Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsZ2T (PH) clamping sleeve for rubber hydraulic hoses type 2SN (R2AT) or 3TE. Installation - no machining required. Use for hydraulic fittings (PH). Diameter D1 [mm] - outer diameter. Material: AISI 316 steel.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsZF2 (PH) clamping sleeve for rubber hydraulic hoses type 2ST (R2A) or 4SP. Installation - external machining. Use for hydraulic fittings (PH). Diameter D1 [mm] - outer diameter. Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsONE SKIVE clamp sleeve for rubber hydraulic hoses with spiral reinforcement type 4SP, 4SH, R12, R13, and R15. Use only with the appropriate NON SKIVE hydraulic fitting from the same supplier. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsONE SKIVE clamp sleeve for rubber hydraulic hoses with spiral reinforcement type 4SP, R13, and R15. Use only with the appropriate NON SKIVE hydraulic fitting from the same supplier. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsIL13 clamping sleeve for rubber hydraulic hoses with spiral reinforcement type R13 and R15. Use only with INTERLOCK hydraulic fittings from the same supplier. Installation - external and internal machining. Diameter D1 [mm] - outer diameter. Diameter D2 [mm] - inner diameter. Diameter D3 [mm] - lock diameter. Material: AISI 316L steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsAF-T clamp sleeve for smoothbore and HYPERLINE V teflon hoses. Material: AISI 304 or 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBPMTK clamping sleeve for thermoplastic hoses type MTK. Diameter D1 [mm] - outer diameter. Diameter D2 [mm] - inner diameter. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBP7 clamping sleeve for thermoplastic hoses type R7 (SAE100R7). Installation - no machining required. Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMC-BP7 clamping sleeve for thermoplastic hoses type R7 (SAE100R7). Assembly - no machining. Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBX8 clamping sleeve for thermoplastic hoses type R8 (SAE100R8). Installation - no machining. Diameter D1 [mm] - outer diameter. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLDR, LD, LR type sleeves are designed for clamping stainless steel hygienic ends (with a corrugated tail) type NH-xxK-xxx and ends with a tail for hose under a shell clamp RS, e.g., TW-KRS-xxx, NH-xxR-xxx in industrial hoses (rubber and plastic with textile reinforcement, possibly with a reinforcing spiral - suction and pressure hoses). The sleeve should be selected considering the internal diameter Dw and external diameter Dz of the hose. The length of the sleeve L may be slightly (a few mm) greater than the length of the tail of the end Lk. LR sleeves - only for ends under the shell clamp, LD - only for ends with a corrugated tail, LDR - sleeves for both types of ends. Diameter D1 [mm] - external diameter. Diameter D2 [mm] - internal diameter. Diameter D3 [mm] - locking diameter. Material: AISI 316 steel.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsWater gun handle AKBO with internal BSP thread in EPDM rubber cover. Material: stainless steel. Operating temperature: up to +95°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsKnife holder for the EST-L tool designed for machining the outer layer of rubber in hydraulic hoses requiring greater cutting length. Material: carbon steel, galvanized.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMeasurement handle for activation at low pressure. It has a connection for a manometer, a quick coupling with a shut-off valve, and a vent (for TA-M-101-21A - valve).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, transparent, exceptionally soft and flexible, universal laboratory hose free of phthalates (DEHP). An excellent solution for complex laboratory equipment installations requiring small bend radii and multiple curves. This ultra-soft hose is resistant to twisting and kinking and remains flexible at low temperatures (down to -55°C). Due to its softness, it does not require high forces for compression, making it an ideal solution for peristaltic pumps with low torque or battery-powered. It has a longer lifespan in peristaltic pump applications compared to typical silicone hoses, while also possessing good chemical resistance to a range of corrosive media (acids, bases, salts, alcohols). Compliant with FDA requirements for food contact and REACH. Sterilization only with ethylene oxide. Full hose roll length: 15 m. The specified working pressure is defined relative to the burst pressure with a safety factor of 1:5. Material: PVC (special, DEHP-free). Maximum operating temperature: +52°C. Brittleness temperature: -55°C. Hardness: 40° Shore (A). Density: 1.1 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, ergonomic, lightweight water gun with adjustable outlet nozzle, smooth flow regulation, and trigger lock. Housing: composite material. Nozzle: chrome-plated brass. Working pressure: up to 12 bar. Operating temperature: up to +80°C. Flow rate: 50 l/min (5 bar).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal flexible rubber pressure hose, intended for air, cold and hot water, and light chemicals (except acids). Resistant to acetates and ketones. Can be used for dispersive water-based epoxy and polyurethane paints. Not suitable for oils, fuels, aromatic hydrocarbons, cellulose paints, chlorinated rubber, and others containing aromatic solvents (e.g., toluene, xylene) or gasoline. For chemical applications, we recommend contacting Tubes International. The hose has a strong construction and low elongation under pressure. Suitable for use on reels. Inner layer electrically conductive (R<106 Ω, EN ISO 8031), outer layer resistant to ozone and weather conditions. Inner layer: black EPDM rubber. Reinforcement: textile braid (PVA - polyvinyl alcohol). Outer layer: black EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +95°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSuction and discharge hose for demanding, versatile applications in the food industry. Excellent for the transfer of various types of food products such as: olive oil, wine, beer, fruit juices, milk, fats, and alcohols with a concentration of up to 96%. The inner layer is odorless and tasteless. It does not contain phthalates and bisphenol A, as well as polycyclic aromatic hydrocarbons (PAH Free), in accordance with ZEK 01.4-08 Cat.1. Tested for heavy metals. The outer layer is resistant to weather conditions and ozone. Standards and requirements: Food industry, food contact 1935/2004/EC and EC 2023/2006/EC (GMP). The inner layer complies with FDA 21 CFR 177.2600, BfR XXI cat. 2, D.M. 21/03/73, 3-A Sanitary Standard 18-03 class II. Inner layer: white, smooth synthetic rubber. Reinforcement: synthetic cord, steel spiral. Outer layer: blue synthetic rubber. Working pressure: 10 bar. Vacuum: 0.9 bar. Operating temperature: from -30°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, semi-transparent, strong and flexible reinforced hose designed for higher pressures. Made of polyether - polyurethane, free of plasticizers, exceptionally resistant to abrasion and tearing, characterized by a small bending radius and flexibility even at low temperatures. Withstands cyclic temperature changes. Resistant to oils, greases, fuels, and a range of chemicals. Used in various industrial sectors: transfer of abrasive and viscous products, sludges and pastes, transfer of granules and powders, lubrication and degreasing, for cooling fluids in automotive applications, for air in pneumatics and industrial automation. Used in the food and cosmetic industries - meets FDA 21 CFR 177.1680 and FDA 21 CFR 177.2600 requirements for food contact and NSF-61 for use with drinking water (with hose length limitations depending on diameter). Full hose roll length 30 m (from internal diameter 31.8 mm - 15 m). Working pressure defined relative to burst pressure with a safety factor of 1:4. Material: tygothane® - polyurethane - polyether (PU). Operating temperature: from -73°C to +82°C. Brittleness temperature: -73°C. Hardness: 85° Shore (A). Density: 1.12 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, two-part, full-bore ball shut-off valve of European manufacture, made from casting, with a flange for direct actuator mounting compliant with ISO 5211, intended for industrial installations. It can be used for air, neutral gases, water, chemicals, petrochemical products, etc., free from solid contaminants, in accordance with the chemical resistance of the valve materials. It features a stem protection against blowout. Complies with the Pressure Equipment Directive PED 2014/68/EU: a) for sizes up to DN25 (1”) inclusive within good engineering practice (SEP), according to Article 4, paragraph 3 (without CE marking); b) for sizes from DN32 (1.1/4”) for liquids group 1 and 2 and for gases group 2 (other than hazardous) – CE marking, category I. Compliant with the RoHS material directive 2011/65/EU and REACH regulation 1907/2006. The stated minimum operating temperature applies to the valve emptied of freezing liquids. Body material: nickel-plated brass. Ball material: chrome-plated brass. Ball sealing: PTFE. Stem sealing: 2 x FKM (viton) o-ring. Connection: BSP thread (ISO 228-1). Operating temperature: from -20°C to +95°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal shut-off ball valve (tap) of European manufacture, made of casting, with a straight aluminum lever, with a hose connection and aerator, intended for industrial and water supply installations. It can be used for water, chemicals, petrochemical products, etc., free from solid contaminants, in accordance with the chemical resistance of the valve materials. It features a stem blow-out protection. Complies with the Pressure Equipment Directive PED 2014/68/EU, regarding good engineering practice (SEP), according to Article 4, paragraph 3 (without CE marking). Compliant with the RoHS material directive 2011/65/EU and REACH regulation 1907/2006. The working pressure depends on the operating temperature. The specified minimum operating temperature applies to the valve emptied of freezing liquid. WARNING: When used outdoors, it is necessary to drain the valve of water at negative ambient temperatures! Body material: nickel-plated brass. Ball material: chrome-plated brass. Lever material: aluminum. Aerator material: polyamide (PA). Ball sealing: PTFE. Stem sealing: 2 x NBR o-ring. Connection: BSP thread (ISO 228-1). Operating temperature: from -20°C to +110°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSimple device for cleaning hoses and pipes with compressed air. It has two nozzles made of plastic, one for hoses 3/16" to 1" and the other for hoses 1" to 2". Pressing the hose against the nozzle opens the air valve, allowing for hose cleaning. Air pressure: min. 6 bar. Pneumatic system connection: 1/2" BSP.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDevice for oil filling and suction and filtration of oil from press tanks, machines, and hydraulic systems. Parameters: electric drive 0.55 kW, 400V; pump 39 l/min; filter 25 µm (also available in 10 and 20 µm); suction filter 125 µm. Weight: 60 kg.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsDevice for oil filling, suction, and filtration from press tanks, machines, and hydraulic systems. Parameters: electric drive 400V, 0.55kW; pump 39 l/min; filter 25 µm (also available in 10 and 20 µm); suction filter 125 µm; electronic oil flow meter; electronic filter replacement indicator. Weight: 87 kg.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsRailway nut gasket compatible only with KGW type end nuts. Material: PTFE. Operating temperature: from -70°C to +220°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSeal for sealing connections to Hansen Beverage quick coupling plug 2-HG and 2-HL. Temperature: up to +130°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSeal for sealing connections to Hansen Beverage quick couplings 2-KG-F and 2-KL-F. Temperature: up to +130°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSeal for Hansen Beverage quick coupling 2-KG-F and 2-KL-F ensuring the tightness of the quick coupling. Temperature: up to +130°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsConnection seal with internal thread for NiTO quick coupling. Material: NBR. Operating temperature: up to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMetal-rubber gasket for use in high-pressure installations (for quick couplings, adapters with external threads). High-strength version. Working pressure: up to 1500 bar.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat gasket FF for 4" TTMA flange. The permissible working pressure at which the gasket can be used depends on the temperature and type of medium (selection should be agreed with TUBES INTERNATIONAL®). Material: EPDM, SPETOGRAF GUS31, PTFE, viton. Working pressure: up to 60 bar (EPDM), up to 100 bar (SPETOGRAF GUS31), up to 300 bar (PTFE). Operating temperature: from -30°C to +120°C (EPDM), from -200°C to +650°C (SPETOGRAF GUS31), from -200°C to +220°C (PTFE), from -20°C to +200°C (viton).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat gasket intended for connections with internal threads. For food applications. Not resistant to greases and oils. Material: silicone. Operating temperature: from -60°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat gasket for CAMLOCK AU and DU connections designed to seal the internal thread connection with the external cylindrical thread. Material: polyurethane. Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat gasket IBC for flange PN made according to standard PN-EN 1514-1. The permissible working pressure at which a given gasket can be used depends on the temperature and type of medium (selection should be agreed with TUBES INTERNATIONAL®). When selecting a gasket, attention should be paid to the outer diameter dimension, appropriate for the flange class. For example: gasket DN 10 PN40 is suitable for classes PN10, PN16, and PN25. Material: SPETOGRAF GUS31. Working pressure: up to 100 bar. Operating temperature: from -200°C to +650°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCover gasket MB (for tank truck connections) type TWF (for 4" connection, use O-ring gasket type TWO). Material: ethylene-propylene-diene rubber (EPDM). Temperature range (approximate): from -20°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsCover gasket MB (for tank truck connections) type TWF (for 4" connection, use O-ring gasket type TWO). Material: polyurethane (PUR). Temperature range (approximate): from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsKKG gasket intended for the socket of the LAUX 42 lever coupling. Good resistance to ozone and weather conditions. Suitable for water and air. Material: EPDM. Operating temperature: from -50°C to +120°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsKKG gasket intended for the socket of the LAUX 42 lever coupling. Resistant to mineral oils, gasoline, and most chemicals. Not suitable for solvents containing ketones. Material: viton. Operating temperature: from -30°C to +250°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSeal for symmetrical joints standard GOST no. 28352-89, 2217-66 (Russia). Material: NBR rubber. Operating temperature: from -10°C to +80°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlat gasket for Guillemin connection. Material: EPDM.
