Our products
Select options This product has multiple variants. The options may be chosen on the product page / DetailsBand-It® Standard tape, made of AISI 304 steel. Standard is the basic clamping system using tape in rolls, formed into bands on hoses of any diameter (a double loop of tape is recommended). Separate clips with "noses" must be purchased to secure the end of the tape after bending. Installation using tools BD-C07599, BD-C00189, BD-C00399. Length: 30.5 m.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCover gasket MB (for tank truck connections) type TWF (for 4" connection, use O-ring gasket type TWO). Material: viton (FPM). Temperature range (approximate): from -20°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible five-layer hose for compressed air. Lightweight, very flexible even at low temperatures, resistant to elongation. Antistatic (R <106 Ω/m, EN ISO 8031), resistant to elevated ambient temperatures, suitable for disinfection. Specifically designed for breathing apparatus in accordance with EN 14593 and EN 14594 standards. Used in the paint industry, petrochemical industry, construction, and nuclear energy. Available on special order in DN6 and DN10 in green color. Inner layer: black, antistatic PVC. Reinforcement: polyester braid. Outer layer: blue PVC. Working pressure: 15 bar (6 bar at 70°C). Operating temperature: from -20°C to +70°C (temporarily up to +80°C), working pressure dependent on temperature.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGeneral-purpose hydraulic hose with reduced outer diameter and weight, and increased flexibility. Complies with standards: EN 857 1SC, EN 45545-2. Inner layer: black synthetic rubber. Reinforcement: single steel braid. Outer layer: black, flame-retardant synthetic rubber. Operating temperature: from -40°C to +100°C (temporarily up to +125°C). For water and air, maximum operating temperature +70°C. For air above 17 bar, micro-perforation of the outer layer is required.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong, thick, flexible hose designed for suction and transport of granules and other bulk materials. Intended for use in various types of industry. Used for plastic granules, insulation materials, waste, sand, and other construction materials. Quite flexible, low compressibility, smooth inside, elastic even at low temperatures. Good abrasion resistance, resistant to microbes and hydrolysis. Non-toxic, free from halogen compounds and plasticizers. Resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed). Other diameters may be available. In addition to the standard version P7 M PU AE, the hose is available in the P7 M PU EL version, which is electrically conductive (R ≤104 Ω), compliant with ATEX 2014/34/EU, TRBS 2153, and for suction also with TRGS 727, it can be used in explosion hazard zones after conducting a risk assessment. Hose material: polyester-polyurethane. Wall thickness measured between the spiral: 1.4 mm. Reinforcement: spiral with steel wire. Operating temperature: from -40°C to +100°C (temporarily up to +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose with conductive fibers in the braid (R<3x104 Ω/m) designed for solvents, paints, isocyanates, polyols, water-based fluids. Standards: ISO 8031, SAE 100R7, EN855-R7, ISO 3949-R7. Inner layer: polyamide. Reinforcement: double polyester braid with conductive fibers. Outer layer: microperforated polyurethane. Operating temperature: from -40°C to +100°C (for water and air up to +70°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible hose designed for pressure cleaning of sewage systems. It features high abrasion resistance. Supplied as a complete hose with fittings. The hose has a red marker at a distance of 0.5 m from the end. Other fittings and lengths available - contact Tubes International. Inner layer: black, smooth synthetic rubber. Reinforcement: single steel braid. Outer layer: black, smooth synthetic rubber. Working pressure: 300 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery flexible hose designed for the transfer of food, pharmaceutical, and cosmetic substances: water, fruit juices, beer, wine, vinegar, alcohols up to 96% concentration, milk and its derivatives, creams, soaps, aromatic substances, pigments, and others. Resistant to fats and oils in standard usage conditions. Good chemical resistance to light chemicals – solutions of acids and bases. Extruded, completely smooth inner and outer layers of the hose facilitate flow and cleaning. The hose material is non-vulcanized, clean (contains no vulcanization additives), resistant to hydrolysis, does not promote bacterial growth, has low porosity and low permeability. Completely neutral in taste and odor, does not alter the organoleptic properties of the medium. Resistant to aging, weather conditions, and UV radiation. Hose cleaning, disinfection, or sterilization should be carried out strictly according to the recommendations provided in the catalog sheet below. Cleaning by SIP method is not recommended as it significantly shortens the service life. Use for high-proof alcohol (its vapors or other flammable substances) requires consideration of hazards related to static electricity. Standards and requirements: 1) Food industry, contact with food: compliant with European requirements 1935/2004/EC and 10/2011/EU (simulants A, B, C, D1, D2), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 "e". 2) Pharmaceutical industry USP CLASS VI. Hose material: transparent TPE-S. Reinforcement: polyester braid. Working pressure: from 7 bar to 12 bar, depending on the hose diameter. Operating temperature: -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-part insert of DIN 3015 type 201 clamp made according to DIN 3015 standard. It typically features a profiled (grooved) surface for the pipe opening. Insert material: green polypropylene. Operating temperature: from -30°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° quick coupling plug with hose end with valve and without shut-off valve, intended for water, chemical, pneumatic installations, etc. Compared to traditional massive couplings with balls and protective sleeves, it has a very low weight. The highly efficient valve allows for high flow rates and minimal leakage. This coupling also allows for slight rotations of the connected hose, preventing twisting and accidental disconnection of the coupling. Applications: chemical photographic processes, battery and accumulator filling installations, sprayers, pneumatic installations, and non-freezing liquids, etc. Length L [mm] - total length. Material: polypropylene. Sealing: EPDM o-ring. Working pressure: up to 4.2 bar. Operating temperature: from 0°C to +71°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality quick-connect water plug NiTO 3/4" with hose end. Material: chrome-plated brass. Working pressure: up to 25 bar. Operating temperature: up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBPS quick coupling plug without valve with internal BSP thread for lances, guns, and cleaning devices. Material: carbon steel, galvanized. Working pressure: 3100 bar. Operating temperature: +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLight and flexible, popular general-purpose PVC hose. Used for water, air, light chemicals in agriculture, horticulture, industry, and for domestic use. Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: green transparent PVC. Working pressure at 20°C: from 10 bar to 17 bar - depending on the hose diameter. Operating temperature: from -5°C to +60°C. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLock intended for the production of hose ties. Lock for tape width of 8 mm or 14 mm. Lock material: AISI 304 or AISI 430 steel. Screw material: galvanized steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsEnd cap for CAMLOCK DP coupling made according to American military standard MIL-C-27487 (A-A-59326). Working pressure: up to 10 bar, depending on coupling size. Material: aluminum.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsT-shaped ORFS tee fitting with external UNF thread (O-ring seal in the groove of the flat face). Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-part adapter for high-pressure cleaning devices with metric connection M22x1.5. Material: brass. Working pressure: up to 280 bar. Operating temperature: up to +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAutomatic drum rewinder MINI used in the food industry, chemical industry, manufacturing plants, repair workshops, dairies, slaughterhouses, farms, gas stations, sewage treatment plants, etc. Equipped with a spring mechanism that causes the hose to retract with a light pull. Supplied with a PVC hose intended for water and air. Material: PVC. Operating temperature: from -10°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe SAFLOK® D socket with BSP internal thread is a variant of the CAMLOCK coupling with protection against accidental disconnection. The protection consists of spring-loaded latches located in the levers of the socket. During the closing of the lever, the latches automatically lock. Unlocking when opening requires pulling back the latches. The SAFLOK® D socket is compatible with other CAMLOCK couplings made according to the MIL-C-27487 standard. Spare parts are available: levers with latches and pins. The coupling size 1/2" has a thread of 1/2" and a socket of 3/4". Material: AISI 316 steel. Sealing: NBR. Working pressure: 20 bar (1/2" ÷ 2"), 10 bar (2.1/2" ÷ 4"). Operating temperature: from -40°C to +93°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsEAR CLIP clamp ring with 1 ear for mounting various types of low-pressure hoses reinforced with a braid or without reinforcement. Easy and quick installation using specially designed pliers. Rounded edges inside the ring protect the hose from damage. Material: galvanized carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDesigned for the transmission of LPG (Liquid Petroleum Gas) in accordance with EN 589 standards in tankers, fuel installations, and fuel stations. Certified by Germanischer Lloyd. Also available with ASA 300 flanges. Marked on the single sleeve with an orange stripe. Inner layer: conductive NBR rubber. Reinforcement: nylon cord. Outer layer: conductive CR rubber. Flanges: galvanized carbon steel. Operating temperature: from -20°C to +90°C (temporarily +100°C depending on the medium).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAir vent plug with a check valve and O-ring mounted at the top of the tank. Opens during pressure increase in the tank (oil turbulence). Prevents contamination from entering the system during hydraulic oil suction. Check valve opening pressure: 0.15 ÷ 0.3 bar. Material: aluminum (body), steel (cover), guarnital (fiber washer). Operating temperature: from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMounting bracket (angle bracket) intended for ISO 15552 actuator series STD, series 3, "two flat", with a diameter from 32 mm to 125 mm, model A. Included: 2 screws. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNon-freezing high-pressure water gun AURA AF LP for industrial applications. Suitable for hot and cold water. The lever mechanism does not require the operator to exert significant force, resulting in comfortable and pleasant operation. The outlet part is finished with a 1/4" BSP internal thread. The gun is also available with a swivel connection for installation. Housing material: high-strength plastic. Working pressure: up to 180 bar. Maximum pressure: 220 bar. Flow rate: 30 l/min. Leakage only below 10 bar. Operating temperature: up to +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, highly flexible, unreinforced hose produced in the United Kingdom. Designed for non-pressurized (or very low-pressure) transmission of air, water, and liquids in general industrial applications, for light chemicals (e.g., diluted acids and bases), in laboratory applications, for level indicators, and as protection for pipes, conduits, hoses, etc. The hose material is free from phthalates, silicone, and cadmium, compliant with REACH, RoHS, and WEEE regulations. According to EU regulations, use for food products is possible after conducting the required migration tests using appropriate model fluids simulating the specific type of food (the material used for hose production complies with the requirements of 10/2011/EU and FDA 21). The hose material is self-extinguishing according to UL94-V2 and UL94-HB (at a thickness of 3 mm). The stated working pressure is an indicative value of the recommended working pressure with a safety factor of 5:1. Hose material: transparent PVC. Operating temperature: from -20°C to +55°C (temporarily up to +65°C, working pressure dependent on temperature).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDIN 3015 double clamp type 301 (with top plate) designed for quick, easy, durable, and aesthetic mounting of pipes, hoses, and hoses in various industrial sectors, in ground and marine installations. Manufactured according to DIN 3015 standard. The clamp is mounted to the structure using welding of the clamp base (there is an option for bolting or mounting on a rail). The clamp typically features a profiled (grooved) surface for the pipe opening. In addition to standard metal components, extended plates, rails, and screws for mounting clamp sets can be ordered. Selection of components should be consulted with TUBES INTERNATIONAL®. Clamp material: self-extinguishing polyamide. Clamp material: rubber. Screw material: galvanized steel. Plate material: galvanized steel. Base material: carbon steel. Operating temperature: from -40° to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal gun for air, water, and non-explosive fluids. Designed primarily for blowing out contaminants, including in hard-to-reach places. Characterized by high blowing force, with adjustable flow size. Lightweight construction, ergonomic shape of the gun, and low trigger pull force ensure high work comfort. The gun is standardly equipped with a socket with a 1/4" BSP or 1/4" NPT thread. This model is available with a 90 mm bent Star-Tip nozzle, interchangeable. Sound level below 85 dB, in accordance with the European Machinery Directive art. 1.5.8. Compliant with OSHA standard 1-13.1. (European Agency for Safety and Health at Work). A wide range of additional accessories allows for adaptation to specific application requirements. Material: POM (body), brass (valve). Sealing: NBR. Working pressure: 16 bar. Burst pressure: 64 bar. Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCounter nut for use in EE type cast iron joints used in piping connections of industrial installations. Material: ductile iron. Operating temperature: up to +300°C. Working pressure: 25 bar (up to +120°C), 20 bar (up to +300°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsIndustrial, high-quality, ergonomic NITO II water gun. Handle separated from the hot water flow path, ensuring operator comfort. Internal parts made of aluminum, brass, and stainless steel. Housing made of high-strength Orgalloy plastic resistant to impact. The set includes: NiTO SC plug with disconnection protection 3/4", NiTO SC socket with disconnection protection 3/4", NiTO plug 3/4", NiTO socket 3/4", and three hose clamps. Quick couplings made of chrome-plated brass, hose clamps made of stainless steel. Seals: EPDM / HBR. Features smooth flow regulation and trigger lock. Replaceable outlet nozzles. Working pressure: 25 bar. Flow rate: 20 ÷ 60 l/min (5 bar) depending on the installed nozzle. Flow with standard nozzle: 40 l/min. Operating temperature: up to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe connection for the tap is available with a 1/2", 3/4", or 1" internal thread, allowing the attachment of a garden hose with a mounted quick coupling to a source of running water. Material: PVC. Working pressure: up to 6 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight ORFS fitting with external metric thread (rectangular cross-section elastomer seal), type EVGE-ME. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMonoblock sliding valve distributor YFM35 controlled by a manual lever with centering springs. Designed for hydraulic systems of cranes, lifts, construction machinery, agricultural equipment, etc. Standardly equipped with a type C safety valve (set to 140 bar) and type 1 sliders. Material: cast iron (body), hardened steel (sliders). Sealing: NBR. Maximum working pressure: 315 bar. Maximum return pressure: 25 bar. Operating temperature: from -20°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBand-It® Standard system tape, made of AISI 316 steel. Standard is the basic clamping system using roll tape, formed into bands on hoses of any diameter (a double loop of tape is recommended). Separate clips with "ears" must be purchased to secure the end of the tape after bending. Installation using tools BD-C07599, BD-C00189, BD-C00399. Length: 30.5 m.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsO-ring seal type TWO for use in 4" tank truck connections - MB, MKV, and MK. Material: viton (FPM). Temperature range (approximate): from -20°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStandard gasket for the female part (socket) of the CAMLOCK coupling. Material: NBR. Operating temperature: from -40°C to +93°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAnaerobic thread sealant. Sealing of hydraulic and pneumatic systems. Medium viscosity, medium strength – possible disassembly. Maximum gap 0.15 mm. Color: brown. Operating temperature: from -60°C to +150°C. Packaging type "pen" with a capacity of: 20 and 50 ml.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGeneral-purpose hydraulic hose with increased flexibility (bending radius 50% better than standard). Enhanced hose lifespan compared to standard confirmed by a test of 1,000,000 impulse cycles. Outer layer flame-resistant (MSHA). Standards: EN 856 R13, SAE 100 R13, ISO 3862-1 R13. Inner layer: black, oil-resistant synthetic rubber. Reinforcement: four layers of steel wire (six for DN 32 ÷ DN 38). Outer layer: black, oil-resistant synthetic rubber. Working pressure: from 350 bar to 380 bar depending on hose diameter. Operating temperature: from -40°C to +121°C (temporarily +125°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery strong and thick, flexible hose designed for suction and transport of abrasive bulk materials, granules, sand, gravel, pebbles, agricultural substrate. Used for loading and unloading silos, vehicles, and suction excavators, transloading from tankers, etc. Thick wall and fairly dense reinforcing spiral provide high resistance to pressure and vacuum. Smooth inside, non-compressible, quite flexible (r=2.5xD), elastic even at low temperatures. Hose with good abrasion resistance, also resistant to oils and gasoline. Installation on couplings with bridge clamps (right-handed) or special installation on industrial ends, e.g., flanges. Other diameters may be available upon special request. Versions: P3 SV PU – with polyester – polyurethane, very abrasion resistant; P3 SV PU AE - version with polyether – polyurethane, abrasion resistant, resistant to microbes and hydrolysis, compliant with European regulations 1935/2004/EC and 10/2011/EU (simulant E), 2023/2006/EC (GMP) and American FDA 21 CFR 177.2600 and 178.2010. Suitable for temporary contact with food during the transfer of dry, bulk, non-fatty substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Hose material: transparent polyester-polyurethane (P3 SV PU), polyether – polyurethane (P3 SV PU AE). Wall thickness measured between the spiral: 2.5 mm. Reinforcement: spiral made of steel wire. Operating temperature: from -40°C to +100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible suction hose designed for sewage and water. Corrugated on the outside, nearly smooth on the inside. The special profile makes the hose resistant to vacuum and kinking (it returns to its shape). As a polyethylene hose, it has very good chemical resistance and resistance to biological corrosion (rotting, decay). It remains flexible at low temperatures. The hose is commonly used for emptying septic tanks and portable toilets, in construction, tourist facilities, marinas, and airports. Hose material: yellow polyethylene profile (PE). Reinforcement: black polyethylene profile (PE). Vacuum: 0.95 bar (for diameter 51mm ÷ 76mm); 0.85 bar (for diameter 102mm). Operating temperature: from -40°C to +60°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose designed for solvents, paints, isocyanates, polyols, and water-based fluids. Also available in a microperforated version (for gases and air), marked with the letters "MP" at the end of the index. Inner layer: polyamide. Reinforcement: steel braid. Outer layer: polyurethane. Working pressure: from 70 bar to 375 bar - depending on the diameter. Operating temperature: from -40°C to +100°C (for water and air up to +70°C).
