Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsTwo-way branching module GA series G with internal BSP thread, used for air intake from any location of the FRL station. Supply pressure: up to 10 bar. Operating temperature: up to +70°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPA branching module, SKILLAIR® series, with end plates, is used for air intake from the FRL station at any stage of its preparation, regardless of the installation location. Size: 100, 200, 300. Supply pressure: up to 15 bar (13 bar - size 200, 300). Operating temperature: up to +50°C. Connection: BSP thread 1/4" ÷ 1".
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe distribution module is used when there is a need to draw air from the FRL Newdeal unit at any stage of its preparation, e.g., reduced air, oil-free air, or supply air. Size: 1/4", 3/8", 1/2", 3/4", 1". Connection: BSP female thread 1/8" for 1/4", BSP female thread 1/4" for 3/8" to 1/2", BSP female thread 1/2" for 3/4" to 1". Working pressure: up to 18 bar. Operating temperature: from -10°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBranching module - coupling mounted between two any SYNTESI® modules, used for independent air intake. Version 2 - two-way, has two connections (upper and lower). Size: SY1, SY2. Operating pressure and temperature: dependent on the SYNTESI® modules it is connected to. Flow: 1550 l/min - 1/8" (SY1), 7000 l/min - 3/8" (SY2), (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe branching module is a coupling mounted between any two SYNTESI® modules, used for independent air intake. It has 4 sockets for terminal connections on each plane. Size: SY1, SY2. Operating pressure: up to 15 bar for SY1 and up to 13 bar for SY2. Operating temperature: from -10°C to +50°C. Flow rate: 500 - 2000 l/min - SY1, 1500 - 4500 l/min - SY2, (at an inlet pressure of 6 bar Δp = 1 bar).
Select options This product has multiple variants. The options may be chosen on the product page / DetailsTool facilitating the disconnection of pipes in the SPEEDFIT system. Material: plastic.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsProtective cap for SPEEDFIT connections preventing unintended disconnection, used in compressed air installations. Material: plastic.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAluminum pipe cutter with a diameter of 4 ÷ 30 mm, for use in the SPEEDFIT system. Material: plastic.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection with an external BSP or metric threaded stub for connecting plastic hoses (for polyurethane hoses, a minimum hardness according to Shore (A) 98° is required). Material: nickel-plated brass. Operating temperature: from -15°C to +130°C. Working pressure: 30 bar. Sealing: viton.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMembrane-type pressure reducing valve with an integrated pressure gauge in the knob, ideal for panel mounting. It features an atmospheric air vent. High accuracy in maintaining outlet pressure. Available components for panel mounting (EW-367K33). Material: zinc and aluminum alloy. Size: 3/8”. Supply pressure: up to 25 bar. Operating temperature: from -10°C to +90°C. Connection: 3/8" BSP female thread. Flow rate 1000 l/min (at an inlet pressure of 8 bar and Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble-acting actuator with magnet and damping ISO 15552 series 3. It features a special sleeve with minimized weight, made of anodized, calibrated aluminum, and two grooves for sensor mounting on a common plane with power supply ports. The remaining walls are smooth and easy to clean. The actuator cover is made of high-pressure aluminum casting. Piston diameter: Ø 32 ÷ 100 mm. Stroke length: from 50 to 800 mm. Operating pressure: from 0.4 to 10 bar. Sealing: NBR, polyurethane. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe CMPC series compact actuator, with an internally threaded piston rod, is characterized by its lightweight and short design, allowing for installation in hard-to-reach places. The special profile of the actuator is connected to the outer covers using screws, ensuring optimal axial stiffness and increasing the variety of mounting options. Depending on the version, it may or may not be equipped with a magnet embedded in the piston, and grooves in the profile allow for the use of magnetic sensors without additional equipment. Manufactured according to ISO 15552 standard. This standard allows for easy and quick selection and replacement of the actuator during machine maintenance work. Piston diameter: Ø 32 ÷ Ø 100. Actuator type: double-acting, double-acting with a through piston rod, and single-acting with a retracted piston rod. Piston rod material: C45 chrome-plated steel or stainless steel. Maximum operating pressure: up to 10 bar. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSingle-acting actuator ISO 15552 type A, features a cover made of high-pressure aluminum casting and a profile made of calibrated anodized aluminum, which includes longitudinal grooves on three walls allowing for direct mounting and protection of the piston position sensors. The same grooves are used for direct mounting of valves and other mechanical components. Piston diameter: Ø 32 ÷ 63 mm. Stroke length: from 30 to 200 mm. Operating pressure: from 0.4 to 10 bar. Sealing: polyurethane. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble-acting short-stroke actuator with rotation protection using a magnet. The SSCY series is characterized by a compact design and is intended for installation in confined spaces. The operational lifespan of actuators without transverse load with NBR seals is 15 million cycles, and with polyurethane seals, it is 30 million cycles. Due to the variability of many factors affecting lifespan, the presented values should not be considered binding or guaranteed, but only as a reference. Available piston diameters: Ø 12 ÷ 80 mm. Working stroke: from 10 to 80 mm. Seal material of the actuator: NBR, polyurethane. Operating pressure: from 0.4 to 10 bar - depending on the piston diameter. Operating temperature: from -10°C to +80°C - depending on the type of seal.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe CMPC series compact actuator, with an externally threaded piston rod, is characterized by its lightweight and short construction, allowing for installation in hard-to-reach places. The special profile of the actuator is connected to the outer covers using screws, ensuring optimal axial stiffness and increasing the variety of mounting options. Depending on the version, it may or may not be equipped with a magnet embedded in the piston, and grooves in the profile allow for the use of magnetic sensors without additional accessories. Manufactured according to the NFE 49-004-1 and 2 standards (UNITOP). This standard allows for easy and quick selection and replacement of the actuator during machine maintenance work. Selected actuators have a through hole in the piston rod. Piston diameter: Ø 32 ÷ Ø 100. Actuator type: single-acting and double-acting. Piston rod material: C45 chrome-plated steel or stainless steel. Minimum operating pressure: 0.4 ÷ 0.6 bar, depending on the diameter. Maximum operating pressure: up to 10 bar. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble-acting cylinder with a passing double rod can be used as an actuator in systems where protection against rotation is required. Axial dimensions compliant with ISO 15552 standard. Standard configuration with magnet and cushioning. Piston diameter: Ø 32, 40, 50, 63, 80, 100 mm. Maximum recommended stroke length: from 25 to 500 mm. Operating pressure: up to 10 bar. Sealing: polyurethane. Working medium: filtered compressed air, oiled or non-oiled. Forces generated at 6 bar extend/retract: Ø 32 - 434/350 N, Ø 40 - 678/597 N, Ø 50 - 1060/940 N, Ø 63 - 1683/1471 N, Ø 80 - 2714/2295 N, Ø 100 - 4241/3812 N. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsA pneumatic lubricator is a simple and widely used solution that ensures proper lubrication with an oil mist for actuating devices in pneumatic systems. The oil suction process occurs due to the pressure drop created in the Venturi nozzle. The amount of oil droplets introduced into the air stream is regulated by an adjustment needle. There are auxiliary connections on the rear and front surfaces of the lubricator for connecting a manometer, pressure sensor, or for additional air intake. Size: SY1, SY2. Tank capacity: 60 cm³ - SY1, 130 cm³ - SY2. Supply pressure: up to 15 bar for SY1 and up to 13 bar for SY2. Operating temperature: from -10°C to +50°C. Connection: BSP 1/8" to 3/8" for SY1 and BSP 3/8" to 1" for SY2. Flow rate: 1600 l/min - 1/8", 3000 l/min - 1/4", 3650 l/min - 3/8", 6100 l/min - 1/2", 3/4", 1" (at an inlet pressure of 6 bar Δp = 1 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCompressed air lubricator with polycarbonate tank, ensures proper lubrication of devices in pneumatic installations with oil mist. Size: DN6. Installation: vertical. Housing material: brass. Sealing: NBR. Tank capacity: 40 cm³. Supply pressure: up to 16 bar. Operating temperature: from -10°C to +50°C. Connection: G 1/4" BSP. Flow rate: 1160 l/min (at inlet pressure 6 bar Δp = 1 bar). Weight: 400 g.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBANJO screw with O-ring and internal thread type D9 for couplings type R28, R29. Material: nickel-plated brass. Working pressure: 18 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWall mounting screw for the SYNTESI system (1 piece). Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble BANJO screw with O-ring type D8 for couplings type R28, R29. Material: nickel-plated brass. Working pressure: 18 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMounting screws for the NEW DEAL CVA system (2 pieces). Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTensioning screws (assembly) intended for the NEW DEAL F+L system (2 pieces). Material: galvanized steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsL-shaped stainless steel tee type 62450, 1x external BSPT thread and 2x internal BSP thread. Material: AISI 316L steel. Operating temperature: from -20°C to +225°C. Working pressure: 140 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsT-shaped stainless steel tee type 62440, 1x external BSPT thread and 2x internal BSP thread. Material: AISI 316L steel. Operating temperature: from -20°C to +225°C. Working pressure: 140 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdjustable "T" plug coupling with external BSP thread for connecting plastic hoses (for polyurethane hoses, a minimum hardness according to Shore (A) 98° is required). Material: nickel-plated brass. Operating temperature: from -15°C to +130°C. Working pressure: 30 bar. Sealing: viton.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBSPT threaded elbow with external tapered thread, series F type R 39 NSF. Designed for the food industry (e.g., for cold or hot drinking water). No plastic components, nickel-coated through a special chemical process, and Viton seals provide high resistance to detergents and other chemicals. Also suitable for various applications in the chemical, pharmaceutical, electronic industries, and in medicine. Operating temperature: from -20°C to +150°C. Working pressure: 16 bar. Vacuum: 0.99 bar. Material: nickel-plated brass. Seal: Viton (approved for food contact by the FDA). Standards: NSF/ANSI 51, NSF/ANSI 61.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsElbow tee, rotary, screw-in with external cylindrical thread, series F type R 38 NSF. Designed for the food industry (e.g., for cold or hot drinking water). No plastic components, coated with nickel in a special chemical process, and seals made of Viton ensure high resistance to detergents and other chemicals. Also suitable for various applications in the chemical, pharmaceutical, electronic industries, and in medicine. Operating temperature: from -20°C to +150°C. Working pressure: 16 bar. Vacuum: 0.99 bar. Material: nickel-plated brass. Seal: Viton (approved for food contact by the FDA). Standards: NSF/ANSI 51, NSF/ANSI 61.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAdjustable "T" plug tee with external thread, type R32C, intended for connecting pipes and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: nickel-plated brass. Working pressure: 16 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +80°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDouble "T" plug connector with external thread, type R51, designed for connecting hoses and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: nickel-plated brass. Working pressure: 16 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +80°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality "T" branch connection with external parallel thread (BSP or M5), made entirely of AISI 316L stainless steel, series 60215. No plastic components, and seals made of Viton ensure high resistance to corrosive agents and chemicals. Used in the chemical, food, pharmaceutical, electronic industries, and in medicine. Material: AISI 316L steel. Operating temperature: from -15°C to +225°C. Working pressure: 15 bar. Vacuum: 0.99 bar. Seal: Viton.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTriple plug tee with external thread, type R53, designed for connecting hoses and other components in pneumatic systems. Easy and quick to use for multiple assemblies without loss of sealing on the mechanical and pneumatic sides. Material: nickel-plated brass. Working pressure: 16 bar. Working medium: vacuum, air. Operating temperature: from -20°C to +80°C. Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsTee with water separator for the SPEEDFIT system used in compressed air installations, for an outer pipe diameter of 22 mm. Material: plastic. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMultiple rotary connection at the inlet with internal BSP thread, at the outlet with internal BSP threads. Working pressure: 12 bar. Operating temperature: from -10°C to +80°C. Material: nickel-plated brass.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWater separator for a 28 mm diameter pipe tee for the SPEEDFIT system. Material: brass. Working pressure: 10 bar (+23°C), 7 bar (+70°C). Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe LAM L pressure indicator in the version with a threaded connection with an O-ring on one side and a plug connection on the other side (thread - hose) is used to signal (green or orange signal) the aeration of the system; when the system is vented, the sight glass indicator is "empty." Operating pressure: 2 ÷ 10 bar. Operating temperature: from -20°C to +60°C. Medium: filtered compressed air, oiled or non-oiled.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBC bracket for mini cylinder ISO 6432. Includes 1 pin and 2 retaining rings. Cylinder sizes: Ø8, Ø10, Ø12, Ø16, Ø20, Ø25. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSupport bracket model BC for cylindrical actuator series RNDC. Supplied with 2 screws. Actuator size: Ø32, Ø40, Ø50. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMounting bracket for wall (pair), intended for the BIT system 1/8" and 1/4".
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsElectric plug 15 mm. Color: black or transparent.
