Our products
Product categories
Working pressure [bar]
Minimum operating temperature [°C]
Maximum operating temperature [°C]
Material
Vacuum resistance
Standard length [m]
Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for low-pressure parts of hydraulic power systems, compliant with SAE 100 R6 and ISO 4079 R6 standards. Designed primarily for hydraulic fluids based on mineral oil and some synthetic hydraulic fluids. It can also be used for water-based hydraulic fluids as well as for water and air with a temperature limit of +70°C (air applications may require micro-perforation of the outer layer). Suitable for many liquid products in the petrochemical industry: mineral and synthetic oils, diesel and heating oil, ethylene glycol, and others. Not recommended for gasoline and ester-based oils, unsuitable for aromatic hydrocarbons. Inner layer made of black, smooth synthetic rubber. Reinforcement with textile braid. Outer layer made of black synthetic rubber, resistant to abrasion, oil, ozone, and weather conditions. Inner layer: black synthetic rubber. Reinforcement: single textile braid. Outer layer: black synthetic rubber. Working pressure: from 12 bar to 28 bar - depending on the hose diameter. Operating temperature: from -40°C to +100°C.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong and lightweight pressure hose with a thin wall, almost flat in a resting state, designed for operation in harsh conditions. Used for the transmission of industrial water and wastewater, for submersible pumps, drainage and irrigation systems, mobile irrigation. Resistant to abrasion, weather conditions, and ozone. The hose construction allows for easy coiling after use. Installation using straps or clamps. Standard length: 60 m (or 120 m - contact Tubes International). Inner layer: black synthetic rubber. Reinforcement: polyester cord. Outer layer: black synthetic rubber. Working pressure: 10 bar. Operating temperature: from -25°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality rubber pressure hose manufactured in the USA with an inner layer made of chemically resistant polyamide (nylon). The very smooth inner surface reduces flow losses and ensures ease of cleaning. Reinforcement with synthetic textile braiding provides high pressure resistance and low deformation under pressure. The smooth outer layer made of synthetic rubber is resistant to contact with chemicals and oil (RMA Class B – medium resistance). For hoses with an inner diameter of 1/4" and 3/8", the outer layer is antistatic R<106Ω. The hose is intended for industrial applications, particularly for organic solvents and petrochemical substances. The good resistance of polyamide to many solvents allows the hose to be used in the paint industry for the transfer of paints, varnishes, adhesives, and resins. Chemical resistance and potential static electricity issues must always be considered. In particular, antistatic hoses with diameters of 1/4" and 3/8" are widely used as pressure feed hoses for spray guns in automotive workshops, construction, and industry. Chemical resistance verification: chemical resistance table for PA (preliminary selection), confirmation of resistance and application conditions by Tubes International. Installation: smooth fittings with a spigot ("tail" for the hose) without sharp or high ribs that could cut or damage the inner polyamide layer when tightened should be used. Typical hydraulic fittings can be used. The spigot diameter should be precisely matched to the hose diameter to ensure sealing. Installation depending on working pressure with hose clamps, crimp fittings, or for larger diameters with shell clamps. Typical factory hoses for spray guns often have reusable screw fittings. Inner layer: polyamide (PA), silicone-free. Reinforcement: single textile braid for 1/4" and 3/8", double for 1/2". Outer layer: black synthetic rubber. Working pressure: 52 bar. Operating temperature: from -20°C to +90°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSpecial high-pressure version of the SMOOTHBORE Teflon hose with a thickened wall made of specially processed Teflon (reduced microporosity) for applications with high-pressure gases in a double braid (aramid and steel braid) and with an outer layer of Hytrel. The outer layer of Hytrel is available in four colors: black, blue, green, and red, to indicate the hose's intended use for a specific type of gas. When both HPG inner layer and AS antistatic layer are required, the HPG/AS hose (red color) can be used, featuring an additional thin AS antistatic layer inside the primary inner layer of natural HPG Teflon. Installation: use AF-TL series fittings and sleeves... Hose material: smooth PTFE (Teflon) HPG. Reinforcement: aramid braid + AISI 304 steel braid. Outer layer: microperforated Hytrel (colored polyester). Working pressure: 300 bar. Operating temperature: from -50°C to +70°C (due to the outer layer of Hytrel).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong pressure hose designed for the transmission of water or compressed air in irrigation systems, agriculture, mines, construction sites, etc. The inner layer is smooth, ensuring minimal flow loss. The outer layer is slightly longitudinally ribbed, which increases abrasion resistance and protects against contact with hot elements. Resistant to abrasion, ozone, weather conditions, oil, fuels, and a wide range of chemicals. Lighter and more flexible than standard rubber hoses. Flat when at rest, facilitating handling and storage. Does not require washing and drying. Resistant to longitudinal loads – during unwinding and pulling (longitudinal force should never exceed 1/3 of the specified breaking force, installation of fittings should consider longitudinal force). Use for air should always be preceded by a risk analysis in case of accidental disconnection or rupture of the hose. Hose material: black NBR/PVC blend embedded in a polyester-polyamide braid during the hose extrusion process. Working pressure: from 10 bar to 25 bar (water), from 7 bar to 18 bar (air) - depending on the hose diameter. Operating temperature for water: from -20°C to +80°C, temporarily up to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality universal hose designed for air, cold and hot water, oil, hydraulic fluids, light chemicals, diluted acids, cleaning fluids. Strong and flexible, resistant to twisting and kinking. Non-soiling outer layer, weather-resistant, abrasion-resistant, and oil-resistant. Due to its high durability and low elongation, it is particularly recommended for drum reels. The hose is non-conductive (R > 1 MΩ per inch of hose length at 1000 V DC). Inner layer: black NBR rubber. Reinforcement: synthetic braid. Outer layer: blue (red for diameter 15.9 mm) Chemivic® rubber blend (NBR/PVC). Working pressure: 21 bar. Operating temperature: from -29°C to +88°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for the transmission of various chemical substances, mainly for acid solutions, bases, ketones, aldehydes, industrial alcohols, and glycols. Basic, classic rubber chemical hose. Frequently used in industrial plants and wastewater treatment facilities for discharging contaminated water and process water. Also suitable for seawater. Inner layer made of antistatic (R ≤ 10^6 Ω/m) EPR rubber (other designation: EPM). Reinforcement made of high-strength cord. Outer layer made of antistatic (R ≤ 10^6 Ω/m) EPR (EPM) rubber resistant to chemicals, abrasion, ozone, and weather conditions. Both inner and outer layers are antistatic. Inner layer: black EPM (EPR) rubber. Reinforcement: synthetic cord. Outer layer: black EPM (EPR) rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose made according to hydrogen peroxide enhancement technology. Resistant to UV radiation, oxygen, and ozone. Widely used in industry and household appliances. Sterilization by steam, ethylene oxide, or radiation. Meets FDA and BfR requirements. Material: translucent silicone. Hardness: 57° Shore (A). Density: 1.15 g/cm³. Operating temperature: from -50°C to +200°C (temporarily +220°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flexible delivery hose, flat-foldable, for water to hydrants and equipment used by fire services. Supplied with mounted aluminum STORZ type fittings (complete hose), compliant with the technical conditions of the MSWiA Regulation of April 27, 2010, and has a CNBOP-PIB approval certificate. The hydrant hose complies with the EN 14540 standard and is used in internal hydrants according to EN-671-2. The pump hose is used for fire pumps, rescue pumps, and forestry services. In addition to fire-fighting functions, it is widely used in industry, construction, agriculture, and mining. Also available in a yellow luminescent version (DN52, DN75, 20m, for pumps). It can be used for the transmission of water, seawater, industrial water, and solutions of certain chemical substances. Inner layer: PVC insert (PU for DN110). Reinforcement: polyester braid. Working pressure: from 12 bar to 15 bar - depending on the hose diameter. Operating temperature: from -30°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsUniversal, highly flexible, unreinforced hose designed for non-pressurized (or very low-pressure) transfer of air, water, and liquids in general industrial applications, light chemicals (e.g., diluted acids and bases), and as a protective cover for pipes, conduits, hoses, etc. It can be used (at temperatures up to +40°C) for food substances such as juices, beverages, beer, wine, alcohols with concentrations up to 50%, milk, and its derivatives. Not recommended for oils and fatty food substances. The CRISTALLO EXTRA hose complies with European requirements 1935/2004/EC, 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP). Suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). The stated working pressure is an indicative value of the recommended working pressure with a safety factor of 5:1. Hose material: transparent PVC. Operating temperature: from -20°C to +60°C, working pressure dependent on temperature.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality hydrophobic pressure hose manufactured using platinum-enhanced technology. Odorless and tasteless. Smooth surface prevents contamination adhesion. Sterilization by steam at +135°C, alternatively by argon, cobalt. Compliant with FDA requirements, USP Class VI, European Pharmacopoeia 3.1.9, and directives EC 1935/2004 and EC 2023/2006 (GMP). Safety factor 3:1. Inner layer: translucent silicone. Reinforcement: polyester braid. Outer layer: translucent silicone. Operating temperature: from -60°C to +200°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsMultifunctional, lightweight, exceptionally flexible and elastic hose resistant to oil and gasoline. Designed for air, water, oils, fuels, lubricants, chemicals (e.g., light acids and bases), pesticides, fertilizers, etc. Smooth outer layer resistant to weather conditions, aging, ozone, UV radiation, non-soiling. Popular and widely used in industry, construction, agriculture, automotive workshops. Inner layer: black NBR/PU/PVC blend. Reinforcement: polyester braid. Outer layer: black NBR/PVC blend. Working pressure: 25 bar. Operating temperature: from -20°C to +70°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsExceptionally flexible hose designed for compressed air. Due to features such as: lightweight, flexibility at low temperatures, resistance to elongation, it is particularly recommended for pneumatic tools, compressors, hose reels, etc. Inner layer: black PVC. Reinforcement: polyester braid. Outer layer: blue PVC. Working pressure: 15 bar. Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality, highly flexible, resistant to twisting and bending universal industrial hose. Used in industry, construction, agriculture, quarries, mining, and road construction, in the oil and shipbuilding industries. The inner layer is resistant to oil, grease, light chemicals, air, kerosene, cold and hot water. The outer layer has very good abrasion resistance and resistance to animal fats and oils. Due to its high strength and low expansion, it is particularly recommended for drum reels. Outer flame resistance complies with MSHA standard 2G-14C/39. Non-conductive (R > 1 MΩ per inch of hose length at 1000 V DC). Inner layer: black NBR rubber. Reinforcement: aramid braid, for 2" synthetic braid. Outer layer: yellow Carbryn® rubber (XNBR, carboxylated NBR). Working pressure: 35 bar. Operating temperature: from -29°C to +88°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed for cooling water in foundries, casting plants, and all applications where rubber hoses operate close to a heat source. Glass fiber covering resistant to temperatures up to +530°C caused by thermal radiation. Used in cooling systems. Particularly recommended for water installations near metallurgical furnaces. Resistant to short-term exposure to splashes of molten hot metal. Roll length: 60 m or 120 m. Inner layer: black EPDM rubber. Reinforcement: synthetic cord. Outer layer: EPDM rubber covered with glass fiber. Working pressure: 10 bar. Operating temperature: from -40°C to +120°C, external up to +530°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPneumatic extension - ready rubber air hose made of MPX20 hose. Finished with a brass socket and Eurostandard DN7.2 quick coupling plug (compatible with standard connections). For general use, particularly for pneumatic tools, where a rubber hose with antistatic properties is required. Inner layer: black EPDM rubber. Reinforcement: textile braid. Outer layer: black EPDM rubber. Working pressure: 20 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsIndustrial hose for water and air. Widely used for washing floors and industrial equipment with hot water. Suitable for outdoor use as well. Resistant to weather conditions, ozone, and abrasion. Not resistant to oil, also not recommended for air with oil mist. Inner layer: black EPDM rubber. Reinforcement: polyester braid. Outer layer: red EPDM rubber. Working pressure: 10 bar. Operating temperature: from -40°C to +100°C (temporarily up to 120°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsBlack, opaque, and flexible hose made of fluoroelastomer (Viton), resistant to fuels, solvents, oils, and chemicals, particularly at elevated temperatures. Used for concentrated acids, bases, alcohols, chlorinated and aromatic solvents, hot fuels, and oils. Suitable for peristaltic pumps. Resistant to aging, ozone, sunlight, and weather conditions. Flame-retardant. The opaque black wall of the hose protects light-sensitive substances. Used in laboratories and general industrial applications. Provides an economical alternative to VERSILONTM F-5500-A hose. Full roll length of the hose is 50 m (for internal diameters from 4 mm to 12 mm - 25 m, from 15 mm - 5 m). The specified working pressure is defined relative to the burst pressure with a safety factor of 1:5. Material: fluorine rubber (FKM). Operating temperature: from -20°C to +200°C (temporarily up to +300°C). Brittleness temperature: -20°C. Hardness: 60° Shore (A) - for 4x6 mm, 70° Shore (A) - for 4x8 mm. Density: 1.90 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsReinforced polyester silicone hose is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version with a fluorosilicone inner layer is recommended. Standard length: 1000 mm (also available in a 2000 mm section). Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approximately 65° Shore (A), density approximately 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers. Working pressure: from 0.86 bar to 8.75 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose for the transmission of almost all aggressive chemical substances. Specifically designed for the petrochemical industry for fuels with high concentrations of aromatic hydrocarbons, hot oil, and solvents. Due to the high overall chemical resistance of FPM rubber, it can be used for aggressive chemicals, in many cases also at elevated temperatures. The inner layer is made of smooth black FKM fluorine rubber. Reinforcement with synthetic cord. The outer layer is made of CR chloroprene rubber, resistant to weather conditions, ozone, abrasion, and oils. Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50ºC. Inner layer: black FKM rubber (FPM, viton). Reinforcement: synthetic cord. Outer layer: black CR rubber. Working pressure: 10 bar. Operating temperature: from -25°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose connector RADIATOR intended for engine cooling systems in vehicles and automotive-type engines (for water, coolant fluids based on ethylene glycol). Meets the requirements of standard SAE J20 R4 Class D-1. Available as a simple connector with a length of 1000 mm. Working pressure: from 0.6 bar to 3.7 bar, depending on the diameter of the connector. Operating temperature: from -40°C to +125°C. Safety factor (burst pressure / maximum working pressure) 3:1. Connector material: black EPDM rubber. Reinforcement: textile braid.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight multi-layer hose with an inner layer made of abrasion and oil-resistant polyurethane, intermediate and outer layers made of thermoplastic blend and PVC. Highly flexible, with a small bending radius, non-kinking. Resistant to ozone, fats, oils, and light chemicals. Designed for compressed air and fluids. Widely used in the industry for pneumatic tools, air for spray guns and water-based paint applications, sandblasting, etc. Suitable for mounting on reels. The inner layer is approved for food contact - compliant with European regulations 1935/2004/EC and 10/2011/EU (simulated fluids A, B, and C), 2023/2006/EC (GMP). Inner layer: transparent polyurethane. Intermediate layer: PVC/PU (black color). Reinforcement: polyester braid. Outer layer: TPE/PVC (turquoise color). Working pressure at 20°C: 20 bar. Operating temperature: from -15°C to +60°C. As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible, biologically neutral hose manufactured using hydrogen peroxide enhancement technology. Retains chemical, electrical, and mechanical properties at temperatures up to +200°C. Sterilization by steam, ethylene oxide, radiation. Complies with FDA, BfR, USP (class VI), ISO 10993 quality standards (toxicity, irritation, cytotoxicity, hemolysis). Material: translucent silicone. Hardness: 62° ±5° Shore (A). Density: 1.15 ±0.03 g/cm³. Operating temperature: from -50°C to +200°C (temporarily +230°C).
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPressure hose for the transport of anhydrous ammonia in liquid and gaseous form. Inner layer made of thick antistatic rubber (R≤106 Ω/m). Reinforcement with high-strength cord ensures a high safety factor of 5:1. Outer layer made of antistatic rubber (R≤106 Ω/m) resistant to chemicals, abrasion, ozone, and weather conditions, microperforated. Hose compliant with the requirements of standard EN ISO 5771:2008 for rubber hoses for the transport of anhydrous ammonia. The hose is particularly intended for ammonia in the production processes of nitrogen fertilizers, cleaning agents, and for the synthesis of many chemical compounds. It can also be used in other industrial sectors utilizing anhydrous ammonia, such as industrial refrigeration (refrigerant R717 – ammonia, used in large refrigeration systems; flexible hoses are primarily used for filling installations), metallurgy, and many others. The hose can also be used for ammonia dissolved in water - ammoniacal water, widely used in industries such as wastewater treatment (pH regulator), ion-exchange resin regeneration, rubber and plastics industry, and boiler water treatment. Inner layer: black synthetic rubber. Reinforcement: synthetic cord. Outer layer: black synthetic rubber, microperforated. Working pressure: 25 bar. Operating temperature: from -40°C to +55°C.
Select options This product has multiple variants. The options may be chosen on the product page / Details90° ELBOW RADIATOR designed for engine cooling systems in vehicles and automotive-type engines (for water, ethylene glycol-based coolants). Meets the requirements of standard SAE J20 R4 Class D-1. Available with arm lengths of 200, 250, and 300 mm. Working pressure: from 0.6 bar to 4.1 bar, depending on the diameter of the elbow. Operating temperature: from -40°C to +125°C. Safety factor (burst pressure / maximum working pressure) 3:1. coupling material: black EPDM rubber. Reinforcement: textile braid.- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight, flat (in a resting state), pressure hose designed for water transmission. An economical solution for average working conditions. Used in agriculture, construction, and other industrial sectors. Available in two versions: HIFLAT LD (green) and HIFLAT HD (blue). Inner layer: black PVC. Reinforcement: polyester spacer. Outer layer: green PVC (LD), blue PVC (HD). Working pressure: from 2.5 bar to 10 bar - depending on the hose diameter, temperature, and type of hose (LD, HD). Operating temperature: from -20°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsPneumatic extension – ready air hose made of WTZ hose with a diameter of 10 mm and a length of 10 or 15 m. Finished with a brass socket (TP-ES72-GK-10) and a plug (TP-ES72-WK-10) of the standard Eurostandard DN 7.2 pneumatic quick coupling. The simplest solution for connecting pneumatic tools. Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: transparent PVC. Working pressure at a temperature of 20°C: 10 bar. Operating temperature: from -5°C to +50°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality silicone hose widely used in the industry (e.g., in cooling systems and for hot air). Exceptionally resistant to mineral oil vapors. Hardness 65° Shore (A). Inner layer: blue silicone. Reinforcement: textile inserts. Outer layer: blue silicone. Operating temperature: from -60°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone elbow 90° reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, the version with a fluorosilicone inner layer is recommended. Arm length: 100 mm (also available with arm lengths of 152, 250 mm). Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester inserts. Working pressure: from 1.83 bar to 8.75 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsFlexible general-purpose hose reinforced with a braid for compressed air, water, and light chemicals. It can be used (at temperatures up to +40°C) for liquid and semi-liquid food products such as juices, beverages, beer, wine, alcohols with a concentration of up to 50%, milk, and its derivatives. It is not recommended for oils and fatty food substances. The REFITTEX CR hose complies with European requirements 1935/2004/EC, 10/2011/EU (simulants A, B, C, and D1), 2023/2006/EC (GMP). It is suitable for temporary contact with food during the transfer of food substances - under the conditions specified in the manufacturer's declaration of conformity (available at Tubes International). Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: transparent PVC. Working pressure: from 5 bar to 30 bar, depending on the hose diameter. Operating temperature: from -20°C to +60°C, working pressure dependent on temperature.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsLightweight, transparent, flexible hose made of patented thermoplastic elastomer for biotechnological applications. Suitable for use in peristaltic pumps. Non-toxic, non-hemolytic, and apyrogenic with high purity class, easily thermally weldable, which is essential in biotechnological processes. Sterilization possible in autoclave, radiation, and ethylene oxide. Resistant to concentrated acids and bases. Meets USP Class VI requirements. Hose material: thermoplastic elastomer. Hardness: 60° Shore (A). Operating temperature: from -45°C to +135°C. Key features: thermal welding using C’eal-Flex™ TPE Ultra Sealer.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight economical hose, flat in a resting state, designed for water transmission. An economical solution for low working pressures and non-demanding working conditions. Used in agriculture, e.g., for irrigation of crops, construction, and other industrial sectors. Hose material: blue PVC. Reinforcement: polyester layer. Working pressure: 3 bar. Operating temperature: from -5°C to +60°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHigh-quality multifunctional flexible hose produced in the United Kingdom. Designed for water, air, and light chemicals. The hose material is free from phthalates, silicone, and cadmium, compliant with RoHS and WEEE regulations. According to EU requirements, use for food products is possible after conducting the required migration tests using appropriate model fluids simulating the specific type of food (the material used for hose production complies with the requirements of 10/2011/EU and FDA 21). The hose material is self-extinguishing according to UL94-V2 and UL94-HB (at a thickness of 3 mm). Inner layer: transparent PVC. Reinforcement: polyester braid. Outer layer: red (R) or blue (BL) PVC. Working pressure: from 10 bar to 18.3 bar - depending on the hose diameter. Operating temperature: from -20°C to +55°C (temporarily +65°C, cold bending temperature down to -45°C). As the operating temperature increases, the working pressure value of the hose decreases.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose designed specifically for transporting cooling water, used in metallurgical furnaces, transformer cooling systems, and electrical converters. Used in steel metallurgy. The outer layer is coated with fiberglass resistant to heat radiation up to +550°C (temporarily) and splashes of hot materials. The inner layer is insulating (dielectric), R>10^11Ω, resistant to electrical breakdown E≥6000 V/mm, with increased resistance to water and steam penetration under extreme operating conditions. The minimum bending radius in the technical specifications is given for pressures above 3 bar. Inner layer: light blue, insulating EPDM rubber. Reinforcement: synthetic cord. Outer layer: EPDM rubber coated with fiberglass. Working pressure: 20 bar. Operating temperature: from -35°C to +120°C, external up to +550°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsHose made according to platinum-enhancing technology of exceptional purity, intended for biotechnological applications. Resistant to high temperatures, ozone, radiation, moisture, and atmospheric conditions. Does not adsorb or absorb odor or taste. Can be repeatedly sterilized in an autoclave as well as with ethylene oxide or radiation. Meets FDA, USP Class VI, ISO 10993, European Pharmacopoeia 3.1.9, and Japanese Pharmacopoeia - Chapter 51 requirements. Safety factor 5:1. Material: transparent silicone. Hardness: 50° Shore (A). Density: 1.17 g/cm³. Operating temperature: from -65°C to +260°C. Hose length: 7.62 m, 15.24 m, or 30.48 m.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSUPER FLEX hose reinforced with polyester and steel spiral is designed for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, the version with fluorocarbon rubber is recommended. Standard length: 1000 mm. Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers + steel spiral (wire thickness 1.2 mm). Working pressure: from 2 bar to 8.12 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsStrong pressure hose with an inner layer made of chemically resistant ultra-high molecular weight polyethylene (UPE, UHMWPE). The inner layer is resistant to most acids and bases as well as many other aggressive chemicals (at elevated but not very high temperatures), making the hose widely used in the chemical and petrochemical industries. The UPE inner layer also complies with food hose requirements, free from phthalates and polycyclic aromatic hydrocarbons (PAH), features a low friction coefficient during flow, and prevents medium deposition on the walls. This significantly facilitates cleaning and allows for use in the cosmetic, pharmaceutical, and food industries as well. Reinforced with synthetic cord, built-in copper wires for electrostatic discharge. The outer layer is made of chemically resistant EPDM rubber, resistant to abrasion, ozone, and weather conditions. Compliant with EN 12115:2011 requirements (type M, resistance between hose ends R ≤ 100 Ω, guaranteed for hoses up to 40 m in length). Standards and requirements: Chemical hoses: EN 12115:2011. Food industry, contact with food (inner layer): 1935/2004/EC, 2023/2006/EC (GMP), 10/2011/EU (simulant fluids A, B, D2), FDA 21 CFR 177.1520, BfR III. Confirmation of resistance and application conditions requires contact with Tubes International, especially for temperatures above 50°C. Inner layer: white creamy UPE polyethylene. Reinforcement: synthetic cord. Outer layer: black EPDM rubber. Working pressure: 16 bar. Operating temperature: from -40°C to +100°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsSilicone elbow 180° reinforced with polyester is intended for cooling systems and heating systems in vehicles (water, coolant fluids, clean air or air with a small amount of oil mist). For oils, fuels, and oil mist, a version with a fluorosilicone inner layer is recommended. Standard arm length: 102 mm. Pressure safety factor: 3:1. The hose meets SAE J20R1 standards. Hardness (standard version) approx. 65° Shore (A), density approx. 1.26 g/cm³. Color of the outer layer: blue. Material: silicone rubber. Reinforcement: polyester spacers. Working pressure: from 2 bar to 8.12 bar (depending on hose diameter). Operating temperature: from -50°C to +180°C.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsColorless, crystal-clear, flexible chemical hose with a multi-layer construction featuring an inner layer made of FEP fluoropolymer with unique resistance and chemical inertness. It exhibits significantly greater flexibility than rigid hoses made entirely of Teflon or other fluoropolymers. The smooth inner layer, resistant and chemically inert, eliminates the risk of fluid contamination. Resistant to a wide range of chemicals from corrosive substances to MEK-based solvents. The hose meets hygiene requirements and is suitable for food contact: US FDA 21 CFR 177.1550, free from phthalates and BPA (Bisphenol A), non-toxic, and does not leave any odor or taste. Sterilization with ethylene oxide. Used in various industrial applications: chemical flow, pharmaceuticals, food and beverage production and packaging, paint, solvent and adhesive manufacturing, inks and toners, photographic chemicals, fertilizers and pesticides, in semiconductor production. Full hose roll length: 15 m. Working pressure defined relative to burst pressure with a safety factor of 1:5. Material: special FEP / PVC. Maximum operating temperature: +74°C. Brittleness temperature: -36°C. Hardness: 66° Shore (A). Density: 1.21 g/cm³. Note: Product packaged in the Clean Room of Tubes International (CLEAN ROOM) adhering to strict standards. Return of the product after opening the packaging is not possible.
- Select options This product has multiple variants. The options may be chosen on the product page / DetailsVery lightweight and flexible flat-folded suction hose with fittings for water for fire pumps. Used for fire, rescue, and forestry motor pumps. In addition to fire-fighting functions, widely used for water transfer in industry, construction, agriculture, and mining. The inner layer is smooth, resistant to mold and rot. The outer layer (braid) has high strength, with a polyurethane coating that does not retain dirt, increasing resistance to abrasion and contact with flames. Certifications: hoses compliant with the technical conditions of the MSWiA Regulation of April 27, 2010, hoses with fittings (complete hoses) have CNBOP-PIB approval certificates. Inner layer: smooth polyurethane. Reinforcement: polyester braid. Outer layer: red polyurethane coating. Working pressure: from 12 bar to 15 bar - depending on the hose diameter. Operating temperature: from -30°C to +70°C.
