conditions, gases (up to 100 bar), and applications where cyclic temperature changes occur. The braid is made of annealed AISI 304 stainless steel wire with a high tensile strength of 1700 N/mm², with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. Due to the unique properties of PTFE (wide temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. In cases where there is a risk of static electricity (danger of charge generation and accumulation), SMOOTHBORE hoses made of antistatic Teflon should be used – the antistatic version AS. The antistatic Teflon of version AS is black (contains appropriately distributed carbon in PTFE) and has a resistance R <10⁸ Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. The safety factor is 3:1; if a 4:1 factor is required (e.g., according to EN 16643), the values should be multiplied by 0.75. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C above this temperature. For example, at a temperature of 170°C, the maximum working pressure for hose AF-HWSB-06 is: 260 bar – (170°C-130°C) x 0.75 = 260 bar – 30% = 182 bar. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: single braid of AISI 304 steel. Working pressure: from 55 bar to 240 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecial high-pressure version of the SMOOTHBORE Teflon hose with a thickened wall made of specially processed Teflon (reduced microporosity) for applications with high-pressure gases in a double braid (aramid and steel braid) and with an outer layer of Hytrel. The outer layer of Hytrel is available in four colors: black, blue, green, and red, to indicate the hose's intended use for a specific type of gas. When both HPG inner layer and AS antistatic layer are required, the HPG/AS hose (red color) can be used, featuring an additional thin AS antistatic layer inside the primary inner layer of natural HPG Teflon. Installation: use AF-TL series fittings and sleeves... Hose material: smooth PTFE (Teflon) HPG. Reinforcement: aramid braid + AISI 304 steel braid. Outer layer: microperforated Hytrel (colored polyester). Working pressure: 300 bar. Operating temperature: from -50°C to +70°C (due to the outer layer of Hytrel).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight smooth-walled PTFE hose with antistatic properties and excellent chemical resistance. The conductivity and dissipation of electric charges are achieved by the addition of up to 2.5% carbon black - PTFE AS. This allows for a reduction in the resistance of the hose material and meets the requirements of the EN12115 standard, which requires resistance between the ends of the hose to be less than 106 Ω/m. The hose is particularly intended for aggressive chemically non-conductive substances, such as organic solvents, whose flow in a standard Teflon hose can cause the accumulation of electric charges and associated hazards. High purity and distribution of the carbon additive in PTFE ensure compliance with FDA 21 CFR 178.3297 regarding materials approved for temporary contact with food. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). The use of high-quality plug couplings is possible. Safety factor n=4:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Material: antistatic PTFE (Teflon), black. Shore hardness (D): 60. Working pressure: from 5.5 to 12 bar. Operating temperature: from -200°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight transparent smooth-walled hose made of natural (non-regenerated) fluoropolymer PFA (perfluoroalkoxy), a material with properties similar to PTFE. The hose features excellent chemical resistance, dimensional and shape thermal stability, a very smooth, micropore-free internal and external surface, high pressure resistance, and crack resistance due to excessive stress. Good transparency of the hose allows for easy observation of level or flow. UV resistant. Designed for low-pressure installations of aggressive chemicals or when high purity and chemical inertness of the hose material are required. Commonly used in laboratories, chemical and pharmaceutical industries. Due to its excellent insulating properties (dielectric strength 3 to 4 times greater than PTFE), it is used in the electronics and semiconductor industries. The hose is not antistatic (does not dissipate electric charges for non-conductive substances). Not recommended for pneumatic plug connections. Flame retardant (UL94 V-0) and with a high oxygen index (LOI). Safety factor n = 4:1. The burst and working pressure of the hose decreases at operating temperatures above 20°C and is dependent on its height. Hose material: PFA. Shore hardness (D) 60. Operating temperature: from -200°C to +260°C. Working pressure: from 7 bar to 19.5 bar - depending on the diameter and wall thickness of the hose.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSmoothbore Teflon hose version with reinforced wall made of specially processed Teflon (reduced microporosity) for use with high-pressure gases and other penetrating substances, in double steel braid. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C increase in temperature. Installation: use AF-TL series fittings and sleeves... Hose material: smooth PTFE. Reinforcement: double braid of 304 steel. Working pressure: from 180 bar to 225 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCHEMFLUOR TH hose is a flexible Teflon hose designed for high-pressure hydraulic, pneumatic, and gas installations. The inner layer made of conductive Teflon prevents the accumulation of electrostatic charges. Hose material: black, conductive PTFE. Reinforcement: AISI 304 steel braid. Operating temperature: from -50°C to +200°C. Working pressure: 345 bar. Burst pressure at 20°C: 1100 bar. Burst pressure at 200°C: 820 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon tube of the hose is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The heavy-duty HW version is recommended for harsher working conditions, gases (up to 100 bar), and applications where there are cyclic temperature changes. The braid is made of annealed AISI 304 stainless steel wire with a high tensile strength of 1700 N/mm², with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. Due to the unique properties of PTFE (wide temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. In cases where there is a risk of static electricity (danger of charge generation and accumulation), SMOOTHBORE hoses made of antistatic Teflon should be used – the antistatic version AS. The antistatic Teflon of version AS is black (contains appropriately distributed carbon in PTFE) and has a resistance R <10⁸ Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. The safety factor is 3:1; if a 4:1 factor is required (e.g., according to EN 16643), the values should be multiplied by 0.75. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C above this temperature. For example, at a temperature of 170°C, the maximum working pressure for the hose AF-HWDB-10 is: 240 bar – (170°C-130°C) x 0.75 = 240 bar – 30% = 168 bar. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: double braid of AISI 304 steel. Working pressure: from 40 bar to 350 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon tube of the hose is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The braid is made of annealed AISI 304 stainless steel wire with a high tensile strength of 1700 N/mm², with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. A double braid should be used for higher pressures and where there is (within permissible limits) greater bending or kinking of the hose. Due to the unique properties of PTFE (wide operating temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. In cases where there is a risk of static electricity (danger of charge generation and accumulation), SMOOTHBORE hoses made of antistatic Teflon should be used – the antistatic version AS. The antistatic Teflon of version AS is black (contains appropriately distributed carbon in PTFE) and has a resistance of R<10^8 Ω (according to ISO 8031 annex A). This ensures the dissipation and dispersion of electric charges. The safety factor is 3:1; if a factor of 4:1 is required (e.g., according to EN 16643), the values should be multiplied by 0.75. At operating temperatures above +130°C, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1°C above this temperature. For example, at a temperature of 170°C, the maximum working pressure for hose AF-SWDB-08 is: 250 bar – (170°C-130°C) x 0.75 = 250 bar – 30% = 175 bar. The value "Wall thickness [mm]" provided in the Technical Data refers to the PTFE layer. Hose material: smooth PTFE (Teflon). Reinforcement: double braid of AISI 304 steel. Working pressure: from 70 bar to 360 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe hose is made of a smooth, seamless PTFE tube. The Teflon hose tube is extruded under strictly defined and controlled conditions, ensuring its highest quality, minimal porosity, and maximum flexibility and elasticity achievable for a smooth PTFE hose. The braid is made of annealed AISI 316 steel wire, with a strictly controlled angle of arrangement and tension of the braid wire bundles, resulting in minimal length changes of the hose under high pressure. Due to the unique properties of PTFE (wide operating temperature range, resistance to most substances and chemical compounds, negligible surface adhesion), the SMOOTHBORE hose is perfectly suited for the transfer of chemicals, foodstuffs, fuels, oils, paints, solvents, adhesives, dyes, detergents, steam, etc. - as well as for classic high-pressure hydraulic oil installations. Safety factor 3:1; if a 4:1 factor is required (e.g., according to EN 16643), values should be multiplied by 0.75. At operating temperatures above +130ºC, the maximum working pressure specified in the parameters should be reduced by 0.75% for each 1ºC above this temperature. For example, at a temperature of 170ºC, the maximum working pressure for the hose AF-SWSB-316-06 is: 240 bar – (170ºC-130ºC) x 0.75 = 240 bar – 30% = 168 bar. Hose material: smooth PTFE (Teflon). Reinforcement: single braid of AISI 316 steel. Working pressure: from 80 bar to 240 bar - depending on the hose diameter. Operating temperature: from -70°C to +260°C.
