Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for cooling water in foundries, casting plants, and all applications where rubber hoses operate close to a heat source. Glass fiber covering resistant to temperatures up to +530°C caused by thermal radiation. Used in cooling systems. Particularly recommended for water installations near metallurgical furnaces. Resistant to short-term exposure to splashes of molten hot metal. Roll length: 60 m or 120 m. Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: EPDM rubber covered with glass fiber. Working pressure: 10 bar. Operating temperature: from -40°C to +120°C, external up to +530°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGeneral-purpose hydraulic hose with reduced outer diameter and weight, and increased flexibility. Complies with standards: EN 857 2SC, EN45545-2. Inner layer: black synthetic rubber. Reinforcement: double steel braid. Outer layer: black, flame-retardant synthetic rubber. Working pressure: from 90 bar to 400 bar depending on hose diameter. Operating temperature: from -40°C to +100°C. For water and air, maximum operating temperature +70°C. For air above 17 bar, micro-perforation of the outer layer is required.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, flexible hose with calibrated outer diameter, intended for pneumatic, hydraulic, oil, fuel, lubrication, and chemical installations. Available in colors: natural, black, blue, red, yellow. Hose material: polyamide PA 12 (nylon). Working pressure: from 19 bar to 28 bar, depending on the diameter and wall thickness of the hose. Operating temperature: from -40°C to +80°C (for water-based media +70°C). Standard: SAE J 844 (diameters from 1/8" to 5/16").
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, colorless, transparent, flexible hose that is odorless and tasteless, non-toxic, and free of DEHP phthalates. Specifically designed for use in peristaltic pumps. Used for dispensing and portioning cold and hot food products, for soaps and detergents, for paints, and in laboratories. The soft hose material (60° Shore (A)) is highly flexible and provides excellent longevity of over 500 hours of operation in a peristaltic pump. The hose is a good alternative to commonly used PVC or silicone hoses. It remains flexible even at -40°C and withstands elevated temperatures up to +121°C. It has good chemical resistance to a range of chemicals, such as acids and bases. Not recommended for fats, high-proof alcohols, and hydrocarbons. Resistant to ozone, oxygen, and sunlight, and is difficult to ignite. Characterized by low extractability (migration of material components into the medium). Meets hygiene and food contact requirements: European 10/2011 EU (for conditions and substances according to certification), American FDA, NSF-51. Sterilization possible by steam, ethylene oxide, or radiation. Full hose roll length: 15 m. Working pressure specified relative to burst pressure with a safety factor of 1:5. Material: tygoprene® - thermoplastic elastomer styrene (TPE). Maximum operating temperature: up to +121°C. Brittle temperature: -66°C. Hardness: 60° Shore (A). Density: 0.9 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLow-pressure suction and discharge hose with a transparent inner layer made of chemically resistant PFA and a thick outer layer made of transparent silicone. Designed for various applications in the pharmaceutical, cosmetic, food, and chemical industries, where, in addition to the highest purity, aseptic conditions, and chemical resistance, observation of medium flow is required. The inner layer is made of perfluoroalkoxy polymer PFA (fluoropolymer with properties similar to Teflon), transparent, mirror-smooth, odorless and tasteless, chemically inert, meeting high hygiene requirements (FDA, USP, European EU). Reinforcement with a stainless steel spiral provides good resistance to vacuum. The thick outer layer made of platinum-cured silicone with a smooth surface features non-stick properties (the hose does not "stick") and a low coefficient of friction. It can be easily cleaned using a mild detergent. The hose design combines the advantages of PFA with the flexibility of silicone and its temperature resistance. The hose has a small minimum bend radius, is flexible and elastic at low and elevated temperatures, resistant to cyclic bending according to ASTM D 2176 and dynamic loads. Standards and hygiene requirements: inner layer: USP Class VI, 3-A Sanitary Standards 18-03 Class I, 10/2011/EU, FDA, ISO 10993-4, -10, -11, non-cytotoxic (ISO 10993 Part 5), ICH Q3D; outer layer: USP Class VI, 3-A Sanitary Standards 18-03 Class I, D.M. 21/03/73, FDA, BfR, European Pharmacopoeia 3.1.9, ISO 10993-4, -10, -11, non-cytotoxic (ISO 10993 Part 5). The hose complies with 1935/2004/EC, 2023/2006/EC (GMP), manufactured in Cleanroom ISO 14644-1 Class 8, free from phthalates, adipates, nitrosamines, animal-derived substances, substances subject to EC 1907/2006 (REACH). Confirmation of resistance and conditions of use requires contact with Tubes International. For confirmation of resistance and conditions of use, please contact Tubes International. Installation: use fittings with a smooth spigot ("tail" for the hose) that do not have sharp or high ribs that could cut or damage the inner PFA layer when tightened. The diameter of the spigot should be precisely matched to the diameter of the hose to ensure sealing. Installation with clamp sleeves or bands (clamps). Inner layer: transparent PFA polymer. Reinforcement: AISI 302 stainless steel spiral. Outer layer: transparent silicone. Working pressure: from 1 bar to 3 bar, depending on the hose diameter. Operating temperature: from -30°C to +150°C.
- Select options This product has multiple variants. The options may be chosen on the product page / Details
WEICON Anti-Seize Assembly Paste HIGH-TECH, container 120 g
All products | Cleaning agents, maintenance products, assembly compounds, and protective coatings0 złWeicon Anti-Seize High Tech assembly paste provides protection against corrosion, seizing, and "cold welding," especially on stainless steel. Recommended particularly for use in extreme conditions, e.g., at high temperatures, aggressive media, high pressures, as well as for lubricating loaded bearings and sliding surfaces (only in slow-running engines). Eliminates squeaks and creaks, has good sealing properties, allows for easy assembly and disassembly of components. Economical in use (1 kg for approximately 40 ÷ 50 m²) and free from toxic metals, NLGI consistency - class 1. Operating temperature: from -40°C to +1400°C. Conducts heat. Resistant to temperature changes and pressure loads (230N/mm²). Packaging - container 120 g. - Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrewed plug HPA of hydraulic quick couplings designed for installations with very high pressures, where there are significant mechanical loads. Used in hydraulic presses, rescue equipment, hydraulic lifts, cutters, etc. Can be connected/disconnected when there is residual pressure in the system. End caps must be ordered separately. Material: carbon steel. Sealing: NBR. Flow: 1/4" - 16.4 l/min, (?p = 4 bar), 3/8" - 21.3 l/min, (?p=4 bar). Working pressure: 700 bar. Burst pressure: 1/4" - 2100 bar (connected coupling), 3/8" - 1850 bar (connected coupling), 1/4" - 1490 bar (disconnected plug), 3/8" - 1500 bar (disconnected plug). Operating temperature: from -25°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsQuick coupling plug DN11.8 with hose end, without flange, facilitating quick connection of the water gun to the hose or other washing accessories. Material: AISI 303/304L steel. Working pressure: 200 bar. Operating temperature: up to +100°C.
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality quick-connect water plug NiTO 1/2" with internal thread. Material: chrome-plated brass. Working pressure: up to 25 bar. Operating temperature: up to +80°C. Sealing: NBR (not suitable for gasoline and oils).- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPERROT lever connector plug with a weldable connection, widely used in agricultural farms, horticulture, industry, construction, road and tunnel building, groundwater drainage, wastewater treatment plants, sewage discharge, and environmental protection. Material: carbon steel, galvanized. Working pressure: up to 10 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDry-mate disconnect connector plug with internal thread made of AISI 316 stainless steel. Used in the chemical and pharmaceutical industries, agriculture, and loading systems. Not intended for gas media. Installed on the pressure side (tank side). The plug design is based on a ball valve, which ensures completely unobstructed flow. The plug is supplied with polypropylene caps. Connector material: body - AISI 316 steel, CAMLOCK latches - AISI 316 steel. Sealing: valve - PTFE. Working pressure: up to 7 bar. Operating temperature: up to 150°C. Maximum leakage: 1 ml (1") and 2 ml (1.1/2" and 2").
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsThe safety pin is used to prevent accidental loosening of the nut on the connector plug side of the SKV. Installation between the safety clamp and the locking nut. Diameter D - outer diameter. Material: red PVC.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCompact, two-piece medium-pressure ball valve designed for demanding general applications. It can be used for precision instrumentation in the chemical, petrochemical, pharmaceutical, energy, and process engineering industries - for liquids and gases. Intended for pipeline installation. The valve features a large size range to ensure sufficiently high flow, tight shut-off (permissible internal leakage through the ball seal 0.1 Ncm³/min), high durability, and low torque. Designed for operation in fully open or fully closed positions. Each valve is pressure tested with nitrogen. Certified according to ISO 15848-1:2006 (E). Body material: AISI 316 steel. Ball and stem material: AISI 316 steel. Lever material: AISI 304 steel, PVC. Ball seal: modified PTFE. Stem seal: PTFE. Operating temperature: from -42°C to +204°C. Working pressure: up to 137 bar (depending on temperature). Connection: inch LET-LOK®.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsV3V L type shut-off valve, two-position three-way, with pneumatic system venting, in a version finished with plug-in couplings on both sides (hose - hose). Lockable version, protects against unauthorized opening. Supplied complete with a padlock and two keys. Working pressure: 10 bar. Operating temperature: from -20°C to +60°C. Medium: filtered compressed air, oiled or un-oiled.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsGA connection set, used for connecting individual components of the compressed air preparation installation series G. The set includes a coupling and 2 screws. Available in shapes: "L", "T", and "U". Supply pressure: up to 10 bar. Operating temperature: up to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHAMMER LUG coupling type 200 with a wide range of applications (for the transmission of water, air, gas, oil) meets the requirements of most medium pressure applications. The precise fit of the sealing surfaces of the female and male parts ensures reliable pressure sealing. Set: male part, female part + nut. Color: gray (male, female parts), blue (nut). Material: carbon steel A105. Connection: GW NPT. Sealing: metal/metal (cone). Pressure: 2000 PSI (138 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / Detailscoupling plug for transfer connection type VK with internal BSP thread and E-CTFE lining. Designed for installation on hose ends or piping systems with external BSP thread. Manufactured according to standard EN ISO 14420-6 (formerly DIN 28450). Used for the most chemically aggressive media, for which the corrosion resistance of AISI 316 stainless steel is insufficient. E-CTFE features very high chemical resistance over a wide temperature range (approximately from -40°C to +130°C). It is resistant to all acids, alkalis, and other aggressive substances (pH range 1 ÷ 14). It has high mechanical properties, particularly hardness and abrasion resistance. Material: stainless steel. Thread sealing (seal type GD): Teflon.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReducing adapter with external BSPT thread and internal BSP thread for use in piping connections of industrial installations. Material: ductile iron. Operating temperature: up to +300°C. Working pressure: 25 bar (up to +120°C), 20 bar (up to +300°C).
- Select options This product has multiple variants. The options may be chosen on the product page / Details8-channel comb nozzle, flat jet, finished with a 1/4" BSP external thread. Designed for blowing off various contaminants from larger surfaces: liquids, fine chips, shavings, etc. Characterized by high blowing force at low noise levels. Ideal for the construction of air knives. Suitable for harsh conditions, e.g., at very high temperatures. Compliant with OSHA standard 1910.95 (b), STD 1-13.1, and directive 2003/10/EC. Material: ULTEM1000. Working pressure: up to 10 bar. Operating temperature: from -20°C to +200°C. Flow rate: 580 l/min (at 8 bar pressure). Noise level: 81.5 dB (at 8 bar pressure). Blowing force: 5.05 N.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCEJN 116 quick coupling socket with internal thread and valve designed for hydraulic installations at very high pressures. Used in hydraulic presses, rescue equipment, hydraulic lifts, cutters, etc. Optionally, the socket can be equipped with a safety ring to prevent accidental disconnection. Supplied standard with a cap for protection against contamination. Material: hardened, galvanized steel. Sealing: NBR. Flow: 6 l/min (Δp = 4 bar). Nominal diameter: 2.5 mm. Working pressure: 1500 bar (connected coupling). Burst pressure: 3000 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality quick-connect water socket NiTO 3/4" with hose end. Material: chrome-plated brass. Working pressure: up to 25 bar. Operating temperature: up to +80°C. Sealing: NBR (not suitable for gasoline and oils).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCAMLOCK B connector socket with external BSPT or NPT thread made according to the American military standard MIL-C-27487 (A-A-59326), commonly used as a transfer connection, particularly in the petrochemical industry. Working pressure: up to 10 bar, depending on the size of the connector. Material: aluminum. Levers: AISI 304 steel (in sizes 1.1/4" to 4" - levers made of brass). Sealing: NBR.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsEAR CLIP clamp ring with 2 ears for mounting various types of low-pressure hoses reinforced with a braid or without reinforcement. Easy and quick assembly using specially designed pliers. Rounded edges inside the ring protect the hose from damage. Material: galvanized carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBSP type A9 elbow with internal thread intended for connecting pneumatic components (including hoses) together. The tightness of the connection usually requires the use of additional seals. In the case of tapered threads, Teflon tape or sealant is used; for cylindrical threads, aluminum or copper washers are required. Material: nickel-plated brass. Working pressure: 60 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / Details90° elbows for butt welding for pressure applications made from pipes. 3D model compliant with standard EN 10253-4 (stainless steel). Equivalent to manufacturing according to standard DIN 2605-1 type 3. With material certificate EN 10204 3.1. Commonly used in the industry for the construction of installations and pipelines, among others as components of complete welded angular ends for metal and rubber hoses (welded with threaded and flanged ends) and other fittings and valve components. Other sizes and materials, including elbows with metric dimensions and elbows according to ASME, are available upon request. Note: These are standard type A fittings according to EN 10253, with the same thickness for the ends to be welded and the body. Their pressure resistance is lower than that of a straight pipe of the same diameter and thickness. The working pressure of the elbow should be determined using the pressure correction factor provided in the standards EN 10253 or DIN 2605-1 (the given values are indicative and range from 0.7 to 0.8 of the pressure corresponding to the dimension of the pipe). Material: AISI 321 steel, AISI 316Ti. Working pressure: from 56 to 208 bar - depending on the diameter.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsInternal threaded end for high-pressure washers. Material: carbon steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSKV socket end with INTERLOCK type "tail" designed for hydraulic hoses type 4SH, R13, R15 (in sizes 3/4" ÷ 1.1/2"). Material: galvanized steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHydraulic end (type P - with a special "tail" for thermoplastic hose) with external BSP thread, sealing on a 60° cone (AGR). Designed for crimping in UHP thermoplastic hoses using a crimping sleeve suitable for the type of hose. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsScrewed end fitting type S2 with external BSPT thread (seal on the thread), manufactured according to standard EN 14424, intended for rubber hoses and certain types of thermoplastic hoses, with soft textile reinforcement (without wire spiral). Commonly used in the fuel sector in fuel and gas distribution lines (e.g., LPG). Basic version made entirely of brass; also available in a stainless steel version (end fitting) with a chrome-plated brass sleeve. Material: brass (B). Working pressure: 16 bar (up to 25 bar for DN25). Operating temperature: from -20°C to +65°C (from -30°C to +70°C - for LPG).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStraight tube end fitting type RST, without a nut, intended for low-pressure rubber and non-reinforced and textile-reinforced plastic hoses, with an external steel braid. Commonly used in flexible conduits for sanitary fittings, fuel systems, air systems, etc. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBrass screw connector for hoses NiTO type A with BSP thread and flat sealing. Material: brass. Working pressure: 25 bar. Operating temperature: up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMini double-acting cylinder ISO 6432 STD, type 110, without magnet, without cushioning. It is designed to operate with filtered oil-lubricated or non-oil-lubricated air and does not require additional maintenance. The cylinder is made with a stainless steel sleeve. The dimensions of the outer covers for certain diameters have been reduced, allowing for installation in confined and restricted spaces. The lifespan of cylinders with NBR seals is 15 million cycles, with polyurethane seals 30 million cycles. The presented values should not be considered binding or guaranteed, but only as a reference due to the variability of many factors, including radial and axial loads, speed, temperature, or air losses (limit values). Piston diameter: Ø 8, 10, 12, 16, 20, and 25 mm. Stroke length: from 5 to 500 mm. Operating pressure: from 0.8 to 10 bar (Ø 8, 10, 12 mm); from 0.6 to 10 bar (Ø 16, 20, 25 mm). Sealing: polyurethane, NBR, FKM/FPM. Operating temperature: from -10°C to +150°C depending on the seal used.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsNut designed for connecting male and female parts of the HAMMER LUG connector, type 1502. Material: chrome-molybdenum steel 4130.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBSP threaded nut, type VT124. Material: AISI 316 steel. The given dimensions are for reference and may vary slightly depending on the manufacturer.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDIN 3015 heavy clamp type 201 (with top plate) designed for quick, easy, durable, and aesthetic mounting of pipes, hoses, and hoses in various industrial sectors, in ground and marine installations. Manufactured according to DIN 3015 standard. The clamp is mounted to the structure using welding of the clamp base (there is an option for bolting or mounting on a rail). The clamp typically features a profiled (grooved) surface for the pipe opening. In addition to standard metal components, extended plates, rails, and screws for mounting clamp sets can be ordered. The selection of components should be consulted with TUBES INTERNATIONAL®. Clamp material: aluminum. Screw material: galvanized steel. Plate material: galvanized steel. Base material: carbon steel. Operating temperature: up to +350°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-pressure water gun SG25 with extension lance for industrial applications. Suitable for hot and cold water. The lever mechanism does not require the operator to exert significant force, resulting in comfortable and pleasant operation. The outlet part is finished with an internal thread M22x1.5. The gun is available in versions with a fixed or rotating connection to the installation. Housing material: high-strength plastic. Working pressure: up to 220 bar. Maximum pressure: 250 bar. Flow rate: 30 l/min. Operating temperature: up to +160°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWater gun for the food industry. Made of brass and stainless steel, sealing – viton. The gun is covered with a blue, non-staining, impact-resistant material, equipped with protective rings made of soft rubber. It features an adjustable outlet nozzle, smooth flow regulation, and a trigger lock. The trigger guard protects against uncontrolled water flow and damage. Maximum working pressure: 24 bar. Maximum operating temperature: +60°C (temporarily +90°C). Flow rate: 68 l/min (5 bar), max. 100 l/min.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCover for IBC pallet container with a vent and internal thread for BSP vent. The cover is supplied with a gasket. Material: polypropylene. Sealing: EPDM. Operating temperature: from -10°C to +70°C (temporarily up to +80°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPneumatic extension - ready rubber air hose made of MPX20 hose. Finished with a brass socket and Eurostandard DN7.2 quick coupling plug (compatible with standard connections). For general use, particularly for pneumatic tools, where a rubber hose with antistatic properties is required. Inner layer: black EPDM rubber. Reinforcement: textile braid. Outer layer: black EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsIndustrial hose for water and air. Widely used for washing floors and industrial equipment with hot water. Suitable for outdoor use as well. Resistant to weather conditions, ozone, and abrasion. Not resistant to oil, also not recommended for air with oil mist. Inner layer: black EPDM rubber. Reinforcement: polyester braid. Outer layer: red EPDM rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +100°C (temporarily up to 120°C).
